How to Use Acetone to Smooth 3D Prints
How to use acetone to smooth 3D prints, with ventilation and fire safety covered, the smoothing steps, and pure acetone picks compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
MAXTITE Acetone 32 Fl Oz (Pack of 4)9.5/10View on Amazon - 2
100% Pure Crown Acetone Solvent Cleaner9.5/10View on Amazon
Layer lines on a fresh print catch the light and leave a part looking unfinished, and that is the problem how to use acetone to smooth 3d prints answers: acetone softens the outer surface so the lines flow into a smoother finish. This guide covers the setup, the smoothing step and the drying step, with ventilation and fire safety handled before any acetone comes out, and the acetone picks below supply the solvent for the job.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

MAXTITE Acetone 32 Fl Oz (Pack of 4)
100% pure acetone in four 32 fl oz bottles, 1 gallon total, for fast-evaporating degreasing and surface prep.
Pros
- 100% pure acetone for strong solvent action
- Four 32 fl oz bottles, 1 gallon total, for shop stock
- Fast-evaporating, residue-free formula for surface prep
- Dissolves oils, grease, silicone, resin and adhesive residues
Cons
- No gloves included in the pack
- No warranty term is stated
- 6.6 lb case to store and carry
- Four bottles take more shelf space than a small bottle

100% Pure Crown Acetone Solvent Cleaner
100% pure acetone in a 16 oz bottle with protective gloves included, for fast-evaporating cleaning and surface prep.
Pros
- 100% pure acetone for strong solvent action
- Protective gloves included for safer handling
- 16 oz bottle is easy to handle and store
- Fast-evaporating, residue-free results
Cons
- 16 oz is less acetone than the 1-gallon 4-pack case
- No warranty term is stated
- No spare bottle in the box when the 16 oz runs out
- Fast-evaporating formula means the bottle must stay capped between uses
How to use acetone to smooth 3d prints
Acetone smoothing works on ABS prints: the solvent softens the outer skin of the print so the ridges left by each layer flow together into a glossier surface. The print needs a surface the solvent can soften, a container that holds the vapor, and a dry place to rest while the finish sets. Work in a space with fresh air moving through it, away from flames, sparks and heat, and wear gloves whenever acetone is open. The rest of this guide walks through the setup, the smoothing pass and the drying check in order.
Ventilation and fire safety before you start
Acetone evaporates fast and its vapor catches fire easily, so ventilation and fire safety come before the print goes anywhere near the solvent. Work outdoors or in a space with air moving through it, and keep the work away from flames, sparks, heaters and any tool that throws sparks. Keep the acetone bottle capped when it is not in use, and keep the bottle away from heat. Wear gloves when you handle the solvent or the print, and wash your hands after the job. If the air smells strongly of solvent, stop and move the work to a space with more airflow.
Smooth the print in stages
Set the print on a small stand inside a container with a lid, and put a small amount of acetone in the bottom of the container without letting the liquid touch the print. Close the lid so the vapor can reach the surface, and check the print often. The lines soften from the outside in, so lift the lid and look at the surface between checks, then close the lid again if the lines still show. Stop when the surface looks smooth and glossy, and take the print out with gloves. A brush can also carry a thin film of acetone over a small area, but it leaves marks where the brush stops, so vapor gives the more even finish.
Let the print dry and check the finish
Set the print on a clean surface in ventilated air and leave it alone until the surface feels dry and firm. The finish keeps changing while the solvent leaves the surface, so do not handle the print or set anything on it until it has dried. Once dry, check the print in good light and look for soft spots, drips or areas where the lines still show. Another pass can smooth a spot an earlier pass missed, but each pass softens the surface again, so stop while the detail still reads clearly.
The acetone
Acetone does the smoothing, so the picks below cover the solvent itself and the gloves for handling it.
FAQ: lasers and CNC
Which prints can acetone smooth?
Acetone smoothing suits ABS prints, where the solvent can soften the surface and let the layer lines flow smooth. Check the filament type before you start, and try the method on a spare print from the same spool when you can. Prints in other plastics that acetone does not soften need a different finishing method.
Can I brush acetone on a print instead of using vapor?
Yes, a brush can carry acetone over a small area, and the solvent softens the surface where it touches. Brushing leaves marks where each stroke stops, so it suits small spots and edges rather than a whole print. Vapor reaches the whole surface at once and gives the more even finish.
How do I store acetone between jobs?
Keep the bottle capped and upright in a cool place away from flames, sparks and heat, and keep it where it will not tip over. The MAXTITE case holds four 32 fl oz bottles, 1 gallon total, so a shop can keep sealed bottles on the shelf. Keep acetone away from any source of ignition.
Do I need gloves when I handle acetone?
Yes, wear gloves whenever acetone is open or you handle a print that has just been smoothed. The OMNI DEPOT bottle includes protective gloves that reduce direct skin contact during use, which covers longer or repeated tasks. Wash your hands after the job even when you wore gloves.
What size acetone bottle should I buy?
Match the bottle to the size of the job. The OMNI DEPOT bottle holds 16 oz and suits small prints and occasional smoothing, with gloves in the box. The MAXTITE case holds four 32 fl oz bottles, 1 gallon total, and suits a shop that smooths prints often. Each bottle holds 100% pure acetone with a fast-evaporating formula.
Related: the 3D printer hub, 3D printer filament types and ABS vs ASA filament. Also see best 3D print filler primer spray..




