Linear Guide Bearing: Types and Sizes for CNC
A linear guide bearing carries the moving carriage of a CNC machine along its rail, and this guide explains the HGH and SBR types, sizes and uses from the listings.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ANWOKIT SBR20 Linear Rail Spliced Linear Guide9.6/10View on Amazon - 2
HGH15CA Linear Slider Bearing Blocks 4Pcs,15mm9.6/10View on Amazon - 3
LD-Teemm HGH20CA Linear Slider Bearing9.6/10View on Amazon - 4
Mssoomm 2 Pcs SBR20LUU SBR20 LUU 20mm Linear9.5/10View on Amazon
A CNC router only cuts as straight as its motion system lets it. The gantry rides on rails, and the part that rides is the bearing block: a small carriage packed with ball bearings that rolls along the rail and carries the spindle. Linear guide bearing is the name for that block, and this guide explains the types in the listings, the sizes they come in, and which one fits each part of a CNC build.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

ANWOKIT SBR20 Linear Rail Spliced Linear Guide
A complete SBR20 rail set with 4 rail shafts at 1500 mm, 8 SBR20UU blocks and hardware, listed as a 3000 mm set for CNC machines and 3D printers.
Pros
- 4 rails at 1500 mm each, listed as a 3000 mm set
- 8 SBR20UU blocks included
- Rails, blocks and hardware in one listing
- Steel and aluminum alloy with chrome plating
Cons
- No warranty term is stated
- No load figure is stated
- Listing calls it a 3000 mm set while listing 4 shafts at 1500 mm each
- Size is 3000 mm only in this listing

HGH15CA Linear Slider Bearing Blocks 4Pcs,15mm
A pack of 4 HGH15CA square carriage blocks in 15 mm, made from steel with corrosion resistance, with a Gothic four-point contact design.
Pros
- 4 blocks in one listing
- Gothic four-point contact, self-aligning
- Steel with corrosion resistance
- Interchangeable by industrial standard
Cons
- No warranty term is stated
- No rail length is stated
- No load figure is stated
- No rail included; blocks only

LD-Teemm HGH20CA Linear Slider Bearing
A pack of 2 HGH20CA square bearing slider blocks in bearing steel, with steel balls for low friction, for HG20 CNC linear guides.
Pros
- Bearing steel with steel balls for low friction
- High rigidity and high load stated
- Interchangeable with other square rail kits
- 2 blocks for an HG20 rail
Cons
- No warranty term is stated
- No load figure is stated
- No rail length is stated
- No rail included; blocks only

Mssoomm 2 Pcs SBR20LUU SBR20 LUU 20mm Linear
Long SBR20LUU slide blocks in aluminum alloy for a 20 mm linear guide rail, with a high precision motion ball for smooth movement.
Pros
- Aluminum alloy long slide block
- High precision motion ball for smooth movement
- Fits SBR20 20 mm rails
- Stated for CNC routers, mills and lathes
Cons
- No warranty term is stated
- Title says 2 pieces, table lists 1 item
- No rail length is stated
- No load figure is stated
Linear guide bearing: the quick answer
A linear guide bearing is a recirculating ball bearing block that rides on a linear rail and carries a moving carriage, such as a CNC gantry or spindle mount. The listings here cover HGH square blocks and SBR round rail blocks, sold as blocks alone or as full rail sets. Pick the family that matches the rail already on the machine, then the size, then the pack count the build needs.
HGH square blocks
The HGH blocks are square carriages that run on square rails. The LD-Teemm listing sells the HGH20CA as a pack of 2 blocks in bearing steel, with steel balls for low friction, and states high rigidity and high load for the HG series. The Coavoo listing sells the HGH15CA as a pack of 4 blocks in 15 mm, made from steel with corrosion resistance, using a Gothic four-point contact design that withstands loads in all directions and self-aligns. The LD-Teemm listing states its blocks are interchangeable with other square linear rail kits, and the Coavoo listing states good interchangeability by industrial standard.
SBR round rail sets and blocks
The SBR family runs on round rails with a support rail under them. The ANWOKIT listing is a complete set: 4 SBR20 rail shafts at 1500 mm each, 8 SBR20UU blocks, and the hardware to join them into a 3000 mm set, with 2 wrenches, 2 locking handles, 32 screws and 4 dowels. The rails are steel and aluminum alloy with a chrome plating treatment. The Mssoomm listing sells long SBR20LUU blocks in aluminum alloy for a 20 mm rail, with a high precision motion ball inside for smooth, low friction movement.
Linear guide bearing picks
The picks below handle the motion step itself: bearing blocks that ride a rail and carry a carriage, plus one full rail set, ranked by the stated size, material, pack count and listing detail.
How to choose a linear guide bearing
Match the block to the rail. The HGH20CA blocks fit HG20 rails, the HGH15CA blocks fit HGR15 rails, and the SBR20LUU blocks fit SBR20 rails in 20 mm. The ANWOKIT SBR20UU blocks (on Amazon) fit the SBR20 rails in that kit. If the rail is already on the machine, buy the block that names it; if the build starts from nothing, the ANWOKIT kit is the only listing here that includes rails, blocks and hardware together.
FAQ: lasers and CNC
What does a linear guide bearing do?
It carries a moving carriage along a rail. Ball bearings inside the block roll on the rail with low friction, so the gantry or spindle mount moves smoothly and holds its line.
What is the difference between HGH and SBR linear guide bearings?
HGH blocks are square carriages that run on square rails, while SBR blocks run on round rails with a support rail under them. The listings here show HGH in 15 mm and 20 mm sizes and SBR in 20 mm.
What size linear guide bearing do I need?
Match the rail: HGH15CA for 15 mm rails, HGH20CA for HG20 rails, and SBR20LUU for SBR20 rails in 20 mm. The size is in the model name on each listing.
How many blocks come in a pack?
The LD-Teemm listing sells 2 blocks, the Coavoo listing sells 4 blocks, the Mssoomm listing states 2 blocks in its title and bullets while its spec table lists 1 item, and the ANWOKIT listing includes 8 blocks with its rails.
Can I replace only the block, or do I need a new rail?
Only the block, per the LD-Teemm listing: its blocks are interchangeable with other square linear rail kits, and the listing says the slider or the guide rail can be replaced. Check the fit against the rail already on the machine.
Related: the CNC routers hub, linear guide rails vs round linear rods, linear rails vs V wheels CNC and the best CNC machine for home shop guide.




