Curved Linear Guide Rail: Types and Buying Tips
A curved linear guide rail carries a carriage around an arc instead of a straight line: types, straight vs curved rails, and four DIY rail kits compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Linear Rail Guide Kit9.5/10View on Amazon - 2
VEVOR Linear Rail, 2PCS SBR20-1200mm9.5/10View on Amazon - 3
ANWOK Linear Guide Rail 2PCS HGR15-1000mm Linear9.4/10View on Amazon - 4
MGN12H 150mm Linear Rail 5.9'' with MGN12H Steel9.4/10View on Amazon
A curved linear guide rail is a rail made to follow an arc that carries a carriage around a curve instead of along a straight line, so a machine can follow a bend, a circle or a sweeping path without stopping to reposition the work. Straight rails run along a straight line only, while a curved rail keeps the carriage on its arc through the whole travel. This guide explains the types, what to check before buying, and the straight rail kits below.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

VEVOR Linear Rail Guide Kit
A kit with 2 rails of 1000 mm, 34 end caps, 4 clamps and 4 blocks for DIY CNC routers and mills.
Pros
- 0.05 mm per 1000 mm straightness stated
- Medium-carbon steel at HRC58-62
- Electroplated coating of at least 10 μm
- 34 end caps and 4 rail clamps included
Cons
- No warranty term is stated
- No load rating is stated
- No safety certification is stated
- No curved or arc version is stated

VEVOR Linear Rail, 2PCS SBR20-1200mm
A kit with 2 rails of 1200 mm and 4 bearing blocks in carbon steel with chrome plating, for automated machines and DIY CNC builds.
Pros
- Longest rails here at 1200 mm (47 inches)
- Carbon steel rails with chrome plating
- 4 bearing blocks with aluminium alloy housings
- Listed for DIY CNC routers, lathes and machine tools
Cons
- Title says SBR16UU blocks, bullets say SBR20UU
- No warranty term is stated
- No load rating is stated
- No safety certification is stated

ANWOK Linear Guide Rail 2PCS HGR15-1000mm Linear
A kit with 2 HGR15 rails of 1000 mm and 4 HGH15CA bearing blocks for DIY CNC routers, lathes and mills.
Pros
- 2 rails of 1000 mm with 4 HGH15CA blocks
- High load carrying capacity stated
- Smooth running with low noise, per the listing
- Slider, rail or guide group replaceable separately
Cons
- No warranty term is stated
- No load rating figure is stated
- No material or hardness figure is stated
- No safety certification is stated

MGN12H 150mm Linear Rail 5.9'' with MGN12H Steel
A 150 mm linear rail with one MGN12H steel carriage block for small DIY machines, 3D printers and plasma cutters.
Pros
- Compact 150 mm (5.9 inch) rail for small builds
- Bearing steel rail with blackening treatment
- Stainless steel carriage block, pre-loaded
- Rubber stoppers on each side stop the block falling out
Cons
- No warranty term is stated
- Only one rail and one block in the kit
- Shortest travel here at 150 mm
- No load rating is stated
What a curved linear guide rail is
A curved linear guide rail is a profile rail made to follow an arc rather than a straight line. Blocks matching the rail keep the carriage on the arc as it moves. The curve is set when the rail is made, so the radius is fixed and the rail cannot be bent to a new curve later. Common forms are arc rails and ring rails.
Straight rails vs curved rails
The four kits here are straight rails in the two forms a DIY builder meets most often: profile rails and round-shaft rails. The ANWOKIT HGR15 (on Amazon), VEVOR HGR20 and NUIBBYED MGN12H (on Amazon) are profile rails, where the block wraps the rail, and the VEVOR SBR20 is a round-shaft rail on a support.
How to choose a curved linear guide rail
Match the rail to the machine
The kits here run from 150 mm to 1200 mm. The NUIBBYED rail is 150 mm (5.9 inches), the ANWOKIT and VEVOR HGR20 rails are 1000 mm (39.37 inches), and the VEVOR SBR20 rails are 1200 mm (47 inches). The ANWOKIT, VEVOR SBR20 and VEVOR HGR20 kits each include 2 rails and 4 blocks; the NUIBBYED kit includes 1 rail and 1 block.
Blocks, preload and fit
Blocks must match the rail size: HGH15CA on the ANWOKIT kit, HGH20CA on the VEVOR HGR20 kit, and MGN12H on the NUIBBYED kit. The NUIBBYED block is pre-loaded, with two rubber stoppers on each side to stop it falling out. Check the block size: the VEVOR SBR20 title says 4 SBR16UU blocks while the bullets say 4 SBR20UU blocks.
Materials and corrosion protection
The VEVOR HGR20 kit states medium-carbon steel at HRC58-62 with an electroplated coating of at least 10 μm, a surface finish of 0.1-0.22 μm and straightness of 0.05 mm per 1000 mm. The VEVOR SBR20 kit states carbon steel rails with chrome plating. The NUIBBYED rail is bearing steel with a blackening treatment against rust, and its block is stainless steel.
Gear for the build
The kits below handle straight-line travel in DIY builds.
Common mistakes to avoid
- Ordering a straight rail for a curved path.
- Mixing block and rail sizes.
- Skipping corrosion protection in a damp shop.
- Ignoring straightness on a long axis.
- Buying one rail and one block without checking how many rails and blocks the axis needs.
FAQ: lasers and CNC
What is a curved linear guide rail?
A curved linear guide rail is a rail made to follow an arc that carries a carriage around a curve.
Can I use a straight linear rail on a curved path?
No. The kits here are straight rails for straight travel, and a straight rail cannot be bent into a curve.
What length linear rail do I need?
The kits here run from 150 mm (5.9 inches) to 1200 mm (47 inches).
How do you install a linear guide rail?
That depends on the kit: the VEVOR SBR20 listing describes its own install as aligning the track with the mouth of the slide rail and pushing until it falls into place.
What is the difference between HGR and SBR rails?
HGR rails are profile rails where the block wraps the rail. SBR rails are round-shaft rails on a support.
Related: the best CNC router for sign making, linear guide rails vs round linear rods and linear rails vs V wheels CNC.




