Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Router Bit for Dado in Plywood (2026)

Four straight router bits for clean plywood dados, from a 23/32 in Freud bit on a 1/2 in shank to undersized sets that match the true thickness of plywood sheets.

Best Router Bit for Dado in Plywood (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Freud 12-150Best OverallFreud 12-1509.7/10View on Amazon
  2. 2Freud 89-660Best Undersized SetFreud 89-6609.6/10View on Amazon
  3. 3Hiltex Straight SetBest Straight Bit SetHiltex Straight Set9.6/10View on Amazon
  4. 4Aoranto Dado SetBest Undersized Carbide SetAoranto Dado Set9.4/10View on Amazon

A cabinet shelf should slide into its dado and sit flat, with no rattle and no gap along the edge. When the groove runs wide, the shelf wobbles and glue alone cannot fix the joint. When the groove runs narrow, the shelf needs force and the plywood veneer chips at the edge. The best router bit for dado in plywood cuts a groove that matches the sheet, so the joint goes together by hand and stays square through assembly.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall Freud 12-150: A 23/32 in double flute straight bit on a 1/2 in shank, with Freud TiCo carbide and a limited lifetime warranty. Check price on Amazon
  • Best Undersized Set Freud 89-660: Three bits that match the true thickness of 1/4, 1/2 and 3/4 in plywood, in a wooden shadowbox case, with a limited lifetime warranty. Check price on Amazon
  • Best Straight Bit Set Hiltex Straight Set: Four straight bits from 1/4 to 1/2 in diameter on 1/4 in shanks, with YG8 carbide and a labeled case for each bit. Check price on Amazon
  • Best Undersized Carbide Set Aoranto Dado Set: Four undersized diameters from 7/32 to 23/32 in on 1/4 in shanks, with solid carbide rated at 94.5 HRA. Check price on Amazon

Machines on the list

Freud 12-150: 23/32" (Dia.)

Freud 12-150: 23/32" (Dia.)

Freud9.7/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 23/32 in double flute straight bit on a 1/2 in shank, with a 1-1/4 in carbide height and Freud TiCo Hi-Density carbide for clean cuts in plywood and composites.

Pros

  • 23/32 in cutting diameter, the undersized size for 3/4 in plywood
  • 1/2 in shank, wider than the 1/4 in shanks on the sets here
  • Freud TiCo Hi-Density carbide, precision ground for clean cuts in solid wood, plywood and composites
  • Kickback reducing design, individually computer balanced

Cons

  • Sold as one bit, so other dado widths need separate bits
  • No storage case is stated in the listing
  • No maximum speed is stated in the listing
  • 1/2 in shank needs a router or table with a 1/2 in collet
Freud 89-660: 3 Piece Undersized Plywood Bit Set

Freud 89-660: 3 Piece Undersized Plywood Bit Set

Freud9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 piece undersized plywood bit set on 1/4 in shanks, with bits that match the true thickness of 1/4, 1/2 and 3/4 in plywood, in a wooden shadowbox case.

Pros

  • Bits match the true thickness of 1/4, 1/2 and 3/4 in plywood
  • Three diameters cover the 1/4, 1/2 and 3/4 in plywood sizes stated in the listing
  • Freud Perma-SHIELD coating
  • Includes a wooden shadowbox case for storage

Cons

  • 1/4 in shank on every bit, with no 1/2 in shank option
  • No flute count is stated in the listing
  • No carbide grade is stated in the listing
  • No maximum speed is stated in the listing
HILTEX Straight Router Bit Set

HILTEX Straight Router Bit Set

Hiltex9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4 piece straight bit set on 1/4 in shanks, with diameters from 1/4 to 1/2 in, YG8 carbide and a labeled case for each bit.

Pros

  • Four diameters from 1/4 to 1/2 in, for dados, grooves, rabbets and inlay channels
  • YG8 carbide edges on a hardened #45 carbon steel body
  • Rated for routers running at up to 16,000 RPM
  • Anti-kickback design with a balanced double flute cut

Cons

  • No warranty term is stated in the listing
  • 1/4 in shank on every bit, with no 1/2 in shank option
  • Standard diameters only, so undersized plywood needs a different bit
  • Each bit ships in its own case, so the set has no single storage box
Aoranto 4 Pieces Undersize Plywood Dado Bits 1/4"

Aoranto 4 Pieces Undersize Plywood Dado Bits 1/4"

Aoranto9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4 piece undersized plywood dado set on 1/4 in shanks, with cutting diameters of 7/32, 11/32, 15/32 and 23/32 in and solid carbide rated at 94.5 HRA.

Pros

  • Four undersized diameters from 7/32 to 23/32 in, for accurate grooves in undersized plywood
  • Solid carbide rated at 94.5 HRA, with 2400N/mm2 TRS and 7.40 SEVNB
  • Traceability code on each tool for full-process quality tracking
  • Suits engraving machines, table mount routers and CNC machining centers

Cons

  • No warranty term is stated in the listing
  • 1/4 in shank on every bit, with no 1/2 in shank option
  • No flute count is stated in the listing
  • No maximum speed is stated in the listing

Specs compared

Model HQ Score Shank Cutting diameter Flutes Carbide Set size Warranty
Freud 12-150 9.7/10 1/2 in 23/32 in 2 Freud TiCo Hi-Density 1 bit Limited lifetime
Freud 89-660 9.6/10 1/4 in Undersized for 1/4, 1/2, 3/4 in plywood Not stated Not stated 3 bits Limited lifetime
Hiltex Straight Set 9.6/10 1/4 in 1/4, 5/16, 3/8, 1/2 in 2 YG8 4 bits Not stated
Aoranto Dado Set 9.4/10 1/4 in 7/32, 11/32, 15/32, 23/32 in Not stated Solid carbide, 94.5 HRA 4 bits Not stated

Size and performance figures are the brand’s ratings quoted from listings on 22 November 2026.

How the picks are scored

Each bit is scored on performance, build, value, safety and warranty. A spec the listing does not publish scores nothing.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Freud 12-150 9.7 32 22 19 7 4
Freud 89-660 9.6 30 21 21 0 4
Hiltex Straight Set 9.6 29 21 21 7 0
Aoranto Dado Set 9.4 28 20 20 0 0

We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.

Why plywood dados need an undersized bit

Plywood sheets run thinner than the nominal size on the label, so a bit sold at the nominal diameter cuts a groove with slack in it. Undersized bits close that gap: the Freud 89-660 set and the Aoranto set are sized to the true thickness of the sheet, so the shelf meets the sides of the groove along its full depth. A snug dado holds the shelf square while glue sets, and the joint reads as a clean line from the front.

The straight bits here cut square-bottom grooves, which suit shelf housings, drawer dividers and cabinet carcasses. A double flute bit clears waste on the cut and leaves a flat floor, and the carbide edge keeps that floor clean across a run of parts.

How to choose the best router bit for dado in plywood

Match the bit to the plywood thickness

Start with the sheet, not the bit. The Freud 89-660 set matches the true thickness of 1/4, 1/2 and 3/4 in plywood, and the Aoranto set covers the same range with undersized diameters of 7/32, 11/32, 15/32 and 23/32 in. For a single thickness, the Freud 12-150 cuts a 23/32 in groove for 3/4 in plywood. The Hiltex set covers nominal diameters from 1/4 to 1/2 in for grooves in solid wood and sheet goods. The router bit sizes chart lays out diameter and shank pairings.

Shank size and router fit

The sets here run on 1/4 in shanks, which fit handheld routers, router tables and CNC machines. The Freud 12-150 runs on a 1/2 in shank, with a 2-7/8 in overall length, and suits a router or table with a 1/2 in collet. Check the collet before ordering: a 1/2 in shank will not seat in a 1/4 in collet.

Flutes and carbide

The Hiltex set and the Freud 12-150 are double flute bits, and the Hiltex maker pairs YG8 carbide edges with a hardened #45 carbon steel body. The Aoranto set states its carbide figures in full: AT03 ultra-fine grain solid carbide at 94.5 HRA, 2400N/mm2 TRS and 7.40 SEVNB. The Freud 89-660 states no carbide grade and no flute count, so the choice there rests on the undersized fit and the case.

Sets against a single bit

A set covers several groove widths with matched storage: the Hiltex set spans 1/4 to 1/2 in with a labeled case for each bit, and the Freud 89-660 set spans the plywood thicknesses with a wooden shadowbox case. A single bit suits a shop that cuts one groove width again and again, and the Freud 12-150 pairs that focus with a 1/2 in shank and a limited lifetime warranty.

Safety

Router bits spin fast and throw chips, so eye and ear protection and a clear work area matter on every cut. Seat the shank to the depth the maker marks: Hiltex laser-etches a line on each shank showing the minimum depth to insert the bit into the collet. Keep hands clear of the cut path, feed against the rotation of the bit, and switch the router off before adjusting the bit or clearing waste. Vent dust away from the work area

Project Match

Pair the pick with the project, using the materials and machines each listing states.

  • Cabinet carcasses and shelves in 3/4 in plywood: Freud 12-150, with a 23/32 in groove and a 1/2 in shank.
  • Drawer dividers and shelves across 1/4, 1/2 and 3/4 in plywood: Freud 89-660, with undersized bits for each thickness.
  • Furniture, drawer fronts, cabinet doors and shelves in HDU, laminate, MDF, veneered plywood, softwoods and hardwoods: Hiltex Straight Set.
  • Grooves in laminate, melamine, MDF and veneered plywood on a CNC machining center: Aoranto Dado Set.

FAQ: lasers and CNC

What size router bit cuts a dado in 3/4 in plywood?

A 23/32 in bit, the undersized size for 3/4 in plywood. The Freud 12-150 cuts a 23/32 in groove, and both undersized sets here include that size.

Should a dado bit have a 1/4 in or 1/2 in shank?

Either shank works when the collet matches it. The sets here run on 1/4 in shanks, while the Freud 12-150 runs on a 1/2 in shank. Match the shank to the collet on the router or table.

What is an undersized plywood dado bit?

A bit whose cutting diameter matches the true thickness of plywood, which runs thinner than the nominal size. The Aoranto set and the Freud 89-660 set both state that fit for accurate grooves.

Can a straight bit cut dados on a CNC machine?

Yes, when the listing states CNC use. The Hiltex set states use in CNC machines, the Aoranto set states CNC machining centers, and the Freud 12-150 states use in CNC routers.

How deep can a dado bit cut?

It depends on the bit. The Freud 12-150 states a cutting depth of 1-1/4 in, and the Hiltex set states cutting heights from 25/32 to 1-3/16 in. The Aoranto set and the Freud 89-660 set state no cutting depth.

Related: best dado bit for plywood, best 1/4 dado router bit, router bit sizes chart, router bit shank sizes and the CNC tooling hub.

More buying guides

Fiber Laser Engravers ·

Best Dado Bit for Plywood (2026)

Best dado bit for plywood: five router bits compared on diameter, shank and undersized fit, with the 4-bit plywood set ranked first.