Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Pillow Block Bearing Assembly: CNC Mounting Guide

A pillow block bearing assembly holds a rotating shaft in a cast iron housing, and this guide matches bore, mount style and pack size to a CNC build.

Pillow Block Bearing Assembly: CNC Mounting Guide
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 12 Pack UCP205-16 Pillow Block Mounted Ball Bearing2 Pack UCP205-16 Pillow Block Mounted Ball Bearing9.6/10View on Amazon
  2. 22 Pack UCFL204-12 Pillow Block Bearing2 Pack UCFL204-12 Pillow Block Bearing9.6/10View on Amazon
  3. 3PGN Pillow Block Bearing for 1 Inch ShaftPGN Pillow Block Bearing for 1 Inch Shaft9.6/10View on Amazon
  4. 4Gisafai 8 Pcs UCP205-16 Pillow Block BearingGisafai 8 Pcs UCP205-16 Pillow Block Bearing9.6/10View on Amazon

A CNC router that chatters on every pass, a shaft that wobbles in its mount, a frame that never holds square: the cause often sits where the shaft meets the frame, and a pillow block bearing assembly is the part that holds the shaft steady while it spins. This guide explains what the assembly is, how the mount styles differ, and how to match bore, housing and pack size to a CNC build, using the listings below as the source for every figure.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

2 Pack UCP205-16 Pillow Block Mounted Ball Bearing

2 Pack UCP205-16 Pillow Block Mounted Ball Bearing

SACKORANGE9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 pack UCP205-16 pillow block bearing with a 1-inch bore, a solid cast iron base and a self-aligning insert for 1-inch shafts.

Pros

  • 1-inch bore matches 1-inch shafts, per the listing
  • Solid cast iron base gives the mount a sturdy footing
  • Self-aligning insert adjusts to misalignment
  • 2 pack supplies matching units for a shaft with a mount at each end

Cons

  • No warranty term is stated
  • 1-inch bore only: a 3/4-inch shaft needs a different unit
  • No seal type is stated in the listing
  • Item weight of 1.3 pounds
2 Pack UCFL204-12 Pillow Block Bearing

2 Pack UCFL204-12 Pillow Block Bearing

SACKORANGE9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 pack UCFL204-12 flange mount bearing with a 3/4-inch bore, a 2-bolt flange and a double layer seal for 3/4-inch shafts.

Pros

  • 3/4-inch bore for 3/4-inch shafts
  • 2-bolt flange mounts to a flat face
  • Double layer seal keeps impurities and water out, per the listing
  • Bearing steel insert in a self-aligning cast iron housing

Cons

  • No warranty term is stated
  • 3/4-inch bore only: a 1-inch shaft needs a different unit
  • Set screw locking style needs the set screw seated on the shaft
  • Item weight of 1.0 pounds
PGN Pillow Block Bearing for 1 Inch Shaft

PGN Pillow Block Bearing for 1 Inch Shaft

PGN Bearings9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A PGN UCP205-16 pillow block bearing with a 1-inch bore, an AISI 52100 chrome steel body and a solid cast iron housing.

Pros

  • AISI 52100 chrome steel body built for wear resistance
  • 1-inch bore for 1-inch shafts
  • Solid cast iron housing holds the bearing in position
  • Self-aligning configuration adjusts to misalignment

Cons

  • No warranty term is stated
  • No seal or dust cover is stated
  • The 2.8 x 5.5 x 2.8-inch housing needs its 5.5-inch side planned into the frame
Gisafai 8 Pcs UCP205-16 Pillow Block Bearing

Gisafai 8 Pcs UCP205-16 Pillow Block Bearing

Gisafai9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-piece set of UCP205-16 pillow block bearings with a 1-inch bore, a green cast iron housing and a double layer dust cover.

Pros

  • 8 pieces cover multiple installs or spares
  • 1-inch bore for 1-inch shafts
  • Double layer dust cover keeps dust and dirt out, per the listing
  • Green housing is easy to spot during install or maintenance

Cons

  • Title calls these 2-bolt flange bearings, but UCP205-16 is a pillow block unit
  • No warranty term is stated
  • Size is listed as approximately 5.51 inches / 140 mm, so the figure is approximate
  • Bullet size of 5.51 inches and spec dimensions of 9.45 x 6.3 x 3.15 inches do not match

Pillow Block Bearing Assembly: What It Is

A pillow block bearing assembly is a mounted ball bearing unit: a bearing insert seated in a cast iron housing with bolt holes, ready to fix to a frame. The inner ring turns with the shaft, the housing stays put, and the self-aligning insert adjusts to misalignment between mounts, which is the feature every listing here states. The housings in this guide are cast iron, the inserts are bearing steel, and the PGN unit names its steel as AISI 52100 chrome steel.

How to Match a Pillow Block Bearing Assembly to a Shaft

Start with the bore. A 1-inch bore fits a 1-inch shaft, and the listings here state that match in plain words for the UCP205-16 units, while the UCFL204-12 flange unit states a 3/4-inch bore for a 3/4-inch shaft. A bore that is larger than the shaft leaves play; a bore that is smaller never fits. Match the number on the listing to the shaft in the build, not to a nearby size.

Then pick the mount style. A pillow block base bolts down to a flat surface under the shaft, while a 2-bolt flange bolts to a face and suits a mount where the shaft passes through a panel. The flange unit here is the UCFL204-12; the other units are UCP205-16 pillow blocks. Check the housing dimensions against the frame space: the SACKORANGE pillow block lists 3.0 x 2.0 x 3.0 inches, the PGN lists 2.8 x 5.5 x 2.8 inches, and the flange unit lists 3.0 x 2.0 x 4.0 inches.

Then count the pack. The SACKORANGE and PGN listings are 2 pack units, and the Gisafai listing is an 8-piece set, so a build with a mount at each end of a shaft takes one pack of 2, while a larger build or a spares drawer takes the 8-piece set. Read the pack count in the title and bullets: the PGN spec table lists 1 item where the title and bullets say 2 pack, and the title and bullets are the figures to trust.

Pillow Block Bearing Assembly Picks for a CNC Build

The assemblies below cover the bore sizes and mount styles in this guide, and each card names the part of the build it handles.

Mounting Checks That Keep a Shaft True

Mounting is where a good assembly earns its keep. Work through these checks with the housing in hand:

  • Seat the shaft fully: the bore must match the shaft, and the shaft must pass through the bore before the housing bolts are tightened down.
  • Use the self-aligning insert: let the insert settle to the shaft line rather than forcing the housing to a crooked mount.
  • Mind the seal: the flange unit states a double layer seal that keeps impurities and water out, and the Gisafai set states a double layer dust cover; the two pillow block units state no seal, so no dust protection is stated for them.
  • Lock it down: the flange unit uses a set screw locking style, so seat the set screw on the shaft as the listing states.

FAQ: lasers and CNC

What is a pillow block bearing assembly?

A mounted ball bearing unit: a bearing insert seated in a cast iron housing with bolt holes, fixed to a frame so it supports a rotating shaft. The inner ring turns with the shaft while the housing stays put, and the self-aligning insert adjusts to misalignment between mounts.

What bore size do I need for a pillow block bearing assembly?

Match the bore to the shaft: a 1-inch bore for a 1-inch shaft, as the UCP205-16 listings state, or a 3/4-inch bore for a 3/4-inch shaft, as the UCFL204-12 listing states. Measure the shaft, then match the number on the listing to it.

What is the difference between a pillow block and a flange bearing?

A pillow block base bolts down under the shaft, while a 2-bolt flange bolts to a face. The UCP205-16 units here are pillow blocks; the UCFL204-12 is the flange unit, with a set screw locking style.

How many bearings come in a pack?

The SACKORANGE and PGN listings are 2 pack units, and the Gisafai listing is an 8-piece set. Check the title and bullets for the count: the PGN spec table lists 1 item where the title and bullets say 2 pack.

Are pillow block bearing assemblies self-aligning?

All 4 listings here state a self-aligning insert that adjusts to misalignment. That helps when mounts on a frame are not perfectly in line, but it does not replace fitting the shaft straight through the bore.

What materials are these housings made from?

Cast iron housings and bearing steel inserts, per the listings. The PGN unit names its steel as AISI 52100 chrome steel, and the Gisafai housings (on Amazon) are green cast iron.

Related: the CNC routers hub, shaft coupler types for CNC builds and linear bearing guide rails. Also see our stepper motor size guide.

More buying guides

CNC Routers ·

CNC Milling Machine Setup for Beginners

A beginner guide to CNC milling machine setup: square the vise, indicate the fixed jaw, set the work stop, clamp the part and check…