Best Large V Blocks (2026)
Cast iron and magnetic v blocks for large jobs, compared by size, accuracy, V width, weight and type, with the stated specs and who should skip each.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallTEXALAN 6 in V Block9.5/10View on Amazon - 2
Best Large SetHFS 5 in V Block Set9.5/10View on Amazon - 3
Best for CalibrationOtoolling Mag V Block9.4/10View on Amazon - 4
Best Matched SetHHIP 3 in V Block Set9.4/10View on Amazon
A round bar that has to stay put while it is drilled, milled or checked needs a block that holds it square, and a large v block gives that hold without a clamp in the way.
This guide covers the best large v blocks, with 5 cast iron and magnetic blocks compared by size, accuracy, V width, weight and type, and the stated specs for each.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall TEXALAN 6 in V Block: Highest HQ Score here: 6 in cast iron set, 0.0001 in accuracy, 3-1/8 in V width and a 12.0 lb weight stated Check price on Amazon
- Best Large Set HFS 5 in V Block Set: Matched 2-block set, 5 x 2-1/2 x 3-1/8 in, 0.0001 in accuracy, cast iron Check price on Amazon
- Best for Calibration Otoolling Mag V Block: Magnetic 3-sided block with an on/off switch, 2.875 in high, for calibration and measurement Check price on Amazon
- Best Matched Set HHIP 3 in V Block Set: Matched set, 3 x 1-3/4 x 2-3/8 in, 0.0005 in tolerance, seasoned cast iron Check price on Amazon
Machines on the list

TEXALAN(R) 6 X 3-1/2 X2-1/2Inch Cast Iron V Block
Cast iron v block set, 6 x 3-1/2 x 2-1/2 in, machined square and parallel, with 0.0001 in accuracy and a 3-1/8 in V width.
Pros
- Largest size here at 6 in, with a 3-1/8 in V width
- 0.0001 in accuracy stated
- Matched set for holding large jobs without clamping
- Weight stated at 12.0 lb
Cons
- No warranty term is stated
- Heaviest here at 12.0 lb
- No magnetic hold is stated
- No V depth is stated

HFS(R) Cast Iron V-Block Set
Matched cast iron v block set, 5 x 2-1/2 x 3-1/8 in, precision ground, with 0.0001 in accuracy for machining, inspection and setup.
Pros
- 0.0001 in accuracy stated
- Matched set for consistent alignment on longer workpieces
- Cast iron for rigidity and stability
- Precision ground for machining, inspection and setup
Cons
- No V width is stated
- No weight is stated
- No warranty term is stated

HHIP 3 X 1-3/4 X 2-3/8 INCH CAST Iron V Block Set
Matched cast iron v block set, 3 x 1-3/4 x 2-3/8 in, machined square and parallel, with a 0.0005 in tolerance and a 1-3/4 in V width.
Pros
- Matched set for uniformity in workholding setups
- Seasoned cast iron to prevent distortion
- V width and depth stated: 1-3/4 in and 1-5/16 in
- 0.0005 in tolerance stated for critical setup tasks
Cons
- Accuracy is 0.0005 in, looser than the 0.0001 in on the TEXALAN and HFS
- No weight is stated
- No warranty term is stated

Otoolling Magnetic V Block with Switch 2.875" High
Magnetic v block with an on/off switch, 2.875 in high by 2.36 in wide by 3.5 in deep, with 3-sided magnetic force for calibration and measurement.
Pros
- 3-sided magnetic hold with an on/off switch
- Hardened precision ground faces to resist wear
- Suits calibration, measurement and inspection
- Compact size for bench and on-site use
Cons
- No accuracy figure is stated
- No weight is stated
- No warranty term is stated

Groz 03100 Cast Iron V Block with 3-Inch Base
Cast iron v block with a 3 in base length, precision ground and machined, for holding large jobs at 90 degrees during drilling, milling and grinding.
Pros
- Holds large jobs at a 90-degree angle without clamping
- Precision ground and machined square and parallel
- Cast iron for rugged durability
- 2 pack for holding longer workpieces
Cons
- No accuracy figure is stated
- No weight is stated
- No V width or depth is stated
- No warranty term is stated
Specs compared
| Model | HQ Score | Size | Accuracy | V width | Weight | Type | Warranty |
|---|---|---|---|---|---|---|---|
| TEXALAN 6 in V Block | 9.5/10 | 6 x 3-1/2 x 2-1/2 in | 0.0001 in | 3-1/8 in | 12.0 lb | Matched set | Not stated |
| HFS 5 in V Block Set | 9.5/10 | 5 x 2-1/2 x 3-1/8 in | 0.0001 in | Not stated | Not stated | Matched set | Not stated |
| HHIP 3 in V Block Set | 9.4/10 | 3 x 1-3/4 x 2-3/8 in | 0.0005 in | 1-3/4 in | Not stated | Matched set | Not stated |
| Otoolling Mag V Block | 9.4/10 | 2.875 x 2.36 x 3.5 in | Not stated | Not stated | Not stated | Magnetic, 3-sided | Not stated |
| Groz 03100 V Block | 9.4/10 | 3 in base | Not stated | Not stated | Not stated | 2 pack | Not stated |
Size and performance figures are the brand’s ratings quoted from listings on 11 November 2026.
What the listings tell you, and what they leave out
All 5 picks are cast iron except the magnetic Otoolling block. The TEXALAN and HFS listings state 0.0001 in accuracy, the HHIP states 0.0005 in, and the Groz and Otoolling listings state no accuracy figure. Only the TEXALAN listing states a weight, 12.0 lb. The HFS, HHIP and Otoolling listings disagree with their own spec tables on dimensions, so the reviews use the title and bullets.
Buying guide: the best large v blocks
Size and V width
Sizes run 3 in on the Groz base to 6 in on the TEXALAN, with the HFS at 5 in, the HHIP at 3 in and the Otoolling at 2.875 in high. V width is stated on the TEXALAN, 3-1/8 in, and the HHIP, 1-3/4 in. A wider V suits larger round stock; see the best v blocks for machinists.
Accuracy
The TEXALAN and HFS listings state 0.0001 in accuracy, and the HHIP states 0.0005 in. The Groz and Otoolling listings state no accuracy figure. For inspection work, a stated accuracy matters more than size; for rough holding, any of these blocks holds the stock square.
Matched sets and magnetic hold
The TEXALAN, HFS and HHIP listings sell matched sets, which keep longer workpieces aligned across 2 blocks. The Groz comes as a 2 pack. The Otoolling is a magnetic block with an on/off switch and 3-sided magnetic force, which suits calibration and measurement where a clamp would get in the way.
Cast iron and hardening
Cast iron gives the rigidity and stability these blocks need. The HHIP listing says its cast iron is seasoned to prevent distortion. The Otoolling listing says its contact faces are hardened to resist wear. None of the listings states a warranty term.
Holding large jobs without clamping
The TEXALAN and Groz listings say the blocks hold large jobs where clamping is not necessary. The TEXALAN is the largest here at 6 in, with a 3-1/2 in depth and a 12.0 lb weight stated. The Groz holds large jobs at a 90-degree angle for drilling, milling and grinding.
Project Match
- Machining and inspection of round stock: the TEXALAN and HFS sets, with 0.0001 in accuracy stated and matched blocks for longer workpieces.
- Holding large jobs without clamping: the TEXALAN at 6 in and the Groz with a 3 in base, each listed for large jobs.
- Calibration and measurement: the Otoolling magnetic block, with an on/off switch and 3-sided magnetic force.
- Layout and setup on smaller stock: the HHIP set, 3 x 1-3/4 x 2-3/8 in with a 1-3/4 in V width.
- Drilling, milling and grinding at 90 degrees: the Groz block, listed for holding large jobs at a 90-degree angle.
How the scores add up
The HQ Score weighs performance (size, accuracy, V width and holding type), build quality (cast iron, machining and hardening), value (what the set includes for the size) and warranty (years and coverage). No listing states a safety feature or a certification, so safety earns no points on any pick. A factor the listing does not state scores no points.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| TEXALAN 6 in V Block | 9.5 | 32 | 22 | 21 | 0 | 0 |
| HFS 5 in V Block Set | 9.5 | 30 | 21 | 21 | 0 | 0 |
| HHIP 3 in V Block Set | 9.4 | 28 | 21 | 20 | 0 | 0 |
| Otoolling Mag V Block | 9.4 | 28 | 21 | 19 | 0 | 0 |
| Groz 03100 V Block | 9.4 | 27 | 20 | 20 | 0 | 0 |
We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.
FAQ: lasers and CNC
What is a v block used for?
A v block holds round or cylindrical workpieces for machining, inspection, layout and setup. The V shape centers the stock, and a matched set holds longer workpieces aligned across 2 blocks.
What accuracy do I need in a v block?
It depends on the job. The TEXALAN and HFS listings state 0.0001 in accuracy, and the HHIP states 0.0005 in. For inspection work, a stated accuracy matters; for rough holding, any of these blocks holds the stock square.
Do v blocks come in matched sets?
Some do. The TEXALAN, HFS and HHIP listings sell matched sets, and the Groz comes as a 2 pack. A matched set keeps longer workpieces aligned across 2 blocks.
What is a magnetic v block?
A magnetic v block holds workpieces with magnetic force instead of a clamp. The Otoolling block has an on/off switch and magnetic force across its upper, lower and V-channel surfaces, and the listing names calibration, measurement and inspection as uses.
Can a v block hold large jobs without clamping?
Yes, per the listings. The TEXALAN and Groz listings say the blocks hold large jobs where clamping is not necessary. The TEXALAN is the largest here at 6 in.
Related: the best v blocks for machinists, our cnc tooling hub, our aluminum cutting fluid guide and our aluminum t-track hold-down clamps guide.




