Resin 3D Printer Process: Step by Step
Print, wash and harden a resin model step by step: the resin 3D printer process with the wash gear for each step.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ANYCUBIC Wash and Cure 3 with Gooseneck Lights9.7/10View on Amazon - 2
ELEGOO Mercury Plus 2.0 Wash and Cure Station9.6/10View on Amazon - 3
ANYCUBIC Wash and Cure Machine 3.0 with Twistable9.5/10View on Amazon - 4
ELEGOO Washing Bucket for Mercury X/XS Bundle Wash9.3/10View on Amazon
The resin 3D printer process runs in order: print the model, wash off the wet resin, harden the print under UV light, then check the finish. The wash and hardening steps decide the final finish.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

ANYCUBIC Wash and Cure 3 with Gooseneck Lights
A 2 in 1 wash station with gooseneck lights, a 4L bucket and a 165 x 100 x 180 mm wash size.
Pros
- Basket capacity up 42% over the older model
- Gooseneck lights raise the energy value by 30,000uW/cm²
- Double-layer basket saves IPA
- Hardening 20% more uniform
Cons
- Washing size limited to 165 x 100 x 180 mm
- Fits printers 7.3 inches or less
- No UV LED wavelength stated
- No hardening size stated

ELEGOO Mercury Plus 2.0 Wash and Cure Station
A wash station with 16 pieces of 405nm UV LED and a 360-degree turntable, washing models up to 5.16 x 3.54 x 8.66 inches.
Pros
- 16 pieces of 405nm UV LED, 360-degree turntable
- Anti-UV lid blocks 99.95% of ultraviolet rays
- Sealed washing prevents alcohol from volatilizing
- Basket or build plate washing
Cons
- No warranty term stated
- Not suitable for water washable resin prints
- Washing size limited to 5.16 x 3.54 x 8.66 inches
- No hardening time range stated

ANYCUBIC Wash and Cure Machine 3.0 with Twistable
A 2 in 1 wash machine with a twistable gooseneck light, a 4L bucket and a hardening size of up to 160 x 180 mm.
Pros
- Gooseneck light raises the energy value by 30,000uW/cm²
- Hardening 20% more uniform
- Washing size up to 165 x 100 x 180 mm
- Runs at no more than 65db
Cons
- No warranty term stated
- No UV LED wavelength stated
- Fits printers 7.3 inches and below
- No anti-UV lid stated

ELEGOO Washing Bucket for Mercury X/XS Bundle Wash
A 7000ml washing bucket for the Mercury X and XS wash stations, handling the wash step with two washing modes.
Pros
- 7000ml capacity for batch cleaning
- Two washing modes: basket washing and suspension washing
- Sealed washing with rubber sealing
- PP plastic body with good chemical stability
Cons
- A bucket only, needs a Mercury X or XS machine
- No hardening function stated
- Fits only the Mercury X and XS bundle stations
- The 7-liter tank needs more cleaning liquid
Step 1: Print the model
Print the model and lift the build plate with the model still on it. The wash stations below take models on the build plate or in a basket. If the printer itself is still undecided, our best 3D resin printers guide compares the models these stations are built for.
Step 2: Wash off the wet resin
Wash the print in IPA, in a basket or with the build plate hung on the rack. The ELEGOO Mercury Plus 2.0 washes models up to 5.16 x 3.54 x 8.66 inches, and the ANYCUBIC stations wash up to 165 x 100 x 180 mm. Sealed washing keeps the alcohol from volatilizing.
Step 3: Harden the print under UV light
Harden the washed print under UV light. The Mercury Plus 2.0 uses 16 pieces of 405nm UV LED with a 360-degree rotating turntable, and the ANYCUBIC stations add gooseneck lights that raise the energy value by 30,000uW/cm² within a 1-3 cm irradiation range for small areas. Hardening time runs 1 to 30 minutes on the ANYCUBIC stations.
Step 4: Check the finish and clean up
Check the print for sticky spots or soft areas, and harden it again where the surface still feels wet. The ANYCUBIC machine with the twistable gooseneck light runs at no more than 65db.
The gear for the resin 3D printer process
Washing and hardening are the two steps that need gear, and the picks below cover both steps between them: three wash and harden, and the bucket covers washing alone. Pair them with a resin from our best 3D printing resins guide.
Common mistakes to avoid
- Washing a water washable resin model in the wash station instead of running water.
- Touching wet resin with bare hands.
- Skipping the hardening step and leaving the print soft.
- Buying a station too small for the print.
- Running the hardening step with the lid or cover off.
Resin 3D printer process: the short version
- Print the model and lift the build plate.
- Wash the print in IPA, in a basket or on the build plate.
- Harden the print under UV light.
- Check the finish and harden it again where the surface still feels wet.
FAQ: lasers and CNC
How long does the resin 3D printer process take?
Washing and hardening time runs 1 to 30 minutes on the ANYCUBIC stations. The print time itself depends on the model and the printer.
What size print can a wash station handle?
The Mercury Plus 2.0 washes up to 5.16 x 3.54 x 8.66 inches, and the ANYCUBIC stations wash up to 165 x 100 x 180 mm.
Can I wash a water washable resin print in a wash station?
The ELEGOO Mercury Plus 2.0 listing says its washing function is not quite suitable for water washable resin prints, which are better washed with running water.
What does the gooseneck light do?
The gooseneck light raises the energy value by 30,000uW/cm² within a 1-3 cm irradiation range, strengthening the hardening on small areas such as the top of a model.
Related: the 3D printer hub, resin 3D printers and 3D printing resin types.




