Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Pva vs Hips Filament: Which One Should You Buy?

A guide to choosing between PVA and HIPS support filament, comparing PVA listings by water removal, settings, storage, and dual-material setup.

Pva vs Hips Filament: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1iSANMATE 16KG Matte PLA Filament Bundle 1.75MM 30-300mm/s foriSANMATE 16KG Matte PLA Filament Bundle 1.75MM 30-300mm/s for9.7/10View on Amazon
  2. 2Comgrow Filament Dryer 4 SpoolsComgrow Filament Dryer 4 Spools9.7/10View on Amazon
  3. 3iSANMATE 10KG HF PETG Filament Bundle Black Rapid 50-400mm/siSANMATE 10KG HF PETG Filament Bundle Black Rapid 50-400mm/s9.7/10View on Amazon
  4. 4ANYCUBIC PVA FilamentANYCUBIC PVA FilamentView on Amazon
  5. 5RepRapper PVA FilamentRepRapper PVA FilamentView on Amazon
  6. 6RepRapper PVA Filament 1.75mm for 3D PrinterRepRapper PVA Filament 1.75mm for 3D PrinterView on Amazon
  7. 7YOUSU Upgraded PVA Filament 1.75mmYOUSU Upgraded PVA Filament 1.75mmView on Amazon
  8. 8Polymaker PolyDissolve S1 PVA FilamentPolymaker PolyDissolve S1 PVA FilamentView on Amazon
  9. 9Fused Materials PVA Filament 1.75mmFused Materials PVA Filament 1.75mmView on Amazon

Pva vs hips filament comes down to how the support comes off: the PVA listings in this guide dissolve or soften in water, while no HIPS listing is featured here, so a HIPS choice needs its own listing check. For complex prints with steep overhangs, internal cavities, and fine details, a dissolving support can avoid manual removal, while softening types still need peeling by hand.

Other machines to compare

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Pva vs hips filament: the short answer

PVA is the water-soluble support side of this comparison in the listings below, and HIPS is the other support material named in the keyword. No HIPS listing is included here, so this guide does not rate a HIPS filament, and a HIPS decision should rest on a HIPS listing and its stated removal method. For readers who print with two materials and want supports that come off in water, the PVA listings give a workable route, with one split: some dissolve supports outright, others soften them for peeling by hand, and Yousu combines both. A related hips vs abs filament comparison covers a different pairing.

In the order below, Polymaker gives the fullest stated settings; Yousu and RepRapper state temperatures, while ANYCUBIC states no temperatures or diameter, and RepRapper comes last because its listing contradicts itself on solubility and spool size.

How PVA supports come off

Water removal is the reason to pick PVA, but the listings do not all describe the same removal. Dissolving means the support disappears in water, while softening means warm water loosens it for peeling by hand. That difference matters for enclosed channels and tight spaces.

  • Polymaker PolyDissolve S1 PVA, 750g, 1.75mm: dissolves in water for internal cavities and tight spaces, with time varying by thickness, water temperature, and movement.
  • ANYCUBIC PVA, 500g: described as 100% water-soluble, dissolved in water for complex internals, ball joints, and fine details, with no manual removal stated.
  • Yousu PVA, 500g, 1.75mm: faster water dissolution than the previous generation, with softening at 50-65°C so supports peel off by hand, protecting delicate surfaces.
  • RepRapper PVA, 0.5kg, 1.75mm: its bullets say it is not soluble in water, but softens at 60-80°C water temperature for manual peeling, with large areas easy to remove and tiny areas hard to remove, such as between parts inside.

Diameter is stated as 1.75mm for Polymaker, Yousu, and RepRapper; ANYCUBIC states no diameter, so do not assume it matches.

The gear in this guide

The listings below are all PVA.

Polymaker PolyDissolve S1 PVA

Polymaker PolyDissolve S1 is a 750g, 1.75mm PVA support filament formulated for PLA, TPU, PVB, and Nylon-based filaments in the Polymaker portfolio. Its listing directs readers to assign S1 to support structures or interface layers in the slicer for overhangs, enclosed channels, and detailed geometry.

The stated TDS settings are 215-225°C nozzle and 25-60°C bed for a 0.4mm nozzle, with the cooling fan on, and a purge when sharing a nozzle. On moisture, PVA absorbs moisture quickly, so keep the spool sealed, print from a dry box, and dry when needed, with the TDS listing 80°C for 12 hours for material that has absorbed moisture. When changing profiles, check the model material and run an interface check.

ANYCUBIC PVA Filament

ANYCUBIC PVA is a 500g, Natural support filament described as a water-soluble support material for intricate prints and steep overhangs, dissolved in water while preserving fine details with no manual effort stated. Its listing names PLA, PETG, and TPU as filaments it supports, with reliable adhesion and solid support structures. Packaging is vacuum-sealed in high-barrier aluminum foil with an anti-moisture seal, and the reusable spool uses a threaded connection system for stable pairing with spool-free filaments.

No nozzle temperature, bed temperature, print speed, or diameter is stated in the ANYCUBIC listing, so those settings are Not stated here rather than borrowed from another listing.

Yousu PVA Filament

Yousu PVA is a 500g, 1.75mm filament with a stated tolerance of ±0.02mm, controlled by CCD measurement and adaptive systems, for consistent feeding. It works with PLA and other low-temp filaments at similar printing settings of 180-210°C. Removal combines faster dissolution than the previous generation with softening at 50-65°C, so supports peel off by hand, protecting delicate surfaces.

Packaging is a vacuum-sealed bag with a desiccant packet to lock out humidity, and the listing says to use PVA as soon as possible after opening the vacuum bag. The listing also says the filament is dried for 24 hours at constant temperature before vacuum sealing, and precision winding helps prevent tangling and breakage; the drying step reduces air bubbles, stringing, and nozzle clogging.

RepRapper PVA Filament

RepRapper PVA is a 0.5kg, 1.75mm filament, and its listing contradicts itself twice. The title calls it a water soluble filament, while its bullets say it is not soluble in water, but softens at 60-80°C water temperature so supports can be manually peeled off without damaging the printed surface. Separately, the title states 0.5kg, while a bullet about AMS compatibility describes a 1kg plastic spool. Both contradictions are stated here as they appear, and the peeling procedure in the bullets is the removal method the listing actually describes.

The stated print settings are a nozzle temperature of 230-240°C, a bed temperature of 40-60°C, and a print speed of 40-100 mm/s, with drying at 50-60°C for 6-8 hours before printing each time. Compatibility is described as almost all FDM 3D printers. The listing also says the filament is mechanically wound and precisely spooled to prevent tangling or overlapping, with CCD checks stated. The practical limit is the one the listing states itself: large areas are easy to remove, but tiny areas are hard to remove, such as between parts inside.

Settings belong to one listing at a time. Copying a nozzle or bed temperature from a different listing can mismatch a support material with its print, since the PVA listings here share no temperature range.

  • Polymaker: 215-225°C nozzle, 25-60°C bed, 0.4mm nozzle, cooling fan on.
  • ANYCUBIC: nozzle and bed temperatures Not stated.
  • Yousu: 180-210°C with PLA and other low-temp filaments; bed temperature Not stated.
  • RepRapper: 230-240°C nozzle, 40-60°C bed, 40-100 mm/s print speed, dry at 50-60°C for 6-8 hours before printing each time.

Diameter is another listing-by-listing check: a filament diameter comparison is useful background, but the listings here state 1.75mm except for ANYCUBIC, which states no diameter. Match the diameter the listing states to the printer setup, rather than assuming every PVA spool shares it.

Moisture and storage

PVA and moisture do not mix well in these listings. Polymaker states that PVA absorbs moisture quickly, and its advice is to keep the spool sealed, print from a dry box, and dry material that has absorbed moisture at 80°C for 12 hours per its TDS. A filament dry box guide covers that storage step. ANYCUBIC ships vacuum-sealed in high-barrier aluminum foil, and Yousu ships in a vacuum-sealed bag with a desiccant packet, to be used as soon as possible after opening. RepRapper takes a different routine: dry at 50-60°C for 6-8 hours before printing each time.

Dual-material setup

Support filament only helps if the printer can lay down two materials in one print. Polymaker recommends a two-nozzle, IDEX, or toolchanger printer, with a purge when sharing a nozzle. RepRapper mentions AMS compatibility, but that bullet is the same one that describes a 1kg plastic spool against a 0.5kg title, so the spool size in that bullet should not be trusted on its own. ANYCUBIC describes a reusable spool with a threaded connection for spool-free filaments, without naming a dual-material printer setup; Yousu names none either.

Common mistakes to avoid

  • Copying nozzle or bed temperatures from a different listing instead of the chosen listing’s own settings.
  • Leaving PVA open after opening the vacuum bag, when Yousu says to use it soon after opening and Polymaker says it absorbs moisture quickly.
  • Expecting RepRapper supports to dissolve, when its bullets describe softening and manual peeling, with tiny areas hard to remove.
  • Skipping an interface check when changing profiles, which the Polymaker listing advises.
  • Assuming the ANYCUBIC diameter matches the others, when its listing states no diameter.

FAQ: lasers and CNC

Is PVA really water soluble?

It depends on the listing. ANYCUBIC describes its PVA as 100% water-soluble, Polymaker says its S1 dissolves in water, Yousu combines faster dissolution with softening at 50-65°C, and RepRapper bullets say its PVA is not soluble in water but softens for peeling.

Which PVA here lists PLA compatibility?

ANYCUBIC lists PLA, PETG, and TPU, Yousu lists PLA and other low-temp filaments, and Polymaker lists PLA, TPU, PVB, and Nylon-based filaments in its portfolio. RepRapper lists compatibility with almost all FDM 3D printers without naming PLA separately.

What nozzle and bed temperatures do the listings state?

RepRapper states 230-240°C nozzle and 40-60°C bed, Polymaker states 215-225°C nozzle and 25-60°C bed for a 0.4mm nozzle, and Yousu states 180-210°C with PLA. ANYCUBIC states neither temperature, and Yousu states no bed temperature.

Why is HIPS not rated here?

No HIPS listing is included in the listings for this guide, so this guide does not rate a HIPS filament. A HIPS decision should rest on a HIPS listing and its stated removal method and settings.

How should PVA be stored?

Keep it sealed and dry: Polymaker advises a dry box and drying at 80°C for 12 hours for absorbed moisture, RepRapper advises drying at 50-60°C for 6-8 hours before each print, and Yousu advises using it soon after opening its vacuum bag.

Related: the FDM 3D printers hub, hips vs abs filament and filament dryer vs dry box.

More buying guides

3D Printer Accessories ·

Best Spray Paint for Hard Plastic (2026)

Four spray paints for hard plastic, from a plastic-specific trim restorer to a textured automotive topcoat, compared by coverage, dry time and finish.