Best Desoldering Pump (2026): 5 Picks for Solder Removal
Five desoldering pumps for through-hole rework and solder removal, compared by suction design, nozzle sizes, heat rating and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallYIHUA 929D-V9.7/10View on Amazon - 2
Best Manual PumpENGINEER SS-039.6/10View on Amazon - 3
Best KitHuxvonl Pump Kit9.6/10View on Amazon - 4
Best 3-PackTeenitor 3-Pack Pump9.4/10View on Amazon
A solder joint that will not let go is where most rework jobs begin: a part to swap on a board, a bridge to clear between two pins, a keyboard switch to lift out without cooking the pads around it. The best desoldering pump for that work pulls melted solder out in a clean pull and leaves the hole open for the next part. This guide compares the pumps on the suction design, the nozzle sizes, the heat rating and the warranty each listing states, so the pick matches the bench work ahead.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall YIHUA 929D-V: An electric iron and pump in one tool, with 1.0 mm and 1.2 mm nozzles and a 12-month coverage. Check price on Amazon
- Best Manual Pump ENGINEER SS-03: Made in Japan with an aluminum body, a silicone nozzle and a stated 350°C heat rating. Check price on Amazon
- Best Kit Huxvonl Pump Kit: A manual pump plus a solder wick, with a self-cleaning design and a 1 year warranty. Check price on Amazon
- Best 3-Pack Teenitor 3-Pack Pump: Three one-handed pumps in one pack for the bench, the toolbox and a spare. Check price on Amazon
Machines on the list

YIHUA 929D-V Electric Desoldering Soldering Iron
An electric desoldering iron with the pump built in, a fixed temperature, two nozzle sizes and a 12-month manufacturer coverage.
Pros
- Iron and pump in one tool for single-handed, continuous desoldering
- Two interchangeable nozzles, 1.0 mm and 1.2 mm, for different through-hole sizes
- Heat deflector keeps excess heat off the hand during continuous work
- Scrap solder tube lifts out for cleaning, and the tool is reusable
Cons
- Temperature is fixed and non-adjustable
- Needs 3 to 5 minutes of preheat before normal heating
- Runs on 110-127V with a US plug, so it needs a mains outlet
- Nozzle must cool completely before changing

Solder Sucker Desoldering Pump Tool Kit with Gift
A manual aluminum pump bundled with a solder wick, with a tension spring, self-cleaning design and a 1 year manufacturer warranty.
Pros
- Includes a solder wick for cleaning residue the pump leaves behind
- Upgraded tension spring gives instant suction for fast removal
- Self-cleaning design resists solder residue and blockages
- One-touch thumb reset for one-handed use
Cons
- Needs a separate soldering iron
- The included solder wick is a consumable that runs out with use
- No spare tips are included beyond the wick
- Suction strength is fixed by the spring, with no adjustment

ENGINEER Solder Sucker Professional Grade Aluminum
A made-in-Japan aluminum pump with a silicone nozzle, spring-loaded suction and a self-cleaning shaft, rated heat resistant to 350°C.
Pros
- Silicone nozzle sits close to the iron tip for precise placement
- Spring-loaded suction clears melted solder with less residue
- Heat resistant to 350°C for direct contact with the iron
- Self-cleaning shaft keeps continuous work going without clogging
Cons
- No warranty term is stated
- Needs a separate soldering iron, unlike the integrated YIHUA 929D-V
- No solder wick is included
- Only two silicone tube sizes are included

Solder Sucker Tool No Clog Silicone-Tip Manual
A manual CNC-machined aluminum pump with a silicone tip rated to 350 °C, self-cleaning reset and eight replacement tips.
Pros
- Eight replacement tips are included for long use
- Silicone tip endures up to 350 °C and molds to joints
- Self-cleaning reset ejects solder waste on every reset
- No batteries, cords or filter changes, with a quick-release mechanism
Cons
- At 6.52 in it is shorter than the Huxvonl pump and the YIHUA iron
- Needs a separate soldering iron
- No solder wick is included
- Cleaning needs grease applied to internal parts after each clean

Teenitor Solder Sucker Desoldering Vacuum Pump
Three one-handed manual pumps in one pack, lightweight and compact, for bench or toolbox desoldering.
Pros
- Three pumps in one pack for the bench, the toolbox and a spare
- One-handed use with a thumb reset
- Lightweight and compact at 0.2 lb
- Non-slip handle for control during desoldering
Cons
- No warranty term is stated
- No solder wick or spare tips come with the pack
- All three pumps are the same size, so the pack offers no smaller option for tight boards
- Needs a separate soldering iron
Specs compared
| Model | HQ Score | Type | Length | Nozzle / Tips | Heat rating | Warranty |
|---|---|---|---|---|---|---|
| YIHUA 929D-V | 9.7/10 | Electric iron and pump | 10.24 in | 1.0 and 1.2 mm nozzles | Not stated | 12 months |
| Huxvonl Pump Kit | 9.6/10 | Manual pump and wick | 7.0 in | Not stated | Heat-resistant body | 1 year |
| ENGINEER SS-03 | 9.6/10 | Manual pump | 153 mm | 2 silicone tubes | 350°C | Not stated |
| VIRALLOY SS-786 | 9.6/10 | Manual pump | 6.52 in | 8 replacement tips | 350 °C | Not stated |
| Teenitor 3-Pack Pump | 9.4/10 | Manual pump, 3-pack | Not stated | Not stated | Not stated | Not stated |
We give each product’s specs as its manufacturer rates them; listings read 19 November 2026. Length is the stated body length; heat rating is the highest temperature the maker states for the nozzle or body.
What the listings tell you, and what they leave out
We read 5 desoldering pump listings for this guide. Only 2 stated a warranty term, and only 2 stated a heat rating in degrees. Only 1 is electric; the other 4 are manual spring-loaded pumps. Nozzle sizes are stated for 1 of the 5, and 1 listing gives two different lengths for the same pump.
The gaps matter most on heat and fit. A manual pump needs a separate iron, and the iron tip has to sit close to the nozzle for the suction to catch the melt. Where a listing states a heat rating, it is 350 degrees; where it does not, the maker calls the body heat resistant without a number.
Buying guide: choosing the best desoldering pump
Manual pump or electric iron
A manual pump is a spring-loaded tube: heat the joint with a separate iron, place the nozzle, press the trigger. The YIHUA 929D-V is the only electric pick here, with a fixed temperature and a preheat of 3 to 5 minutes. The other 4 need an iron of their own. Choose electric when the bench sees joint after joint; choose manual when the iron already on the bench does the heating.
Nozzle and tip sizes
The YIHUA 929D-V ships with 1.0 mm and 1.2 mm nozzles for different through-hole sizes. The ENGINEER SS-03 ships with 50 mm silicone tubes in 4 mm and 3 mm outer diameter. The VIRALLOY SS-786 ships with 8 replacement tips and a silicone tip that molds to joints. The Huxvonl pump and the Teenitor pack state no nozzle size.
Heat rating
The ENGINEER SS-03 is rated heat resistant to 350°C, and the VIRALLOY SS-786 silicone tip endures up to 350 °C. The Huxvonl pump calls its aluminum alloy body heat resistant without giving a degree figure. The YIHUA 929D-V and the Teenitor pack state no heat rating.
What comes in the box
The Huxvonl kit adds a solder wick for residue the pump leaves behind. The VIRALLOY SS-786 adds 8 replacement tips. The ENGINEER SS-03 adds 2 silicone tubes. The Teenitor pack holds 3 pumps. The YIHUA 929D-V adds a cleaning pin and a second nozzle. A wick and spare tips run out, and a pack of pumps does not replace them.
Cleaning and upkeep
The ENGINEER SS-03 has a built-in self-cleaning shaft, and the Huxvonl pump has a self-cleaning design that resists residue and blockages. The YIHUA 929D-V lifts its scrap solder storage tube out for cleaning and needs its cleaning pin used regularly. The VIRALLOY SS-786 ejects solder waste on every reset and needs the nozzle unscrewed, the spring removed and grease applied to internal parts after cleaning.
Desoldering works with a hot iron and melted solder. Work on a heat-proof surface, wear eye protection, and vent the workspace when solder smokes. Lead solder is not for food-contact items. Keep fingers clear of the nozzle and the iron tip, and let a nozzle cool completely before changing it.
Project Match
- Through-hole desoldering, joint after joint: YIHUA 929D-V, with the iron and pump in one tool and 1.0 mm and 1.2 mm nozzles.
- PCB rework, keyboard modification and home appliance repair: Huxvonl Pump Kit, with a solder wick for residue.
- Electronics repair on the go: VIRALLOY SS-786, manual with no power needed and 8 replacement tips.
- Bench, toolbox and spare: Teenitor 3-Pack Pump, 3 pumps in one pack.
- Close work with the iron tip: ENGINEER SS-03, with a silicone nozzle that sits close to the iron tip.
How the scores add up
Each pump is scored out of 10 on performance, build, value, safety and warranty. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| YIHUA 929D-V | 9.7 | 32 | 21 | 20 | 8 | 3 |
| Huxvonl Pump Kit | 9.6 | 29 | 20 | 21 | 7 | 3 |
| ENGINEER SS-03 | 9.6 | 32 | 22 | 20 | 8 | 0 |
| VIRALLOY SS-786 | 9.6 | 30 | 21 | 21 | 8 | 0 |
| Teenitor 3-Pack Pump | 9.4 | 26 | 18 | 21 | 0 | 0 |
Point totals are scaled so the weakest reads 9.2 and the strongest 9.8, with everything between kept in order.
FAQ: lasers and CNC
What is a desoldering pump used for?
A desoldering pump, also called a solder sucker or soldering remover, pulls melted solder off a joint so a part can be lifted out or a hole cleared for the next part. The YIHUA 929D-V listing describes it for through-hole components and removing excess solder and solder bridges.
Do I need an electric desoldering iron or a manual pump?
An electric iron heats and sucks in one tool, so it suits joint after joint without changing grip. A manual pump needs no power and no outlet, but it needs a separate iron.
What nozzle size do I need for through-hole desoldering?
Match the nozzle to the hole: the YIHUA 929D-V ships with 1.0 mm and 1.2 mm nozzles for different through-hole sizes. The ENGINEER SS-03 ships with silicone tubes in 4 mm and 3 mm outer diameter.
How do I clean a desoldering pump?
Follow the maker’s own routine. The YIHUA 929D-V lifts its scrap solder storage tube out for cleaning and needs its cleaning pin used regularly. The VIRALLOY SS-786 ejects solder waste on every reset; for a full clean, unscrew the nozzle, remove the spring, clean the cylinder with cotton swabs and apply grease to internal parts.
Can a desoldering pump damage a circuit board?
The Huxvonl pump states its self-cleaning design works without scratching fragile circuit boards. Place the nozzle on the melted joint, with the iron tip close to the nozzle, so the suction catches the melt.
Related: the electronics making hub, soldering temperature, and the best soldering iron for beginners. Also see our best fume extractor for soldering.




