Best Flux for Soldering Jewelry
Liquid and borax fluxes for clean gold, silver and platinum joints, compared by form, size and application.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallBerkland Flux 8 fl oz9.7/10View on Amazon - 2
Best Liquid FluxAquiflux Silver Flux9.6/10View on Amazon - 3
Best Spray BottleMegaCast Aquiflux 8 oz9.6/10View on Amazon - 4
Best Borax PowderMAQIHAN Borax Flux9.6/10View on Amazon
A jewelry joint fails or holds on the flux as much as on the solder. The right flux strips oxides from the metal, lets solder flow into the seam and leaves a clean joint that needs little cleanup. This guide covers the best flux for soldering jewelry, from clear liquids for rings and chains to borax powder for melting and casting.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Berkland Flux 8 fl oz: Self-pickling liquid flux in 8 fl oz with a twist cap and a finger mister, for gold, silver and platinum. Check price on Amazon
- Best Liquid Flux Aquiflux Silver Flux: Low-residue clear liquid flux in 8 oz with a twist cap and spray combo for clean gold and silver joints. Check price on Amazon
- Best Spray Bottle MegaCast Aquiflux 8 oz: Self-pickling water-based flux in an 8 oz spray bottle, 275 ml, for gold, silver and platinum. Check price on Amazon
- Best Borax Powder MAQIHAN Borax Flux: 7.4oz borax powder for melting gold and silver and glazing crucibles. Check price on Amazon
Machines on the list

Berkland Self-Pickling Flux for Gold
Self-pickling liquid flux in 8 fl oz with a twist cap and a finger mister, for gold, silver and platinum joints.
Pros
- Self-pickling formula, so no separate pickle bath is needed
- Twist cap and finger mister for flexible application at the bench
- Made in the USA
- Cleans and protects metal surfaces during heating
Cons
- No brush applicator is included, only a twist cap and a finger mister
- Rinse with warm water after cooling, an extra step after each joint
- Liquid form suits soldering joints, not melting and casting work
- Warranty term is not stated on the listing

Aquiflux Silver Flux for Soldering Jewelry Twist
Low-residue liquid flux in 8 oz with a twist cap and spray combo, for clean gold and silver joints.
Pros
- Low-residue formula for clean joints
- Clear liquid keeps the solder joint visible
- Twist cap and spray combo for bench use
- Suits gold, silver and platinum work
Cons
- No brush applicator is included
- Liquid form suits joints, not melting and casting
- Joints need a separate pickle step after soldering
- 8 oz bottle suits bench use rather than high-volume work

Aquiflux Self Pickling Flux for Precious Metals
Self-pickling water-based flux in an 8 oz spray bottle, 275 ml, for gold, silver and platinum.
Pros
- Self-pickling formula, so no separate pickle bath is needed
- Clear liquid lets you see the solder joint while soldering
- Liquid flows into joints better than a paste
- Spray bottle applies flux to the joint
Cons
- Warranty term is not stated on the listing
- Yellow-green color is less clear than a clear liquid
- Spray only, with no twist cap option
- Liquid form suits joints, not melting and casting

MAQIHAN 7.4oz Borax Flux
7.4oz borax powder for melting gold and silver, glazing crucibles and soldering jewelry.
Pros
- Dissolves oxides and impurities during melting
- Glazes ceramic crucibles, per the maker
- Suits melting, casting and soldering in one powder
- Mixes with distilled water into a milky paste for application
Cons
- Powder needs mixing before use, unlike a ready liquid
- Powder form is less precise on small joints than a liquid
- Must stay dry in storage to keep working
- Professional use only, per the maker

Rosenthal Collection Borax Flux 5 MOL
1/2 LB borax casting flux in a resealable bag, for melting gold, silver and sterling.
Pros
- Resealable bag suits high-volume bench use
- Formulated for gold, silver and sterling
- Reduces oxidation and protects metal during the melt
- Maker states use by jewelers since 1926
Cons
- Powder form suits casting and melting more than fine joints
- No applicator is included in the bag
- Formulated for gold, silver and sterling only
- No spray or twist cap option for quick application
Other machines to compare
MG Chemicals 835-PX2 Flux Pen SolderingCheck price on Amazon
HARRIS SCPF4 Stay Clean Paste Soldering FluxCheck price on Amazon
Rosenthal Collection Borax Flux 5 MOLCheck price on Amazon
Megacast Handy Flux PasteCheck price on Amazon
JTS-FLUX Self Pickling Flux for Precious Metals Gold SilverCheck price on Amazon
Specs compared
| Flux | HQ Score | Size | Form | Metals | Application |
|---|---|---|---|---|---|
| Berkland Flux 8 fl oz | 9.7/10 | 8 fl oz | Liquid, self-pickling | Gold, silver, platinum | Twist cap, finger mister |
| Aquiflux Silver Flux | 9.6/10 | 8 oz | Liquid, low-residue | Gold, silver, platinum | Twist cap, spray |
| MegaCast Aquiflux 8 oz | 9.6/10 | 8 oz (275 ml) | Liquid, self-pickling | Gold, silver, platinum | Spray bottle |
| MAQIHAN Borax Flux | 9.6/10 | 7.4oz | Powder | Gold, silver | Crucible, melting |
| Rosenthal Borax Flux | 9.5/10 | 1/2 LB | Powder | Gold, silver, sterling | Casting, melting |
These numbers come straight from each maker’s listing and are rated, not measured by us (20 November 2026).
Best flux for soldering jewelry: how to choose
Start with the job. For a ring, chain or setting, a liquid flux flows into the seam and lets you watch the joint while you work. For melting scrap or casting, a borax powder dissolves oxides in the melt and glazes the crucible. The liquids here are all made for gold, silver and platinum, while the borax powders are made for gold and silver, with the Rosenthal borax also naming sterling.
Form decides how you apply it. A spray bottle covers a joint fast, a twist cap gives a measured drop, and a finger mister reaches a small setting. A powder needs water and mixing before it is ready, so it suits the melting bench more than a quick repair. Match the form to the joint, then check the size: the liquids here come in 8 oz or 8 fl oz bottles, and the borax powders come as 7.4oz or 1/2 LB.
Buying guide: flux for jewelry soldering
Liquid flux for joints
Liquid flux is the bench choice for rings, chains, settings and repair work. It flows into seams and settings, and a clear liquid lets you see the solder joint while you work. The Rosenthal Aquiflux is a low-residue clear liquid, so joints come out clean, while the Berkland and MegaCast liquids are self-pickling, so they clean as they flow. Pick a liquid when the joint is small and the seam must stay visible.
Borax powder for melting and casting
Borax powder is the melting-bench flux. It dissolves oxides and impurities in molten gold and silver, and the borate slag floats on the melt for easy separation. The MAQIHAN powder also glazes ceramic crucibles, and the Rosenthal borax comes in a resealable bag for studio use. Pick a powder when you melt, cast or pour, not when you join a fine chain.
Self-pickling flux
Self-pickling flux cleans and protects the metal while it heats, so there is no separate pickle bath after soldering. The Berkland flux and the MegaCast Aquiflux both make this claim, and both are made for gold, silver and platinum. After cooling, the Berkland flux rinses off with warm water and a brush if desired. If a flux does not call itself self-pickling, plan a pickle step after the joint cools.
Size and storage
The liquids here come in 8 oz or 8 fl oz bottles, a bench size that lasts through many joints. The borax powders come as 7.4oz or 1/2 LB, with the Rosenthal borax in a resealable bag. Borax must stay dry to keep working, so store the powder in a dry place with the bag sealed. Liquids live on the bench in their bottles, with caps closed between jobs.
Soldering needs ventilation, eye protection and a heat-proof surface. Work with the bench vented, keep flux and solder away from food and drink, and wash hands after handling. Lead solder is not for food-contact items. Keep borax powder dry and out of reach of children and pets.
Project Match
- Ring sizing and repair: Berkland Flux 8 fl oz or Aquiflux Silver Flux, both liquids for visible joints on gold, silver and platinum.
- Chain and setting work: MegaCast Aquiflux 8 oz, a self-pickling spray for gold, silver and platinum joints.
- Melting and casting: MAQIHAN Borax Flux or Rosenthal Borax Flux, both borax powders for gold and silver melts.
- Crucible glazing: MAQIHAN Borax Flux, stated for glazing ceramic crucibles.
How the scores add up
Each flux is scored on performance, build, value, safety and warranty, with the weights explained on our How We Pick page. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Berkland Flux 8 fl oz | 9.7 | 32 | 21 | 21 | n/a | 0 |
| Aquiflux Silver Flux | 9.6 | 30 | 21 | 21 | n/a | 0 |
| MegaCast Aquiflux 8 oz | 9.6 | 30 | 20 | 20 | n/a | 0 |
| MAQIHAN Borax Flux | 9.6 | 28 | 20 | 20 | n/a | 0 |
| Rosenthal Borax Flux | 9.5 | 27 | 19 | 20 | n/a | 0 |
Scores never fall under 9.2 or rise above 9.8. A machine’s spot between those limits is set purely by its point total. An unpowered accessory whose listing names no safety feature is scored without safety, out of 90.
FAQ: lasers and CNC
What flux is best for soldering gold jewelry?
A liquid self-pickling flux is the usual bench choice for gold joints. The Berkland flux and the MegaCast Aquiflux are both self-pickling liquids made for gold, silver and platinum, and the Rosenthal Aquiflux is a low-residue clear liquid for the same metals. Borax powder suits melting gold, not joining a fine chain.
Is borax flux good for jewelry soldering?
Borax flux suits melting and casting more than fine joints. It dissolves oxides in molten gold and silver and glazes crucibles, which is why both borax powders here are sold as casting flux. For a ring or chain joint, a liquid flux flows into the seam and keeps the joint visible.
What is self-pickling flux?
Self-pickling flux cleans and protects metal surfaces during heating, so no separate pickle bath is needed after soldering. The Berkland flux and the MegaCast Aquiflux both make this claim. After cooling, rinse with warm water and brush if desired.
How much flux do I use on a joint?
Apply a small amount to clean metal surfaces, as the Berkland directions state, then heat and apply solder. A thin coat that covers the seam is enough, and extra flux does not make a stronger joint. Rinse the joint with warm water after it cools.
Related: best soldering torch, best jewelry pliers set, best soldering mat, best jewelry polishing cloth and the soldering hub.




