Dado vs Rabbet Bit for CNC: Which One Should You Buy?
A dado bit and a rabbet bit for CNC cut in different places, and four bits show the difference in shank, diameter, cutting length and bearings.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SpeTool Upcut Spiral Router Bits Extra Long9.7/10View on Amazon - 2
Whiteside 1955 Multi Rabbet 1/2 Inch Shank Set9.6/10View on Amazon - 3
7Pcs Straight Router Bit Set 1/4 Shank9.6/10View on Amazon - 4
4 Pcs Rabbeting Router Bits Set 1/4 Inch Shank9.6/10View on Amazon
A shelf that needs a groove down the middle and a cabinet door that needs a stepped edge call for different cuts. The dado vs rabbet bit for CNC choice comes down to where the cut sits: a dado cuts a channel across the face of a board, while a rabbet bit cuts a shoulder along its edge.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: pick a dado bit for a groove across the face, for mortises, slots and dadoes; pick a rabbet bit for a shoulder along the edge. The SpeTool upcut spiral leads the dado side with a 2-inch cutting length, while the Whiteside multi rabbet leads the rabbet side with eight depths from flush trim to 1/2 inch.
Machines on the list

SpeTool Upcut Spiral Router Bits Extra Long
A solid carbide upcut spiral bit with a 1/2-inch shank, a 1/2-inch cutting diameter and a 2-inch cutting length for grooves, slots and dadoes.
Pros
- Solid carbide upcut spiral clears chips and reduces heat
- 2-inch cutting length with a 4-inch total length suits deep grooves
- 1/2-inch shank fits a 1/2-inch collet
- Stated for soft woods, hard woods, plywood, laminate, oak and MDF
Cons
- A single bit, so only one cutting diameter is offered
- 1/2-inch shank needs a 1/2-inch collet
- No bearings are stated
- Cutting diameter is fixed at 1/2 inch

Whiteside 1955 Multi Rabbet 1/2 Inch Shank Set
A multi rabbet set with a 1/2-inch shank, a 1-3/8-inch large diameter, eight bearings and eight depths from flush trim to 1/2 inch.
Pros
- Eight bearings give eight depths from flush trim to 1/2 inch
- 1-3/8-inch large diameter with a 1/2-inch cutting length
- Carbide-tipped cut with a hex wrench included
- Supplied in a durable hardened plastic case
Cons
- A single bit, so only one large diameter is offered
- 1/2-inch shank needs a 1/2-inch collet
- Cutting length is 1/2 inch
- No material list is stated

7Pcs Straight Router Bit Set 1/4 Shank
A seven-piece straight router bit set with a 1/4-inch shank, cutting diameters from 1/8 inch to 1/2 inch and C3 tungsten carbide blades.
Pros
- Seven bits cover cutting diameters from 1/8 inch to 1/2 inch
- Cutting heights of 1/2 inch, 3/4 inch, 1 inch and 1-3/16 inches
- C3 micro-grain tungsten carbide blades for a sharper edge
- Stated for chipboard, MDF, plywood and hardwood on CNC and handheld routers
Cons
- 1/4-inch shank only, so it fits no 1/2-inch collet
- Straight cut only, with no upcut spiral stated
- No bearings are stated
- Cutting heights differ across the seven bits

4 Pcs Rabbeting Router Bits Set 1/4 Inch Shank
A four-piece rabbeting router bit set with a 1/4-inch shank, six bearings and cutting heights of 1/8 inch, 1/4 inch, 3/8 inch and 1/2 inch.
Pros
- Six bearings in sizes from 1/2 inch to 1-1/8 inches
- Cutting heights of 1/8 inch, 1/4 inch, 3/8 inch and 1/2 inch
- High carbon steel with carbide tips for a longer-lasting edge
- Mandrels and bearings reduce vibration; Teflon coating minimizes chips and resin buildup
Cons
- 1/4-inch shank only, so it fits no 1/2-inch collet
- No cutting diameter is stated
- No total length is stated
- Bearings are shared across the four bits
Other machines to compare
Whiteside 470 Plywood Dado Set: Includes Solid CarbideCheck price on Amazon
1/4 Inch Upcut Spiral CNC Router Bit for WoodCheck price on Amazon
Extra Long 2" Cutting Length Compression Router BitCheck price on Amazon
Rabbet Router Bit Set 1/2 ShankCheck price on Amazon
Extra Long 4" Upcut CNC Router Bit 1/4" ShankCheck price on Amazon
CNC Spoilboard Surfacing Router Bit 1/4 Inch ShankCheck price on Amazon
Side by side
| Bit | HQ Score | Side | Shank | Cutting diameter | Cutting height | Bearings |
|---|---|---|---|---|---|---|
| SpeTool Upcut Spiral | 9.7/10 | Dado | 1/2 in | 1/2 in | 2 in | Not stated |
| Whiteside Multi Rabbet | 9.6/10 | Rabbet bit for CNC | 1/2 in | 1-3/8 in large diameter | 1/2 in | 8 bearings |
| SICWOOD 7-Piece Set | 9.6/10 | Dado | 1/4 in | 1/8 to 1/2 in | 1/2 to 1-3/16 in | Not stated |
| Mikniri Rabbet Set | 9.6/10 | Rabbet bit for CNC | 1/4 in | Not stated | 1/8 to 1/2 in | 6 bearings |
We give each product’s specs as its manufacturer rates them; listings read 23 October 2026.
Dado vs rabbet bit for CNC: the cut itself
A dado bit cuts a groove into the face of a board, so a shelf or a panel can sit inside the groove. The SpeTool bit is made for upcut grooves and slots, plunge mortises and dadoes, and the SICWOOD set is made for jointing, grooving and rabbets. A rabbet bit cuts a recessed shoulder along the edge, so one board can lap over another at a joint.
Shank, diameter and cutting length
The SpeTool bit and the Whiteside set use a 1/2-inch shank, while the SICWOOD set and the Mikniri set use a 1/4-inch shank. The SpeTool bit states a 1/2-inch cutting diameter, the Whiteside set states a 1-3/8-inch large diameter, and the SICWOOD set states cutting diameters from 1/8 inch to 1/2 inch. The Mikniri cutting diameter is not stated. The SpeTool bit states a 2-inch cutting length, the Whiteside set states a 1/2-inch cutting length, and the SICWOOD bits state cutting heights from 1/2 inch to 1-3/16 inches. See router bit shank sizes.
Bearings and rabbet depths
Bearings make a rabbet bit adjustable. The Whiteside set includes eight bearings and a hex wrench for eight depths, from flush trim to 1/2 inch, in 1/16-inch increments. The Mikniri set includes six bearings in sizes 1/2 inch through 1-1/8 inches, with cutting heights of 1/8 inch through 1/2 inch. The dado examples state no bearings.
Materials and machines
The SpeTool bit states soft woods, hard woods, plywood, laminate, oak and MDF, and use with a CNC router and a handheld router. The SICWOOD set states chipboard, MDF, plywood and hardwood, and use on a CNC machine and handheld routers. The Mikniri set states solid wood, particleboard, hardwood, plywood, MDF and softwood, and use with handheld, desktop and CNC routers.
Choose a dado bit if
- You need a groove across the face of a board, for a shelf, a panel or a slot.
- You want an upcut spiral that clears chips, as the SpeTool bit states.
- You want several groove widths in one set, as the SICWOOD set states.
Choose a rabbet bit if
- You need a shoulder along the edge of a board, for a joint or a recessed edge.
- You want to change the shoulder depth by changing a bearing.
- You want a set with a case and a hex wrench, as the Whiteside set states.
For more on spiral bits, see compression vs spiral router bit.
Router bits cut fast and throw chips. Wear eye protection and hearing protection, keep guards in place, and follow the maker’s manual for setup and alignment.
Project Match
- Grooves in plywood, laminate, oak and MDF: the SpeTool upcut spiral.
- Grooves in chipboard, MDF, plywood and hardwood at several widths: the SICWOOD set.
- Shoulder joints with eight depths from flush trim to 1/2 inch: the Whiteside set.
- Rabbet slots in solid wood, particleboard, hardwood, plywood, MDF and softwood: the Mikniri set.
FAQ: lasers and CNC
What rabbet depths does the Whiteside set cut?
Eight depths, in 1/16-inch increments: flush trim, 1/8 inch, 3/16 inch, 1/4 inch, 5/16 inch, 3/8 inch, 7/16 inch and 1/2 inch.
Which shank size do these bits use?
The SpeTool bit and the Whiteside set use a 1/2-inch shank, and the SICWOOD set and the Mikniri set use a 1/4-inch shank.
Can these bits run on a CNC router?
The SpeTool bit, the SICWOOD set and the Mikniri set each state use with a CNC router. CNC use is not stated for the Whiteside set.
What cutting diameters does the SICWOOD set include?
Seven diameters: 1/8 inch, 5/32 inch, 3/16 inch, 1/4 inch, 5/16 inch, 3/8 inch and 1/2 inch, with cutting heights of 1/2 inch, 3/4 inch, 1 inch and 1-3/16 inch.
What rabbet depths does the Mikniri set cut?
Four cutting heights: 1/8 inch, 1/4 inch, 3/8 inch and 1/2 inch, with 6 interchangeable bearings in sizes 1/2 inch, 5/8 inch, 3/4 inch, 7/8 inch, 1 inch and 1-1/8 inch.
Related: router bit shank sizes, compression vs spiral router bit and best 1/4 dado router bit.




