How to Cut Carbon Fiber: Tools and Methods
Cut carbon fiber with a fine blade made for the material and a guide that holds the tube steady, then check the edge after the cut.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Park Tool Carbon Cutting Saw Blade9.6/10View on Amazon - 2
Pawfly Bike Saw Guide with 1-1/8" Carbon Headset9.6/10View on Amazon
How to cut carbon fiber starts with the right blade and a steady hold: mark the cut, clamp the tube so it cannot move, and saw with light, steady strokes until the blade passes through. The Park blade’s listing states its super fine edge prevents damage to the carbon weave either side of the cut, and a saw guide holds the tube steady so the cut stays on the line. The sections below walk through each step, then show the tools that handle the cut.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Park Tool Carbon Cutting Saw Blade
A 12 in tungsten steel coated hacksaw blade made for cutting carbon fiber handlebars and seat masts, with a super fine edge that prevents damage to the weave either side of the cut.
Pros
- Tungsten steel coated blade made for cutting carbon fiber
- Super fine edge prevents damage to the carbon weave either side of the cut
- Fits the Park SAW-12 and many other 12 in hacksaws
- Listed as designed for safe and clean cutting of carbon parts
Cons
- Warranty states Limited Warranty with no term given
- Blade only; needs a 12 in hacksaw frame to use
- The listing states no uses beyond carbon bike parts
- Tooth count is not stated

Pawfly Bike Saw Guide with 1-1/8" Carbon Headset
An adjustable saw guide for steel, carbon fiber and aluminum alloy tubes from 0.6 to 1.45 in, with a T-handle, a vise-grip base and 5 headset spacers.
Pros
- Adjustable from 0.6 to 1.45 in (15 to 37 mm) for steel, carbon fiber and aluminum alloy tubes
- Thickened base grips in a bench vise to stop movement during tube cutting
- Knurled T-handle holds the tube in place
- Includes 1-1/8 in headset spacers in 5 thicknesses: 3, 5, 10, 15 and 20 mm
Cons
- No warranty term is stated
- Needs a bench vise to hold the base
- Works only with saw blades under 0.07 in (2 mm) thick
- Spacer set is for 1-1/8 in headsets only
How to cut carbon fiber
Mark the cut line around the tube so you can see it from every side. Clamp the tube in the saw guide and grip the guide in a bench vise, then check that the tube cannot move before you start. Use a blade made for carbon fiber.
Saw with light, steady strokes and let the blade do the work. Do not force the blade or twist it in the cut. When the blade passes through, lift the tube out of the guide and check the edge for loose fibers.
Pick a blade made for carbon fiber
The Park Tool blade (on Amazon) in this guide is a 12 in tungsten steel coated hacksaw blade made for carbon fiber, with a super fine edge that the listing states prevents damage to the carbon weave either side of the cut. It fits the Park SAW-12 and many other 12 in hacksaws. Pick a blade the listing states is made for carbon fiber, and check that it fits your hacksaw frame before you start.
Hold the tube steady with a saw guide
The Pawfly guide (on Amazon) holds steel, carbon fiber and aluminum alloy tubes from 0.6 to 1.45 in (15 to 37 mm). Rotate the T-handle to hold the tube, and grip the thickened base in a bench vise so the guide cannot move during the cut. The frame is reinforced aluminum alloy with stainless steel components, and the knurled T-handle gives grip and control.
The guide also includes 1-1/8 in carbon fiber headset spacers in 5 thicknesses, 3 mm, 5 mm, 10 mm, 15 mm and 20 mm, for handlebar height setup. Use it with saw blades under 0.07 in (2 mm) thick.
Dust and the workspace
Cut where air moves, wear eye protection and a dust mask while you saw, and clean up dust after the cut. Keep the work area clear, and never cut near an open flame.
Gear for cutting carbon fiber
The blade makes the cut and the guide holds the tube steady while you saw, so these 2 tools cover the cutting step and the holding step.
FAQ: lasers and CNC
What blade cuts carbon fiber?
The Park Tool CSB-1 is a 12 in tungsten steel coated hacksaw blade made for carbon fiber, with a super fine edge that the listing states prevents damage to the carbon weave either side of the cut. It fits the Park SAW-12 and many other 12 in hacksaws.
How do I keep the cut straight on a carbon tube?
Hold the tube in a saw guide and grip the guide in a bench vise. The Pawfly guide holds tubes from 0.6 to 1.45 in (15 to 37 mm) and its thickened base grips in a vise to stop movement during the cut.
What size tube does the Pawfly guide fit?
Tubes from 0.6 to 1.45 in (15 to 37 mm), in steel, carbon fiber and aluminum alloy. The guide is made for fork tubes, steerer tubes, seatposts and handlebars on road, mountain and hybrid bikes.
Can I use a regular hacksaw blade on carbon fiber?
The listing here for carbon fiber is the Park Tool blade, with a super fine edge made for the material. The listing states no comparison with standard blades, so match the blade to the material the listing names.
What spacers come with the Pawfly guide?
A 1-1/8 in carbon fiber headset spacer set in 5 thicknesses: 3 mm, 5 mm, 10 mm, 15 mm and 20 mm, for handlebar height customization.
Related: the CNC tooling hub and CNC router bits for carbon fiber. Also see the laser engraver hub.




