Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

DTF Transfer Size Guide: Common Sizes for Shirts and Crafts

A DTF transfer size guide that matches film width and length to the design, with four DTF films compared for shirts and crafts.

DTF Transfer Size Guide: Common Sizes for Shirts and Crafts
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1CenDale DTF Transfer Film Roll 13"x 65.6ftCenDale DTF Transfer Film Roll 13"x 65.6ft9.7/10View on Amazon
  2. 2Yitentek DTF Roll | A3+ DTF Transfer RollYitentek DTF Roll | A3+ DTF Transfer Roll9.7/10View on Amazon
  3. 3DTF Transfer Film Roll 13" x 328ft,Double SidedDTF Transfer Film Roll 13" x 328ft,Double Sided9.6/10View on Amazon
  4. 4CenDale DTF Transfer Film 8.5"x14"CenDale DTF Transfer Film 8.5"x14"9.6/10View on Amazon

A dtf transfer size guide starts with the garment in front of you, not with the roll on the shelf. Measure the print area, match the design to that space, then pick film wide enough to hold the design with room to spare. This guide explains how film sizes relate to design sizes, how to measure a shirt before printing, and which DTF films below fit each kind of job.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Size note

Film sizes in this guide come from the listings. Measure the garment and compare with the listed widths before ordering.

CenDale DTF Transfer Film Roll 13"x 65.6ft

CenDale DTF Transfer Film Roll 13"x 65.6ft

CenDale9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13 in wide DTF film roll, 65.6 ft long, matte print side with a glossy reverse, hot and cold peel, with an 18 months warranty.

Pros

  • 13 in wide roll, 65.6 ft long, for wide designs and repeat runs
  • 5 layer coating for ink absorption and fuller prints, per the maker
  • Hot and cold peel, with a listed press of 10 to 15 seconds at 266 to 320 °F
  • 18 months warranty stated in the listing

Cons

  • 65.6 ft is the shorter roll here; the other rolls run 328 ft
  • Roll format needs a roll-enabled printer, which the listing states
  • Needs a DTF printer, DTF ink and DTF powder, which the listing states are required
  • No stated sheet option in this listing for makers who want fixed sizes
Yitentek DTF Roll | A3+ DTF Transfer Roll

Yitentek DTF Roll | A3+ DTF Transfer Roll

Yitentek9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13 in wide DTF film roll, 328 ft long, double-sided matte, with hot, cold and warm peel and a 12-month free replacement.

Pros

  • 328 ft roll in 13 in width for long print runs
  • 75μm film with an anti-static coating for clean powder shaking
  • Hot, cold and warm peel in a single film
  • Press listed at 140 to 160 °C for 10 to 15 seconds

Cons

  • Returns within 30 days only for unopened, defective or unsatisfactory products
  • Matte only; no glossy option in this listing
  • No stated press temperature in °F, only 140 to 160 °C
DTF Transfer Film Roll 13" x 328ft,Double Sided

DTF Transfer Film Roll 13" x 328ft,Double Sided

imtfzct9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 13 in wide glossy DTF film roll, 328 ft long, double-sided, with hot and cold peel and a 2 Year Manufacturer warranty.

Pros

  • 328 ft of glossy film for bright prints
  • Double-sided glossy printing with good ink absorption
  • Hot and cold peel, with a listed press of 10 to 15 seconds at 266 to 320 °F
  • 2 Year Manufacturer warranty stated

Cons

  • Glossy only; no matte option in this listing
  • No stated sheet option; roll only
  • No stated pack count beyond the single roll
CenDale DTF Transfer Film 8.5"x14"

CenDale DTF Transfer Film 8.5"x14"

CenDale9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

60 sheets of 8.5 in x 14 in double-sided DTF film, 140gsm matte, hot and cold peel, with an 18 months warranty.

Pros

  • 60 sheets in a fixed 8.5 in x 14 in size, ready to feed
  • Hot peel with a listed press of 6 to 10 seconds at 266 to 320 °F
  • 140gsm matte film with a 5 layer coating
  • 18 months warranty stated in the listing

Cons

  • Sheet size caps design width at 8.5 in
  • No roll option in this listing for longer designs
  • The DTF sublimation hack works only on white fabrics, per the listing
  • 60 sheets run out sooner than a roll on repeat jobs

DTF Transfer Size Guide: Common Design Sizes

Design size follows garment size. A small chest print sits high on the chest, a full front print covers the middle of the shirt, and a sleeve print stays narrow. Each placement needs film at least as wide as the design, so the film width sets the widest design the roll or sheet can hold.

The rolls in this guide are 13 in wide, while the sheets are 8.5 in x 14 in. A design wider than 8.5 in needs a roll, while a design that fits inside 8.5 in x 14 in can use a sheet. Roll length matters for repeat work: the rolls here run 65.6 ft or 328 ft, and the longer roll suits shops that print the same design across many shirts.

Think in placements, not in fixed sizes. Measure the chest width, the space below the collar, and the hem, then compare those spans with the film on hand. A design that fits the film with room around the edges presses cleanly and peels without catching the film edge. For film options beyond size, see the best DTF transfer film guide and the DTF transfer film vs heat transfer paper comparison.

How to Measure a Shirt Before You Print

Lay the shirt flat and smooth out folds before measuring. Measure across the chest from side seam to side seam, then measure from the collar down to the hem. Those spans show the print area the shirt offers.

Mark the center of the chest with a fold or a light crease, then center the design on that mark. Leave space below the collar and above the hem so the print sits on flat fabric and the heat press closes evenly. For a pocket print or a sleeve print, measure the pocket or the sleeve the same way and keep the design inside it.

Measure each shirt size in the batch, since sizes vary across a run. A design sized for the smallest shirt in the batch fits every shirt in it, while a design sized for the largest shirt may crowd a smaller one.

Roll or Sheets: Picking Film by Job Size

Rolls suit repeat work. A 328 ft roll keeps the printer fed across many shirts without a roll change, while a 65.6 ft roll suits a shorter run of the same design. Rolls also let the maker cut film to the design size, so a narrow design wastes less film than a fixed sheet.

Sheets suit small batches and single designs. A pack of 60 sheets in 8.5 in x 14 in feeds like paper and needs no cutting, which keeps setup simple for a short run. Sheets also suit makers who print a few designs at a time and want to store the rest flat.

Match the format to the job, not the other way around. Long runs and wide designs point to rolls; short runs and small designs point to sheets. Either way, check the listed press settings before ordering: the CenDale and imtfzct rolls (on Amazon) list 266 to 320 °F for 10 to 15 seconds, the sheets list 266 to 320 °F for 6 to 10 seconds, and the Yitentek roll (on Amazon) lists 140 to 160 °C for 10 to 15 seconds. For pressing, see the Teflon sheet for DTF guide.

DTF Films for Every Size Job

The films below cover the sizes in this guide: wide rolls for full-front designs and long runs, and fixed sheets for small designs and short batches.

Common Mistakes to Avoid

  • Ordering film narrower than the design. Compare the design width with the film width first: a design wider than 8.5 in does not fit the sheets here.
  • Skipping the measurement. A shirt that looks standard can still vary, so measure the chest and the collar-to-hem span before printing.
  • Pressing outside the listed settings. The listings state 266 to 320 °F or 140 to 160 °C, with press times of 10 to 15 seconds for rolls and 6 to 10 seconds for sheets.
  • Forgetting the rest of the setup. The CenDale roll listing states that a DTF printer, DTF ink and DTF powder are needed alongside the film.
  • Assuming the sublimation hack works on any fabric. The CenDale sheets listing states that the DTF sublimation hack works only on white fabrics, since it lacks white ink.

DTF Transfer Size Guide: The Short Version

  1. Measure the print area on the shirt.
  2. Pick film at least as wide as the design.
  3. Choose a roll for long runs and sheets for short batches.
  4. Press at the settings the listing states.
  5. Peel hot or cold as the listing allows.

FAQ: lasers and CNC

What size DTF transfer fits a chest print?

It depends on the shirt. Measure the chest width and the space below the collar, then pick a design that fits inside those spans with room around the edges. A design wider than 8.5 in needs a roll, since the sheets here measure 8.5 in x 14 in.

Should a beginner start with rolls or sheets?

Sheets suit a short run: a pack of 60 sheets in 8.5 in x 14 in feeds without cutting and covers small designs. Rolls suit repeat work, since a 328 ft roll prints many shirts from a single roll.

How long is a DTF film roll?

The rolls in this guide run 65.6 ft or 328 ft. The CenDale roll is 65.6 ft long, while the imtfzct and Yitentek rolls are 328 ft long.

What press settings do these films list?

The CenDale roll and sheets list 266 to 320 °F, with 10 to 15 seconds for the roll and 6 to 10 seconds for the sheets. The imtfzct roll lists the same 266 to 320 °F for 10 to 15 seconds, and the Yitentek roll lists 140 to 160 °C for 10 to 15 seconds.

Can DTF film print on dark shirts?

The listings state that DTF film prints on light and dark fabrics, including cotton, polyester, denim, leather and blends. The CenDale sheets listing adds that the DTF sublimation hack works only on white fabrics, since it lacks white ink.

Related: the DTF transfer film sheets in A4 and A3, best DTF transfer film and DTF transfer film vs heat transfer paper. Also see the DTF transfer film in 13-inch rolls. Also see the DTF vs heat transfer vinyl.

More buying guides

Craft Machines ·

DTF Printer Sizes: Bed Dimensions Guide

This guide covers A3 and A3+ DTF printer sizes, and the size to pick is the one whose stated print width covers your largest…