Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

V Block Types for Machining and Workholding

V block types for machining and workholding range from clamped hardened steel sets to a cast iron matched pair, and the right choice depends on round stock size, stated accuracy and whether clamps are included.

V Block Types for Machining and Workholding
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1TEXALAN(R) 3 X 1-3/4 X 2-3/8Inch Cast Iron V BlockTEXALAN(R) 3 X 1-3/4 X 2-3/8Inch Cast Iron V Block9.5/10View on Amazon
  2. 2HFS(R) V Blocks with Clamp Set 1-3/8 x 1-3/8 xHFS(R) V Blocks with Clamp Set 1-3/8 x 1-3/8 x9.5/10View on Amazon
  3. 3findmall 2-3/8 x 2-3/8 x 2 V Block with Clamp Setfindmall 2-3/8 x 2-3/8 x 2 V Block with Clamp Set9.5/10View on Amazon
  4. 4VME VB-1 V Block and Clamp Set 1 Inch CapacityVME VB-1 V Block and Clamp Set 1 Inch Capacity9.4/10View on Amazon

V block types answer a plain shop question: how to hold round stock steady while it is drilled, milled, ground or measured. A V block is a machined block with a V-shaped groove that cradles a shaft, pipe or other round part, so the part stays in line instead of rolling on a flat surface. This guide explains the main v block types and which stated size, material and accuracy figures matter when choosing a V block for machining and workholding.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

TEXALAN(R) 3 X 1-3/4 X 2-3/8Inch Cast Iron V Block

TEXALAN(R) 3 X 1-3/4 X 2-3/8Inch Cast Iron V Block

TEXALAN9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A cast iron matched pair machined square and parallel, with stated accuracy up to 0.0001 in and a size of 3 x 1-3/4 x 2-3/8 in for large jobs.

Pros

  • Accuracy up to 0.0001 in, the finest stated accuracy here
  • Cast iron machined square and parallel
  • V width of 1-3/4 in and depth of 2-3/8 in
  • Matched pair for straightness and alignment

Cons

  • No clamp is listed with the pair
  • Hardness is not stated
  • No carrying case is listed with the pair
  • At 3 in long, the pair takes more bench space
HFS(R) V Blocks with Clamp Set 1-3/8 x 1-3/8 x

HFS(R) V Blocks with Clamp Set 1-3/8 x 1-3/8 x

HFS9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A hardened steel 90 degree V block set with clamps, sized 1-3/8 x 1-3/8 x 1-3/16 in and rated for a holding range of 3/25 to 19/32 in.

Pros

  • Hardened steel with hardness of HRC 58 to 60
  • Squareness and parallelism accuracy of 0.0002 in
  • Clamps included for stable holding during machining
  • Holding range of 3/25 to 19/32 in covers pipes and workpieces

Cons

  • At 1-3/8 x 1-3/8 x 1-3/16 in, the set suits small work only
  • Holding range tops out at 19/32 in
  • Minimum holding range of 3/25 in leaves smaller stock uncovered
  • No carrying case is listed with the set
findmall 2-3/8 x 2-3/8 x 2 V Block with Clamp Set

findmall 2-3/8 x 2-3/8 x 2 V Block with Clamp Set

findmall9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A hardened steel 90 degree V block pair with clamps and a wooden case, sized 2-3/8 x 2-3/8 x 2 in with a clamping range of 8-30 mm.

Pros

  • Hardened steel with hardness of HRC 58 to 60
  • Square and parallel to an accuracy of 0.0002
  • Wooden case included for carrying and storage
  • Clamping range of 8-30 mm and max capacity of 1-3/16 in

Cons

  • Max capacity of 1-3/16 in limits larger round stock
  • At 2-3/8 x 2-3/8 x 2 in, the blocks take more bench space
  • Clamping range of 8-30 mm needs care with inch-size stock
  • The wooden case adds bulk when the set is carried
VME VB-1 V Block and Clamp Set 1 Inch Capacity

VME VB-1 V Block and Clamp Set 1 Inch Capacity

Vee Blocks9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A hardened steel V block and clamp set with a 1 inch capacity and a 1-5/8 inch width for milling, drilling, inspection and metalworking.

Pros

  • Holds round workpieces up to 1 inch diameter with clamps
  • Pair of 2 V blocks and 2 clamps for parallel alignment
  • Hardened steel construction, described by the maker as wear resistant
  • Suits CNC machines, drill presses, surface plates and toolroom inspections

Cons

  • No accuracy figure is stated
  • Capacity tops out at 1 inch diameter
  • No hardness figure is stated
  • No carrying case is listed with the set

V Block Types Explained

The v block types in this guide fall into clamped sets and a matched pair that holds large jobs without clamping. Clamped sets use a clamp over the round stock to keep it seated during drilling, milling and grinding, while the matched pair is listed for holding large jobs without clamping. Hardened steel blocks resist wear, and the cast iron pair is machined square and parallel.

How to Choose V Block Types

Choosing v block types starts with the round stock and the job. Match capacity to the stock, check the stated accuracy, and confirm what arrives in the box.

  • Capacity: from 1 inch for the VME set to a max capacity of 1-3/16 in for the findmall set, with the HFS set covering a holding range of 3/25 to 19/32 in.
  • Accuracy: 0.0002 in for the HFS and findmall sets and up to 0.0001 in for the TEXALAN pair.
  • Material: hardened steel at HRC 58 to 60 for the HFS and findmall sets, and cast iron for the TEXALAN pair.
  • Included parts: clamps arrive with the HFS, findmall and VME sets, a wooden case arrives with the findmall set, and no clamp is listed with the TEXALAN pair. See the types of toggle clamps for workholding for other holding options.

V Blocks for Machining and Workholding

The V blocks below cover the holding step in the answer above: each one seats round stock in a V groove for machining and inspection, and the choice turns on capacity, stated accuracy and whether clamps are included.

FAQ: lasers and CNC

What is a V block used for?

A V block holds round stock, shafts and cylindrical parts steady for machining, milling, drilling, grinding and inspection. The V groove cradles the part so it stays in line on a surface plate or machine table instead of rolling.

What accuracy do V blocks offer?

The HFS and findmall sets list squareness and parallelism accuracy of 0.0002 in, and the TEXALAN pair lists accuracy up to 0.0001 in. The VME set states no accuracy figure.

How to choose a V block size for round stock?

The VME set holds round workpieces up to 1 inch in diameter, the findmall set lists a max capacity of 1-3/16 in with a clamping range of 8-30 mm, and the HFS set lists a holding range of 3/25 to 19/32 in.

What comes with a V block set?

It varies by listing. The findmall package includes 2 V blocks, 2 clamps and 1 wooden case, the VME set includes 2 V blocks and 2 clamps, and the TEXALAN pair is supplied as a matched pair with no clamp listed.

Related: the CNC tooling hub, V block vs angle plate, best V blocks for machinists and best large V blocks.

More buying guides

CNC Tooling ·

Best Large V Blocks (2026)

Cast iron and magnetic v blocks for large jobs, compared by size, accuracy, V width, weight and type, with the stated specs and who…