What Wood Is Best for Burning: Basswood Blanks for Pyrography and Laser Engraving
Basswood takes the cleanest burn for pyrography and laser engraving, and the right blank depends on size, thickness and the project in hand.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
36 Pack Basswood Sheets 1/8 inch,12"x12"x1/8"9.6/10View on Amazon - 2
kukmakri 120 PCS Unfinished Plywood Sheets9.5/10View on Amazon - 3
16 Pack Basswood Sheets 1/4 inch,12x12x1/4Iinch9.5/10View on Amazon - 4
24Pcs 16 x 12 x 1/8 Inch Basswood Sheets9.4/10View on Amazon
A blank that burns clean makes the difference between a design that reads clearly and a design that fights the burner. The wood decides how dark the burn goes and how smooth the lines stay. For most makers, the answer to what wood is best for burning is basswood: pale, fine-grained and soft, and sold as ready blanks for pyrography and laser work.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

36 Pack Basswood Sheets 1/8 inch,12"x12"x1/8"
36 unfinished basswood sheets, 12 x 12 in and 1/8 in thick, made for laser cutting, engraving and wood burning.
Pros
- 36 sheets covers a run of signs, coasters and practice pieces
- 12 x 12 in sheets (305 x 305 mm) fit signs, wall decor and name puzzles
- Smooth, flat surface with edges that need no re-sanding
- Manufacturer warranty for 90 days from date of purchase
Cons
- 1/8 in thickness is thin for deep relief work
- 12 x 12 in sheets limit single-piece design size
- Unfinished surface needs a finish before outdoor display
- 36 sheets is more than a casual burner needs

kukmakri 120 PCS Unfinished Plywood Sheets
120 unfinished plywood squares, 6 x 6 in and 0.1 in thick, for wood burning, laser engraving, coasters and home decor.
Pros
- 120 pieces, the largest count here, for practice and coasters
- 6 x 6 in squares suit coasters, wall art and small signs
- Smooth, clean surface ready for paint, stain or laser engraving
- 0.1 in thickness keeps squares light for hanging pieces
Cons
- 6 x 6 in size is too small for large signs
- 0.1 in thickness is the thinnest stock here
- No warranty term is stated
- 120 pieces is more than a single-project buyer needs

16 Pack Basswood Sheets 1/4 inch,12x12x1/4Iinch
16 unfinished basswood sheets, 12 x 12 in and 1/4 in thick, for laser cutting, engraving and wood burning.
Pros
- 1/4 in (6.0 mm) thickness is the thickest stock here
- 12 x 12 in sheets (305 x 305 mm) suit home decor and door signs
- Flat, smooth surface without warping, with neat edges
- 16 sheets is a practical count for matching pieces
Cons
- No warranty term is stated
- 8.0 pounds is heavy for a pack of 16 sheets
- 16 sheets is the smallest pack count here
- 1/4 in thickness suits sturdy pieces, not fine work

24Pcs 16 x 12 x 1/8 Inch Basswood Sheets
24 unfinished basswood sheets, 16 x 12 in and 1/8 in thick, for laser cutting, crafts, painting, wood engraving and pyrography.
Pros
- 16 x 12 in sheets are the largest blanks here
- 24 sheets covers a run of projects
- Beautiful, even grain with no burrs and no warping
- 1/8 in (3 mm) thickness cuts easily on a laser or scroll saw
Cons
- 16 x 12 in sheets need a work area that fits the sheet
- 1/8 in thickness is thin for deep relief work
- Unfinished surface needs a finish before outdoor display
- 24 sheets is more than a single-project buyer needs
What Wood Is Best for Burning
Basswood leads because its grain stays even and its surface stays pale, so burn lines show with steady contrast. The blanks in this guide are unfinished basswood and unfinished plywood, listed for wood burning and laser engraving.
Grain matters more than species name alone. Even grain burns at a steady pace, while wild grain can darken in patches. The ACXFOND sheets (on Amazon) list beautiful, even grain, and the Ninekong sheets (on Amazon) list a smooth surface with edges that need no re-sanding.
Thickness sets what the blank can become. Thin stock suits coasters and wall art, while thick stock suits signs and boxes. The blanks here run from 0.1 in to 1/4 in thick.
How to Pick a Burning Blank
Start with size. A 12 x 12 in sheet suits signs, wall decor and name puzzles, while a 6 x 6 in square suits coasters and small wall art. The largest blanks here measure 16 x 12 in, which suits wide designs and model work.
Then match thickness to the job. Sheets at 1/8 in (3.0 mm) cut and engrave with ease on a laser, and 1/4 in (6.0 mm) sheets give sturdier stock for boxes and signs. Squares at 0.1 in stay light for hanging pieces.
Check the pack count. A pack of 36 sheets covers a run of matching pieces, a pack of 120 squares covers practice and batches of coasters, and a pack of 16 sheets covers a set of signs. Unfinished blanks take the finish of your choice.
Burn Safely: Ventilation and Fire
Wood burning makes smoke, so work where air moves and fumes leave the room. Keep the bench clear while the burner is hot, and let the tool cool on a heat-proof rest before putting it away. Never leave a hot burner or a running laser unattended.
Laser work adds its own rules. Never laser PVC, vinyl, PVC faux leather, polycarbonate or ABS, and check the materials you should never laser cut guide before cutting a new material. Keep a suitable extinguisher within reach.
Basswood Blanks for Wood Burning
The blanks below cover the sizes and thicknesses this guide recommends.
FAQ: lasers and CNC
Is basswood the best wood for wood burning?
For most makers, yes. Basswood has a pale surface and even grain, so burn lines show with steady contrast. Blanks come in sizes from 6 x 6 in squares to 16 x 12 in sheets, and the blanks here are all basswood or unfinished plywood listed for wood burning.
What thickness works best for wood burning?
It depends on the piece. Sheets at 1/8 in suit flat work and fine lines, while 1/4 in sheets suit sturdy signs and boxes. Squares at 0.1 in suit coasters and ornaments.
Is plywood good for wood burning?
Yes, unfinished plywood works for small pieces. The kukmakri squares (on Amazon) here are unfinished plywood, 6 x 6 in and 0.1 in thick, listed for wood burning, laser engraving and coasters. Keep to unfinished stock and ventilate while burning.
What size blank is best to start with?
A 12 x 12 in sheet suits signs and wall decor, and a 6 x 6 in square suits coasters and motifs. The choice comes down to the design rather than the wood.
Does basswood need sanding before burning?
Usually not much. The Ninekong sheets list a smooth surface with edges that need no re-sanding, and the ACXFOND sheets list polished sheets with no burrs and no warping. A light pass is enough if the blank feels rough to the touch.
Related: the best wood burning kit guide, best basswood for laser engraving and basswood vs cherry for laser engraving.




