How to Tap and Die: Cut Clean Threads by Hand
Cut internal and external threads by hand: pick the tap or die size, start it straight, and reverse to clear chips, with 4 SAE and metric sets to choose from.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
toolant 127-Piece Metric & SAE Ratcheting Tap9.7/10View on Amazon - 2
OMT Tap and Die Set, SAE and Metric Thread Repair9.7/10View on Amazon - 3
60-Pc Master Tap and Die Set9.6/10View on Amazon - 4
GEARWRENCH 77 Piece SAE/Metric Ratcheting Tap9.6/10View on Amazon
A stripped bolt hole or a rod that needs threads is a common shop job, and how to tap and die is the skill that fixes it: a tap cuts internal threads in a hole, and a die cuts external threads on a rod. The steps below walk through picking the size, starting the cut straight, and clearing the chips, with SAE and metric sets to choose from.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

toolant 127-Piece Metric & SAE Ratcheting Tap
A 127-piece SAE and metric ratcheting tap and die set with drill bits, tap holders and a double-layer toolbox.
Pros
- 127 pieces, the largest set here
- Ratcheting T-handles with a 5-degree swing arc
- Drill bits matched to each tap size
- 1 year warranty on the main tool body
Cons
- No size list is stated for the taps and dies
- Accessories carry only 180 days
- No steel grade is stated
- No thread pitch gauges are stated

OMT Tap and Die Set, SAE and Metric Thread Repair
An 80-piece SAE and metric tap and die set with 68 taps and dies, wrenches, pitch gauges and a 1 year warranty.
Pros
- 80 pieces with 68 taps and dies
- Coarse and fine taps and dies, M3 to M12 and #4 to 1/2 inch
- Gloves, wrenches, screwdrivers and pitch gauges included
- 1 year warranty
Cons
- No ratcheting handles
- No drill bits included
- No stated hardness figure
- SAE and metric sets store in separate cases

60-Pc Master Tap and Die Set
A 60-piece SAE and metric tap and die set in GCr15 bearing steel, heat treated to 60 HRC.
Pros
- GCr15 bearing steel, heat treated to 60 HRC
- Sizes listed in full: 20 metric, 20 SAE coarse, 12 SAE fine, 2 NPT
- Tapered teeth for easier starts
- Adjustable tap and die handles plus 2 pitch gauges
Cons
- No warranty term is stated
- No ratcheting handles
- Hand use only, no power tools
- No drill bits included

GEARWRENCH 77 Piece SAE/Metric Ratcheting Tap
A 77-piece SAE and metric ratcheting tap and die set with Twist Lock guides and a 5-degree swing arc.
Pros
- Ratcheting T-handles with a 5-degree swing arc
- Twist Lock guide keeps dies centered
- Reversing lever ends hand-over-hand turning
- 77 pieces, SAE and metric
Cons
- No warranty: a consumable item
- No size list is stated for the taps and dies
- No drill bits or pitch gauges included
- No stated steel grade
How to tap and die: pick the size
Match the tap to the hole and the die to the rod: the size you need is the size of the bolt or nut the thread must fit. The OMT and EFFICERE sets cover M3 to M12 and #4 to 1/2 inch, in coarse and fine threads, and the EFFICERE set also lists 1/8-27 NPT taps and dies. Both sets include thread pitch gauges, which find the thread pitch before the cut.
Check the pitch with the gauge, then pick the matching tap or die from the case. The toolant set adds drill bits matched to each tap size, so the hole and the thread match without checking a separate chart.
How to tap and die: start the cut straight
Hold the tap or die square to the work and turn it in slowly so the thread starts true. The GEARWRENCH and toolant sets use ratcheting T-handles with a 5-degree swing arc and a reversing lever, so the hand stays in place in tight spaces. The Twist Lock guide on both sets keeps the dies centered while cutting.
Turn forward, then reverse to clear the chips before continuing. A tap or die that starts at an angle cuts a thread that runs off square, so check the angle before the cut goes deep.
How to tap and die: clear the chips
Chips pack into the cut and jam the tool, so clear them often. If a tap or die jams, do not force it: reverse direction to clear the chips and debris before continuing, since forcing it may break the tool. A drop of tapping fluid on the tap helps the cut; see our best metal tapping fluid guide.
The EFFICERE set states hand use only and warns against power tools, which can damage the threads with too much torque. The other sets are hand tools too.
How to tap and die: match the set to the metal
The OMT set lists wood, copper, aluminum, iron and steel, and the EFFICERE set lists carbon steel, cast iron, aluminum, brass, copper and stainless steel. Pick the set that lists the metal on the bench. The toolant set meets ISO3/2B tolerance for 6H grade nuts.
The tap and die sets in this guide
The size range and the handles decide the set: pick the kit that holds the sizes you need, with the handles that suit the space.
Common mistakes to avoid
- Forcing a jammed tap or die instead of reversing to clear the chips.
- Using power tools on hand taps and dies.
- Starting the tap or die at an angle, so the thread runs off square.
- Picking the wrong size for the bolt or rod.
How to tap and die: the short version
- Pick the size with a pitch gauge.
- Start the tap or die straight.
- Turn forward, then reverse to clear the chips.
- Check the thread against the bolt or nut.
FAQ: lasers and CNC
What is the difference between a tap and a die?
A tap cuts internal threads in a hole, and a die cuts external threads on a rod. The OMT set states both internal and external threading, and the EFFICERE set states the same split: taps for internal threads and dies for external threads.
What sizes do tap and die sets cover?
The OMT and EFFICERE sets cover M3 to M12 and #4 to 1/2 inch, in coarse and fine threads. The EFFICERE set also lists 1/8-27 NPT taps and dies.
Can I use a tap and die set with power tools?
The EFFICERE set states hand use only and warns against power tools. The other sets are hand tools too, so use them by hand.
What do I do if a tap jams?
Do not force it. The OMT set says to reverse direction to clear the chips and debris before continuing, since forcing it may break the tool.
Do tap and die sets come with a warranty?
The OMT set states a 1 year warranty, and the toolant set states 1 year on the main tool body and 180 days on accessories. The EFFICERE set states no warranty term, and the GEARWRENCH set states no warranty.
Related: the CNC tooling hub and our best metal tapping fluid guide.




