Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Types of Linear Rails for CNC Machines

A guide to the types of linear rails for CNC machines, comparing supported round shaft and profile guide rails with four kits for routers, lathes and 3D printers.

Types of Linear Rails for CNC Machines
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1iMetrx HGR20 Linear Guide Rail KitiMetrx HGR20 Linear Guide Rail Kit9.6/10View on Amazon
  2. 2VEVOR Linear Rail Kit, 4Pcs Bearing Slide BlocksVEVOR Linear Rail Kit, 4Pcs Bearing Slide Blocks9.6/10View on Amazon
  3. 3VEVOR Linear Rail, 2PCS SBR16-1000mmVEVOR Linear Rail, 2PCS SBR16-1000mm9.6/10View on Amazon
  4. 4CHUANGNENG Linear Rail 2PCS HGR20 900mm LinearCHUANGNENG Linear Rail 2PCS HGR20 900mm Linear9.5/10View on Amazon

Types of linear rails for a CNC machine come down to two main designs: supported round shaft rails, sold as SBR kits, and profile guide rails, sold as HGR kits. Supported round shaft rails carry the shaft on a base along its full length, while profile guide rails run a block along a shaped steel rail. The right pick depends on the machine, the travel length and the load the axis carries, and the four kits below cover both designs in lengths a home CNC router build can use.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

iMetrx HGR20 Linear Guide Rail Kit

iMetrx HGR20 Linear Guide Rail Kit

iMetrx9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A profile guide rail kit with two 1500mm HGR20 rails and four HGH20CA blocks for CNC routers, lathes and 3D printers.

Pros

  • Two 1500mm HGR20 rails with four HGH20CA blocks
  • Bearing steel rails with a rust-resistant surface treatment
  • Aluminum alloy blocks with internal linear bearings
  • Pre-drilled holes, with stated use on CNC routers

Cons

  • No load rating is stated in the listing
  • No weight is stated in the listing
  • No warranty term is stated
  • Bullets mention an optical axis, which does not match the HGR20 profile rail
VEVOR Linear Rail Kit, 4Pcs Bearing Slide Blocks

VEVOR Linear Rail Kit, 4Pcs Bearing Slide Blocks

VEVOR9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A supported round shaft rail kit with two 2000mm SBR20 rails and four slide blocks for cutting, milling and drilling machines.

Pros

  • Two 78.74 in (2000 mm) rails, the longest here
  • Carbon steel shafts rated HRC58–66, coating over 10 μm
  • Surface finish of 0.1–0.22 μm and 5 mΩ straightness
  • Ball-bearing slide blocks for quiet, low-friction travel

Cons

  • Item weight of 28.99 pounds
  • No warranty term is stated
  • No load rating is stated in the listing
  • 2000mm rails need room for that travel
VEVOR Linear Rail, 2PCS SBR16-1000mm

VEVOR Linear Rail, 2PCS SBR16-1000mm

VEVOR9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A supported round shaft rail kit with two 1000mm SBR16 rails and four SBR16UU blocks, with stated load ratings per block.

Pros

  • Dynamic load of 774 N and static load of 1180 N per block
  • Two 39.4 in (1000 mm) rails with four SBR16UU blocks
  • Carbon steel shaft with a chrome-plated surface
  • Stated use on router, mill and lathe sleds

Cons

  • Shorter than the 2000mm SBR20 kit
  • No warranty term is stated
  • No coating thickness is given for the chrome plating
CHUANGNENG Linear Rail 2PCS HGR20 900mm Linear

CHUANGNENG Linear Rail 2PCS HGR20 900mm Linear

CHUANGNENG9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A profile guide rail kit with two 900mm HGR20 rails and four HGH20CA blocks for DIY CNC routers, lathes and mills.

Pros

  • Two 900mm HGR20 rails with four HGH20CA blocks
  • Pre-drilled support rails for easy installation
  • Oxidation treatment stated for a rust-proof finish
  • Stated use on CNC machines, industrial robots and mills

Cons

  • No load rating is stated in the listing
  • No weight is stated in the listing
  • No warranty term is stated
  • Smallest rails in this guide at 900mm

Supported round shaft rails (SBR)

An SBR rail is a round carbon steel shaft on an aluminum support base, with SBR16UU or SBR20 slide blocks that carry ball bearings. The VEVOR SBR20 kit pairs 78.74 in (2000 mm) rails with a coating of more than 10 μm, shafts rated HRC58–66 and a stated surface finish of 0.1–0.22 μm. The VEVOR SBR16 kit is shorter at 39.4 in (1000 mm) and states a dynamic load of 774 N and a static load of 1180 N per block.

SBR kits suit long, straight axes where the rail can sit on a flat base, such as a router gantry or a mill table. The support base limits how much the shaft can flex over long travel, which matters most on the 2000mm kit. For a closer look at how the two rail shapes compare, see linear guide rails vs round linear rods.

Profile guide rails (HGR)

An HGR rail is a shaped steel rail with HGH20CA blocks that wrap the rail, giving a stiff, compact axis that resists twisting loads. The iMetrx kit (on Amazon) offers two 1500mm HGR20 rails with four HGH20CA blocks, bearing steel rails with a rust-resistant surface treatment and aluminum alloy blocks with internal linear bearings. The CHUANGNENG kit (on Amazon) is the compact option, with two 900mm HGR20 rails and four HGH20CA blocks and a stated guide length of 35.43 inch.

Profile rails suit machines where the axis must stay rigid in a small space, such as a 3D printer frame, a lathe carriage or a compact CNC router. Both HGR kits in this guide state pre-drilled holes, so mounting is a matter of bolting the rail to a flat surface. The linear rails vs V wheels CNC guide covers how a profile rail compares with wheel-based motion.

How to choose between the types of linear rails

Start with the travel the axis must cover, then check the load each block must carry. SBR kits publish the shaft size in the model name, so SBR16 and SBR20 kits are easy to tell apart, while HGR kits publish the rail size as HGR20. Where a listing states a load rating, compare it with the weight of the gantry, spindle and workpiece the axis will move. Both rail types need a flat, straight base, and the listings state mounting holes on the rails in this guide. Rust resistance matters in a damp workshop: the kits here state chrome plating, an electroplated layer, an oxidation treatment or a rust-resistant surface treatment.

Linear rail kits for CNC machines

Once the rail type and the travel length are settled, these four kits put the rail and the blocks together for a CNC router, lathe, mill or 3D printer build, scored on the method described on the scoring method page.

FAQ: lasers and CNC

What is the difference between SBR and HGR linear rails?

SBR rails are supported round shaft rails: a round steel shaft on an aluminum base, with slide blocks that ride the shaft. HGR rails are profile guide rails: a shaped steel rail with blocks that wrap the rail.

Which linear rail length fits a CNC router?

It depends on the travel the axis must cover. The kits in this guide run from 900mm to 2000mm, so measure the full stroke of the axis, including the blocks at each end, and pick a rail that covers it with room to spare.

Do linear rails come with pre-drilled mounting holes?

The kits in this guide state mounting holes, and the listings describe mounting as simple, with no extra installation tools required for the SBR20 kit.

Can linear rails be used on a 3D printer?

Yes, the listings state 3D printer use for the iMetrx HGR20 kit and the VEVOR SBR16 kit, alongside CNC routers, lathes and milling machines.

Related: the CNC routers hub and the best CNC router guide. Also see how to set up a spoilboard on a CNC.

More buying guides

CNC Routers ·

Linear Bearing Guide Rail: How to Choose

A practical guide to choosing a linear bearing guide rail: rail type, length, load figures and block style, with kits compared for CNC router…