How to Use a Serger for Beginners
Learn how to use a serger for beginners: threading, tension, practice seams and thread choices, explained step by step.

On this page
A serger finishes a raw fabric edge and sews a seam while it trims the edge, so hems and knit garments look clean inside and out. Learning how to use a serger for beginners starts with threading the machine in the right order, setting the tension so the stitches sit flat, and practicing on scrap fabric before cutting into a real project. This guide walks through each move in order, with thread choices for the fabrics beginners sew most.
As an Amazon Associate I earn from qualifying purchases. LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Thread lengths, weights and needle sizes in this guide come from the thread makers’ own published figures. Serger settings vary by machine, so use the manual that came with the serger when a setting differs from the general guidance here.
Step 1: Learn what a serger does
A serger, also called an overlock machine, sews a seam while a blade trims the raw edge and loopers wrap thread around it. The result is a finished edge that resists fraying, which is why sergers are common for knit garments, activewear and home decor. A serger does not replace a regular sewing machine: it has no bobbin and it does not sew a straight lockstitch for topstitching, so most sewists keep a regular machine beside it. If the difference is still unclear, read serger vs sewing machine and how a serger sewing machine works before threading.
Step 2: Pick thread made for a serger
Serger thread usually comes on large cones, and the common weight is 40S/2 (Tex 27) spun polyester. Cones hold 1600 yards, 1800 yards, 3000 yards, 5500 yards or 6000 yards each, and packs hold 4, 5, 8, 12 or 14 cones. A 4-cone pack in a single color covers a full threading, since many sergers take the same color on each thread path. Polyester thread suits most fabrics, while mercerized cotton thread at 50S/3, given as 30WT and Tex 33 for three plies, suits natural fabrics such as cotton and linen. Cotton thread is thicker than normal 40 weight thread, so the maker recommends needles with a large eye, size 80/12 or larger, and a slower stitching speed when thread breaks. For a first spool, a 3000-yard cone lasts through many practice seams, and a 12-cone set in assorted colors covers most garment projects.
Step 3: Thread the loopers before the needles
Thread the upper looper, then the lower looper, then the needles, following the color-coded path printed on the machine. Raise the presser foot so the tension discs open, and seat each thread in the tension discs. Keep the thread tails long enough to hold while the machine starts, and turn the handwheel to check that the loopers and needles move without catching. A thread stand helps when a spool has a locking base and the machine has no horizontal spool feed: the stand leads thread from the spool to the machine. For part names, see serger parts.
Step 4: Set the tension and check the stitch
Start with the tension dials at the middle mark the manual shows, then sew a line on scrap fabric and look at the edge. Loops hanging off the edge mean a looper tension is loose; puckered fabric means a tension is tight. Move a single dial a small amount, sew again and compare. The goal is a flat seam with the needle and looper threads meeting at the fabric edge. When the stitch looks wrong on a single side, adjust the dial for that thread path and leave the rest alone. Tension trouble that will not clear may point to a threading error, so re-thread from the start before changing more dials. The sewing machine tension guide explains the same idea for a regular machine.
Step 5: Practice on scrap fabric
Sew straight lines, curves and corners on scrap pieces of the fabric planned for the project. Watch how the blade trims the edge and how the feed moves the fabric, and keep hands clear of the blade and needles. Practice turning a corner by stopping with the needles down and pivoting the fabric, and practice ending a seam by chaining off the edge. Keep the practice pieces to compare tension settings side by side.
Step 6: Serge a real seam
Pin or clip the fabric layers with right sides together, line the raw edge up with the blade, and sew at a steady pace, letting the feed move the fabric. Do not pull the fabric through: pulling stretches the seam and bends needles. At the end, chain off the edge and trim the thread chain, then press the seam flat. For a garment, serge each seam as it is sewn, and finish hems with the same overlock stitch. If a seam puckers or the edge rolls, go back to Step 4 and check the tension on scrap first.
Step 7: Store thread and keep the serger clean
Keep cones upright and covered when they are not in use: some packs include dust bags for each cone, and the AOFITOA pack includes 14 dust bags for its 14 cones. A locking-base spool keeps thread tails from unwinding, and a snapping spool without a horizontal feed needs a thread stand. Brush lint from the loopers and the blade area after sewing, and oil only where the manual shows. A thread holder keeps cones feeding smoothly; see best serger thread holder for options.
Common mistakes to avoid
- Threading the needles before the loopers, which tangles the stitch from the start.
- Using regular sewing thread spools that run out mid-seam instead of large cones.
- Pulling the fabric through the machine instead of letting the feed move it.
- Skipping practice seams and cutting into good fabric before the tension is set.
- Sewing with a needle size that strips thick cotton thread; use a large-eye needle, size 80/12 or larger, for mercerized cotton thread.
How to use a serger for beginners: the short version
- Learn what the overlock stitch does and how a serger differs from a sewing machine.
- Pick 40S/2 (Tex 27) polyester thread on cones for most fabrics.
- Thread the loopers, then the needles, following the path on the machine.
- Set the tension, sew on scrap fabric and adjust a single dial at a time.
- Serge the seam at a steady pace and let the feed move the fabric.
- Store cones covered and brush lint from the loopers after sewing.
FAQ: lasers and CNC
What thread should a beginner use in a serger?
Start with 40S/2 (Tex 27) spun polyester thread on cones. That weight suits woven and knit fabrics, and cones hold 1600 yards to 6000 yards, so a single cone lasts through many practice seams. Use one color across all thread paths for a first project.
How much thread does a serger use?
A serger uses more thread than a sewing machine because loopers wrap thread around the edge as well as sewing the seam. A 3000-yard cone is a practical size for practice, and packs of 4 cones in one color cover a full threading. For long projects, cones of 5500 yards or 6000 yards each cut down on reloading.
Can a beginner use cotton thread in a serger?
Yes, mercerized cotton thread works for natural fabrics such as cotton and linen. New brothread gives 50S/3 thread, 600M (660Y) per spool, at 30WT and Tex 33 for three plies. Because cotton thread is thicker than normal 40 weight thread, use needles with a large eye, size 80/12 or larger, and slow the stitching speed if thread breaks.
Do I need a special needle for a serger?
A serger takes its own needle system, so fit the needle type the manual shows and change it when it dulls. For thick mercerized cotton thread, the maker recommends a large-eye needle, size 80/12 or larger, to stop the thread stripping. See sewing machine needle sizes and best sewing machine needle for cotton for needle charts.
What is the difference between a serger and a coverstitch machine?
A serger trims and finishes a raw edge while it sews a seam. A coverstitch machine sews a coverstitch hem without trimming, which is why it is common for hems on knit garments. Many sewists keep a serger for seams and a coverstitch machine for hems. Read coverstitch vs serger for a closer comparison.
Can I use a serger on woven fabric?
Yes. Sergers finish seams on woven fabrics such as cotton, linen and denim, and on knits. Set the tension for the fabric in use and sew a practice seam on scrap first, since tension that suits a knit may pucker a woven.
Related: the sewing and embroidery machine hub, serger machine for beginners and best beginner serger. Also see serger troubleshooting. Also see how to set a sewing machine.




