Custom Size Cutting Mats for Craft Cutting Machines
Custom size cutting mats match the mat to the machine and the material, with 12x12 sticky areas, four tack levels and whole-mat sizes to check before ordering.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Caydo 2.25 Inch Electric Button Maker Machine for Custom Pins9.7/10View on Amazon - 2
Green 58mm9.4/10View on Amazon - 3
MK.Bear Button Maker Machine Multiple Sizes 200 Pcs,Pin Maker9.5/10View on Amazon
Cutting vinyl decals, cardstock cards and fabric pieces for a craft fair table starts with a mat that holds the material still while the blade moves. When the mat is the wrong size or the wrong stickiness, the material slips, lifts or tears, and the cut comes out wrong. Custom size cutting mats solve that mismatch by matching the mat to the machine and the material, so the sticky area, the whole mat size and the tack level all fit the job at hand.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
The listings behind this guide sell standard sizes, not made-to-order mats, so custom size here means choosing the standard size and stickiness that fits a given machine and material.
Custom size cutting mats: what the size really means
A cutting mat has a sticky area where the material sits, and a whole mat that feeds through the machine, and both sizes matter. Most mats in this guide list a 12×12 sticky area, which WORKLION lists as 305x305mm, while the whole mat runs larger. WORKLION lists the whole mat at 13×14, REALIKE lists the whole mat at 13.95×12.99, and AIRCUT lists the whole mat at 14×13. Brother lists its ScanNCut mat at 13.78×17.71. Cricut lists its LightGrip mat at 30.5 cm x 30.5 cm for the sticky area. The exception is the Cricut Joy size: Cricut lists a 4.5×12 mat, or 11.4 cm x 30.5 cm, for Joy machines. Measure the machine opening and the material before ordering, and match both sizes, not just the sticky area.
Step 1: Match the mat to the machine
Start with the machine, because a mat made for a different machine will not feed right. Mats listed for Cricut Maker and Explore machines use a 12×12 sticky area, and Cricut lists its LightGrip mats for Explore and later and Maker and later. Cricut lists its Joy mats at 4.5×12 for Joy and later, so a Joy mat will not cover a Maker job. Brother lists its ScanNCut DX mat for Brother cutting machines, and Brother states that buyers should always check cutting machine compatibility before ordering. When the machine name is missing from the mat listing, skip that mat and look for a listing that names the machine. Compare the standard sizes in the best 12×12 cutting mat for cutting machines guide before ordering.
Step 2: Pick the stickiness for the material
The listings group stickiness into light, standard, strong and fabric. Light mats suit lightweight materials: REALIKE lists office paper, cardstock, vellum and vinyl for its light mat, and Cricut lists paper, thin cardstock and printable materials for its LightGrip mats. Standard mats suit medium-weight materials: HTVRONT lists pattern paper, cardstock, pearl paper, vellum and HTV vinyl for its standard mat, and THANMAO lists cardstock, construction paper, vellum and vinyl for its standard mat. Strong mats suit heavyweight materials: REALIKE lists thick cardstock, craft foam, chipboard, magnet material and poster board for its strong mat. Fabric mats suit fabric, cotton, felt and leather, as WORKLION lists for its fabric mat. When the material is not listed for a tack level, do not jump to the strong mat: a strong mat can tear thin paper on removal, so match the tack to the material weight instead.
Step 3: Check the pack and the extras
Mats sell in packs, and the pack decides how many spares sit on the shelf. WORKLION lists a variety pack of 6 with 3 standard mats, a fabric mat, a light mat and a strong mat. HTVRONT, REALIKE and THANMAO list packs of 3, and AIRCUT lists a variety pack of 3 with light, standard and strong mats. Cricut lists a LightGrip pack of 6 and a Joy variety pack of 5 with 2 StandardGrip mats and 3 LightGrip mats. Brother lists a single mat. Several listings mention a scraper and a spatula for lifting cut pieces, and HTVRONT lists a free scraper with its pack. Count the mats in the pack before ordering, and match the pack to how often the mat gets used. The best Cricut cutting mat guide compares the Cricut packs side by side.
Step 4: Keep the mat sticky
A mat stays sticky when the clear film cover stays on it between jobs. WORKLION, HTVRONT, REALIKE, THANMAO and AIRCUT all list keeping the clear film cover on the mat when storing, to keep the mat free from paper scraps and dust. Use the scraper to clear excess pieces and the spatula to lift cut images, as the listings describe. THANMAO lists that the film can be torn off and stuck back on about 50 times with good storage, and about 10 to 30 times when the glue sits open to the air for a long time. When the mat stops holding material flat, clean the surface and let it dry, then cover it again before storing.
Common mistakes to avoid
- Buying a 4.5×12 Joy mat for a Maker or Explore machine.
- Putting a strong mat under thin paper that tears on removal.
- Using a Brother mat on a Cricut machine, or a Cricut mat on a Brother machine.
- Leaving the clear film off the mat between jobs, so dust and scraps kill the tack.
- Judging a mat by the sticky area alone and forgetting the whole mat size.
Custom size cutting mats: the short version
- Match the mat to the machine: 12×12 for Maker and Explore, 4.5×12 for Joy, Brother mats for Brother machines.
- Pick the tack by material weight: light for lightweight, standard for medium-weight, strong for heavyweight, fabric for fabric.
- Check the whole mat size: 13×14, 13.95×12.99 and 14×13 are all listed whole-mat sizes.
- Count the pack: packs of 6, 5, 3 and single mats are all listed.
- Keep the film cover on between jobs.
FAQ: lasers and CNC
Can I cut a cutting mat to a custom size?
The listings sell standard sizes and give no cutting instructions, so treat the mat as a fixed size: buy the 12×12 sticky area for Maker and Explore machines, or the 4.5×12 size for Joy machines, and check the whole-mat size before ordering.
What size cutting mat do I need for a Cricut Maker?
A 12×12 sticky area fits Maker machines, and Cricut lists its LightGrip mats for Maker and later. Check the whole mat too: WORKLION lists 13×14, REALIKE lists 13.95×12.99, and AIRCUT lists 14×13. Match the whole-mat size to the space on the desk and the machine opening.
Which stickiness should I use for vinyl?
Vinyl sits in both the light and standard lists, so match the tack to the vinyl weight. Cricut lists vinyl under its LightGrip mats for lightweight materials, while HTVRONT and THANMAO list vinyl under standard mats for medium-weight materials. When in doubt, start with standard tack and move to light tack for thin vinyl.
Do cutting mats work with Brother ScanNCut machines?
Only the Brother mat in this guide is listed for Brother machines: Brother lists its ScanNCut DX mat for Brother cutting machines. Cricut mats are listed for Cricut machines, and Brother states that buyers should always check cutting machine compatibility before ordering.
How many mats come in a pack?
Packs vary by listing. WORKLION lists a variety pack of 6, Cricut lists a LightGrip pack of 6 and a Joy variety pack of 5, HTVRONT, REALIKE, THANMAO and AIRCUT list packs of 3, and Brother lists a single mat.
How do I keep a cutting mat sticky?
Keep the clear film cover on the mat when storing, and use the scraper and spatula to lift cut pieces. THANMAO lists that the film can be torn off and stuck back on about 50 times with good storage, and about 10 to 30 times when the glue sits open to the air.
Related: the best 12×12 cutting mat for cutting machines, the best Cricut cutting mat, the cutting machines hub and the craft machines hub. Also see how to cut heat transfer vinyl.




