Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Work a Button Maker: Step-by-Step Guide

Fit the mold, cut the design, load the parts and press the lever: a button maker turns paper and parts into a finished pin in a short sequence.

How to Work a Button Maker: Step-by-Step Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Caydo Electric Button Maker Machine Multiple SizesCaydo Electric Button Maker Machine Multiple Sizes9.7/10View on Amazon
  2. 2Happizza Button Maker Machine Multiple SizesHappizza Button Maker Machine Multiple Sizes9.7/10View on Amazon
  3. 3MK.Bear Button Maker MachineMK.Bear Button Maker Machine9.7/10View on Amazon

How to work a button maker comes down to a short sequence: fit the mold for the size you want, cut the design to match, load the parts in the right order, and pull the lever to close the front, then again to crimp the back. The machine does the pressing; your job is the order of the parts and the size of the cut. This guide walks through each step in order, with the mistakes that waste parts and the fixes that keep buttons crisp.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Before pressing a button

Read the step-by-step instructions in the box before pressing a button. Get the order of the parts right; the lever does the pressing.

Set up before pressing a button

Clear a flat surface and lay out the kit: the machine, the molds, the circle cutter, the cutting mat and the button parts. Read the step-by-step instructions in the box, then pick the size for the batch. The machine measures 10.0 inches by 7.0 inches by 11.0 inches, so it fits on a craft table with room for the mat beside it.

Pick the size and fit the mold

Button makers come in sizes, and this kit covers 3: 1 inch, 1.25 inch and 2.25 inch, or 25 mm, 32 mm and 58 mm. The kit holds 3 sets of quickly interchangeable molds, so swap the mold to change size. Pick the size before cutting the design, since the cut must match the mold.

Cut the design to size

Cut the design with the adjustable circle cutter on the A5 cutting mat. The cutter adjusts to the size of the mold, so set it for the size you picked before cutting. For 25 mm and 32 mm buttons, use thicker pattern paper, slightly thicker than A4 paper, or use two layers of paper. Thicker paper holds its shape in the press and keeps small buttons crisp.

Load the parts in order

A button is built from the shell, the design, the clear cover and the pin back, loaded in that order. Set the shell in the mold, face down, then lay the design on top, then the clear cover. Pull the lever to close the front of the button.

Then set the pin back in the other side of the mold, swing it under the lever and pull the lever again to crimp the back on. The built-in metal pressure lever does the crimping, so a steady pull beats a hard slam. Hold the lever down for a moment, then release and lift the finished button out. Check the edge all the way around: the cover should sit flat and the pin back should sit tight.

What comes in the kit

The kit holds 300 sets of button parts, 100 of each size, with 3 sets of molds, an adjustable circle cutter and an A5 cutting mat. The machine is made of high-strength engineering plastics with a built-in metal pressure lever, and the listing states a 1 year manufacturer warranty.

Common mistakes to avoid

  • Cutting the design before picking the size. The cut must match the mold, so pick the size and fit the mold before cutting.
  • Using thin paper for small buttons. For 25 mm and 32 mm buttons, use thicker pattern paper, slightly thicker than A4 paper, or two layers of paper.
  • Loading the parts in the wrong order. The shell goes in face down, then the design, then the clear cover. The pin back goes in after the front is pressed.
  • Putting the shim washer in the machine. The listing warns against it: do not put the shim washer in this button maker.
  • Pressing with a hard slam instead of a steady pull. The metal lever does the crimping; a smooth pull keeps the edge even.

How to work a button maker: the short version

  1. Pick the size and fit the mold.
  2. Cut the design with the circle cutter on the A5 mat.
  3. Load the shell, design and clear cover, then pull the lever.
  4. Set the pin back on the other side and pull the lever again.
  5. Lift the finished button out and check the edge.

FAQ: lasers and CNC

What sizes does a button maker make?

This kit makes 3 sizes: 1 inch, 1.25 inch and 2.25 inch, or 25 mm, 32 mm and 58 mm, with 3 sets of interchangeable molds. Pick the size, then cut the design to match.

What paper should I use for small buttons?

For 25 mm and 32 mm buttons, use thicker pattern paper, slightly thicker than A4 paper, or use two layers of paper. Thicker paper holds its shape in the press and keeps small buttons crisp.

How many button parts does the kit hold?

The kit holds 300 sets of button parts, 100 of each size, so you can press buttons in any of the 3 sizes without ordering more parts.

Can I use the button maker as a magnet maker?

Yes. The kit listing says the set works as a magnet making machine as well as a pin maker. The press is the same; the back part is a magnet instead of a pin.

What should I do if a button comes out loose?

Check the order of the parts and the size of the cut: the shell goes in face down, then the design, then the clear cover, and the cut must match the mold. Pull the lever for the front of the button before setting the pin back, and use a steady pull: a hard slam can shift the parts.

Do I need the shim washer?

No. Do not put the shim washer in this button maker. The listing warns against it.

Related: the button maker vs badge maker guide, our best custom badge maker picks, our best A5 cutting mat picks, our best cutting mat for paper crafts picks and our craft machines hub.

More buying guides

Craft Machines ·

Button Maker Troubleshooting: Common Fixes

Button maker troubleshooting starts with matching the die to the button, cutting the fabric to the stated size, and setting the press height before…