Best Soldering Iron for Pcb Work (2026): 5 Picks for Clean Joints
Five irons and kits for PCB work, compared by power, temperature range, tips and the extras that keep joints clean.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallEOOKU 60W Auto Feed9.6/10View on Amazon - 2
Best KitANBES 60W Kit9.6/10View on Amazon - 3
Best Heavy DutyWeller W100PG 100W9.4/10View on Amazon - 4
LCD PickQ-MING 80W LCD9.5/10View on Amazon - 5
Kit PickQ-MING 60W Kit9.4/10View on Amazon
A board that will not take solder turns a small repair into a long evening. Pads lift, joints go dull and cold, and a part that should sit flat wobbles on its legs while the iron cools between joints. The best soldering iron for pcb work keeps heat where the joint needs it, holds a tip that fits the pad, and rests safely on the bench between joints, so the work moves from pad to pad without fuss.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall EOOKU 60W Auto Feed: 60W auto-feed iron with an LCD display, a 15-second heat-up and a 180-500°C range for one-handed PCB joints. Check price on Amazon
- Best Kit ANBES 60W Kit: 60W kit with 5 tips, a 200-450°C range and a 14-in-1 set that covers desoldering and board repair. Check price on Amazon
- Best Heavy Duty Weller W100PG 100W: 100W heavy-duty iron with a CT6F7 tip, rated at 700 degrees for larger joints. Check price on Amazon
- LCD Pick Q-MING 80W LCD: 80W LCD iron with 5 tips, a stand and solder wire for bench work. Check price on Amazon
- Kit Pick Q-MING 60W Kit: 60W kit with 5 tips and adjustable temperature for general board work. Check price on Amazon
Machines on the list

EOOKU Soldering Iron gun Kit,60W Auto Feed
A 60W auto-feed iron with an LCD display, a 15-second heat-up, a 180-500°C range and a kit that includes 5 tips, a desoldering pump and anti-static tweezers.
Pros
- Auto-feed system delivers wire to the tip for one-handed soldering
- LCD display shows the operating temperature in real time
- Heats up in 15 seconds from a 60W ceramic heater
- 180-500°C range covers delicate electronics and heavier wires
Cons
- No warranty term is stated
- Auto-feed suits 0.8-1.0 mm solder wire, with 1.0 mm recommended
- Designed for a standard US 110V power supply
- Tip shapes are not named, so the 5 tips may not include a fine tip for small pads

ANBES Soldering Iron Kit Electronics,60W
A 60W iron kit with 5 tips, a 200-450°C range, a desoldering pump and a 14-in-1 set for PCB assembly and repair.
Pros
- 200-450°C adjustable range for PCB assembly and home appliance repair
- 5 interchangeable tips with a heat-resistant screw thread that holds the tip in place
- Desoldering pump removes solder from PCB through-hole joints
- 14-in-1 kit adds tweezers, a wire stripper cutter and a storage bag
Cons
- No warranty term is stated
- Heat-up time is not stated
- No temperature display is stated
- 14 pieces need storage space between jobs

Soldering Iron Kit, 80W 110V LCD Digital Solder
An 80W LCD soldering iron kit with a ceramic heater, heat-up in 20 seconds, 5 tips, a stand, solder wire, sponge and paste.
Pros
- 80W with heat-up within 20 seconds
- LCD display with temperature from 180 to 480°C
- 5 tips with a stand, solder wire, sponge and paste
- 4 ventilation holes for heat dissipation and an anti-scalding handle
Cons
- No warranty term is stated
- No auto sleep or temperature memory is stated
- No on/off switch is stated
- No cordless mode is stated; the iron runs on 110V

Weller W100PG Weller Farenheit Heavy Duty
A 100W heavy-duty iron with a CT6F7 tip, rated at 700 degrees, for larger solder joints.
Pros
- 100W output for heavy-duty joints
- Rated at 700 degrees with the CT6F7 tip
- Weighs 0.6 pounds, so the iron stays light in the hand
- 120V supply matches standard US benches
Cons
- Iron only, with no stand, pump or spare tips in the box
- No adjustable temperature is stated
- 100W suits larger joints better than small pads
- Measures 5.0 x 2.0 x 11.75 inches, so the iron is long for tight bench spaces

Soldering Iron Kit, 60W Soldering Iron with 5pc
A portable 60W soldering iron kit: 5 tips, 0.6mm solder wire, flux paste.
Pros
- 60W iron, 392°F to 842°F, or 200-450°C
- Heats to the desired temperature within 15 secs
- 5 tips, 0.6mm wire, flux paste
- Portable: plug in and use, ON/OFF switch
Cons
- No warranty term stated in the listing
- No safety certification stated in the listing
- No digital display stated for the iron
- Included stand described as a simple stand
Specs compared
| Model | HQ Score | Power | Temperature | Tips | Kit | Stand | Warranty |
|---|---|---|---|---|---|---|---|
| EOOKU 60W Auto Feed | 9.6/10 | 60W | 180-500°C | 5 tips | Pump, tweezers, cleaner | Built-in stand | Not stated |
| ANBES 60W Kit | 9.6/10 | 60W | 200-450°C | 5 tips | 14-in-1 kit | Dual-spring holder | Not stated |
| Weller W100PG 100W | 9.4/10 | 100W | 700 degrees | CT6F7 tip | Iron only | Not stated | Not stated |
| Q-MING 80W LCD | 9.5/10 | 80W | Not stated | 5 tips | Stand, wire, sponge, paste | Stand | Not stated |
| Q-MING 60W Kit | 9.4/10 | 60W | Not stated | 5 tips | 10-in-1 kit | Not stated | Not stated |
Size and performance figures are the brand’s ratings quoted from listings on 21 November 2026.
Best Soldering Iron for Pcb Work: What Matters on a Board
Power sets how fast an iron recovers heat after each joint. The irons here are rated at 60W, 80W and 100W, and the 100W Weller suits larger joints while the 60W kits suit fine board work. Temperature range matters just as much: the EOOKU covers 180-500°C and the ANBES covers 200-450°C, so both can run cool enough for delicate parts and hot enough for heavier wires. The EOOKU shows its temperature on an LCD, and the Q-MING 80W iron also carries an LCD display.
Tips decide whether the iron fits the pad. The kits here include 5 tips each, and the ANBES and EOOKU kits add a desoldering pump for through-hole rework, tweezers for holding parts, and a stand for resting the iron. A stand keeps a hot tip away from wires, boards and fingers while the next part is placed.
Buying guide: soldering irons for PCB work
Match the iron to the joint
Fine pads and small parts suit a 60W iron with a fine tip, while larger joints suit more power. The Weller is the only 100W iron here, and it carries a CT6F7 tip rated at 700 degrees, so it suits heavier joints rather than the smallest pads. The 60W kits suit general board work.
Temperature range and heat-up
A wide range covers more work. The EOOKU runs from 180-500°C and heats up in 15 seconds, so it is ready quickly and can drop low for delicate parts. The ANBES runs from 200-450°C. The two Q-MING irons state adjustable temperature without a range, and the Weller runs at its rated 700 degrees.
Tips, stands and cleanup
Five tips come with the EOOKU, the ANBES and both Q-MING kits, while the Weller comes with its CT6F7 tip. A desoldering pump comes with the EOOKU and ANBES kits and clears solder from through-hole joints, which matters when a part must come off a board. The EOOKU has a built-in stand, the ANBES has a dual-spring holder with a sponge, and the Q-MING 80W kit includes a stand, so each bench setup keeps the hot iron off the work surface.
Solder wire and desoldering
The EOOKU is designed for 0.8-1.0 mm solder wire, with 1.0 mm recommended, and the maker suggests 60/40 or 63/37 rosin core solder. That guidance suits the auto-feed system, which delivers wire to the tip. For rework, the desoldering pump in the EOOKU and ANBES kits removes old solder with suction, so a misplaced joint can be cleared and redone without a separate tool.
Soldering makes fumes and hot surfaces, so work with ventilation, eye protection and a heat-proof surface under the board. Wash hands after handling solder, and keep lead solder away from food-contact items. Rest the iron in its stand whenever it is not in hand.
Project Match
Each pick suits a different bench job, based on what its listing states:
- PCB assembly and repair: the EOOKU and ANBES kits, which both state PCB work and include a desoldering pump
- Through-hole rework: the ANBES and EOOKU kits, with a pump for clearing through-hole joints
- Phone and computer repair: the ANBES kit, which names phone and computer repairs among its uses
- Stained glass and jewelry making: the ANBES kit, which names both uses
- Larger joints: the Weller 100W iron with its CT6F7 tip
How the scores add up
Each iron is scored out of 10 on performance, build, value, safety and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| EOOKU 60W Auto Feed | 9.6 | 32 | 21 | 21 | 5 | 0 |
| ANBES 60W Kit | 9.6 | 29 | 21 | 21 | 5 | 0 |
| Weller W100PG 100W | 9.4 | 28 | 21 | 16 | 0 | 0 |
We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.
FAQ: lasers and CNC
What wattage is right for PCB work?
The picks here are rated at 60W, 80W and 100W. A 60W iron suits general board work, an 80W iron suits heavier joints, and the 100W Weller suits the largest joints here. Wattage alone does not set quality: temperature range, tips and the kit around the iron matter as much.
What temperature range should a PCB iron cover?
The EOOKU covers 180-500°C and the ANBES covers 200-450°C, which covers delicate parts at the low end and heavier wires at the high end. The Q-MING irons state adjustable temperature without a range, and the Weller is rated at 700 degrees with its CT6F7 tip.
How many tips do I need for PCB work?
The EOOKU, ANBES and Q-MING kits each include 5 tips, and the Weller includes its CT6F7 tip. Tip shapes are not named here, so a buyer who needs a specific fine tip should confirm the shapes before ordering.
Do I need a desoldering pump for PCB rework?
A pump helps when a part must come off a board. The EOOKU and ANBES kits include a desoldering pump for clearing solder from through-hole joints, while the Weller and the Q-MING kits do not include one.
Which of these irons have a stated warranty?
None of the five irons here state a warranty term. That is why warranty scores are zero across the picks, and buyers who want written cover should ask the maker before ordering.
Related: best soldering station for hobbyists, best soldering mat, best flux for soldering jewelry, best solder for aluminum and the electronics making hub. Also see the best small multimeter.




