Best Wood Ornaments for Laser Engraving (2026): 4 Packs

Specs compared

Specifications are manufacturer rated as listed, collected 19 October 2026.

Buying guide: best wood ornaments for laser engraving

Surface and finish

Both OurWarm listings state the discs are laser cut and polished with both sides sanded smooth, ready for painting, staining or engraving. The Blulu states a lightweight smooth natural wood surface. The KXEXK states pure natural pine with a smooth surface, clear texture and bark edges. For engraving contrast, the smoother the blank, the cleaner the burn. The KXEXK pine keeps its bark edge, which the listing presents as a feature; the other three are clean rounds. Bark edges look rustic but can shed flakes in the laser bed, so brush them off before engraving.

Size and thickness

Diameters run 3 inches on the OurWarm 30-pack, 3.5 inches on the OurWarm 100-pack and the Blulu, and 3.2 to 4 inches on the KXEXK. Thickness runs 0.1 inch on the OurWarm packs, 2.5 mm on the Blulu and 0.4 inch on the KXEXK, the thickest here. All four fit small laser beds; the KXEXK bark-edge slices need a little more clearance. Thickness decides the project: the 0.4 in KXEXK slices are four times the 0.1 in OurWarm thickness (0.4 / 0.1 = 4), which suits coasters and trivets, while the thin discs suit hanging ornaments that must stay light on the branch.

Predrilled or drill yourself

Three listings arrive predrilled: both OurWarm packs with jute twine included and the Blulu with cords. The KXEXK is not predrilled but includes a hand twist drill, two sharp drills and 24 meters of hemp rope. If the ornaments must hang on the tree the day they are engraved, predrilled wins. The KXEXK drill is a hand twist drill, so expect slow going through 0.4 in pine; drill before engraving so dust does not settle on a finished design.

Ornament blanks vs plain wood slices

Three of the four listings sell finished ornament blanks: predrilled, sanded and paired with hanging cord. The KXEXK sells raw pine slices with bark edges, no holes, plus the drill and rope to finish them yourself. Blanks suit engraving runs where every piece must match; raw slices suit rustic projects where variation is the point. The KXEXK diameter varies 3.2 to 4 in, while the OurWarm and Blulu discs are uniform rounds. Uniformity matters when every ornament in a set must look the same on the tree; the KXEXK variation suits one-off gifts where no two match.

Hanging hardware compared

The OurWarm 30-pack includes 30 jute twine pieces and the 100-pack includes 100, one per ornament. The Blulu includes a cord per piece, stated at about 35 cm or 13.7 in long. The KXEXK includes 24 meters of hemp rope plus a hand twist drill and two drills, since its slices arrive undrilled. If the ornaments must hang the day they are engraved, the predrilled packs with included cord win; if you cut cord to custom lengths, the 24 m rope goes further. The OurWarm twine is jute, the KXEXK rope is hemp, and the Blulu cord is unstated beyond its length; match the fiber to the look you want, rustic jute, natural hemp or plain cord.

What the listings tell you

We read 4 ornament listings. All four state natural or pine wood; three state predrilled holes; three include hanging cord or twine. Stated thickness runs 0.1 in on the OurWarm packs, 2.5 mm on the Blulu and 0.4 in on the KXEXK. Stated weights run 0.21 kg, 1.6 ounces and 2.8 kg, with one listing stating no weight. None of the four state a warranty term or a safety certification. Two listings state the discs are laser cut and polished. The Blulu states its ornaments are lightweight at 1.6 ounces for the pack, and the KXEXK states 2.8 kg for 80 thick slices; weight follows thickness here.

Storing blanks and finished ornaments

The listings state no storage guidance, so go with shop sense: keep blanks flat and dry, stacked with the holes aligned so nothing warps against a neighbor. Unfinished wood moves with damp air, so a sealed bin beats an open shelf in a humid shop. Finished ornaments with twine attached tangle; bundle them in sets of ten with a twist tie before they go in the market box.

Count per pack and batch planning

Counts run 30, 60, 80 and 100 pieces. The OurWarm 100-pack suits market-stall batches and classrooms; the 30-pack suits a single tree or a gift-tag run. The Blulu 60-pack splits the difference with shaped designs. The KXEXK 80-pack suits rustic batches where each slice differs. Match the count to the project so blanks do not sit in a drawer for years.

Project Match

• Coasters and gift tags: the OurWarm 30-pack, predrilled 3 in discs with twine.
• Market-stall batches: the OurWarm 100-pack, the most blanks per order.
• Rustic bark-edge ornaments: the KXEXK pine slices, 0.4 in thick.
• Shaped ornaments: the Blulu snowflake and angel set with cords.
• Wedding table numbers: the OurWarm 100-pack, uniform 3.5 in discs with twine.
• Gift tags: the OurWarm 30-pack, small 3 in blanks that take a name well.
• Rustic coasters: the KXEXK 0.4 in slices, thick enough to sit flat.

How the scores add up

Each pack is scored on performance, build, value, safety and warranty, using only what the listing publishes. For blanks, performance means stated engraving readiness, surface finish and size range. None of the four listings state a warranty term or a safety certification. The weights are on our How We Pick page.

Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.

FAQ: lasers and CNC

Can you laser engrave wood ornaments?

Yes. The OurWarm listings state the discs are laser cut and polished, with a blank surface ready for engraving. Unfinished wood takes the beam well.

What size ornaments engrave best?

The listings here run 3 to 4 inches in diameter, which fits small laser beds. The Blulu 3.5 in and the OurWarm 3 in and 3.5 in drop onto most beds.

Do I need to sand before engraving?

The OurWarm listings state both sides are sanded smooth. The Blulu states a smooth surface. The KXEXK states a smooth surface with bark edges.

Predrilled or plain?

Three listings here are predrilled with hanging hardware included. The KXEXK is not predrilled but includes a hand twist drill and 24 meters of hemp rope.

Wood ornaments or wood slices for engraving?

Ornaments come predrilled with hanging hardware for tree-ready gifts; plain slices suit coasters and signs. See our wood blanks for signs.

How do I hang the KXEXK slices?

Drill a hole with the included hand twist drill, thread the 24 m hemp rope through, and knot it. The predrilled packs skip this step: thread the included jute twine or cord through the existing hole.

More laser and CNC guides

Also see our best basswood for laser engraving. Also see our best wood keychain blanks for engraving. Also see our wood blanks for signs. Also see our basswood vs poplar for laser cutting.