Best Magnetic Cutting Mat Under $40 (2026): 4 Picks Compared
4 magnetic cutting mats under $40 compared by size, surface, magnets, grid and warranty, from a Big Shot mat to tempered glass work surfaces.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallBAOFALI Glass Craft Mat9.6/10View on Amazon - 2
Best KitUCEC 3-Piece Mat Set9.5/10View on Amazon - 3
Best for Mixed MediaCYFUN Glass Craft Mat9.4/10View on Amazon - 4
Best for Big ShotCraftFIRST Magnetic9.4/10View on Amazon
A stack of card blanks, a set of metal dies and a Big Shot on the bench mean a morning of card making, and the best magnetic cutting mat under 40 is the one that holds the dies still while the machine does its work. We compared magnetic mats and glass mats by stated size, surface, magnets, grid and warranty. Every figure below comes from the Amazon listings, not from our own measurements.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall BAOFALI Glass Craft Mat: Tempered glass, 15.75 by 10.24 in, grid, palette, 2 magnets Check price on Amazon
- Best Kit UCEC 3-Piece Mat Set: Magnetic shim plus 2 polycarbonate pads, grid and ruler Check price on Amazon
- Best for Mixed Media CYFUN Glass Craft Mat: Tempered glass, 15.75 by 10.24 in, heat and scratch resistant Check price on Amazon
- Best for Big Shot CraftFIRST Magnetic: Magnetic mat for Big Shot machines, 6.13 by 8.75 in Check price on Amazon
Machines on the list

BAOFALI Magnetic Glass Craft Mat
A tempered glass craft mat, 15.75 by 10.24 in, with a grid in 1-inch and 1/4-inch increments, a mixing palette and 2 magnets.
Pros
- Tempered glass surface, heat and scratch resistant
- Grid in 1-inch and 1/4-inch increments with center lines
- Mixing palette area of 3.5 by 8.6 in for inks and paints
- 2 magnets included, plus non-slip rubber feet
Cons
- Work area of 8 by 10 in is smaller than the full 15.75 by 10.24 in size
- Do not submerge the board in water, per the listing
- No warranty term is stated
- No cutting pads included, unlike the UCEC set

UCEC 3 Pcs Magnetic Cutting Shim & Cutting Pads
A 3-piece set with a magnetic cutting shim at 9 by 6 in and 2 polycarbonate cutting pads at 8.75 by 6 in, with a grid and ruler.
Pros
- Magnetic shim plus 2 polycarbonate cutting pads in one set
- 0.8 mm magnetic mat holds dies firmly in place
- 3 mm polycarbonate pads for even pressure
- Grid and ruler in inches and centimeters
Cons
- Warranty description reads '1' with no unit, so no warranty term is counted
- Magnetic mat is 9 by 6 in, smaller than the glass mats here
- Pads are 8.75 by 6 in, slightly smaller than the 9 by 6 in shim

Glass Craft Mat for Crafting Measuring Painting
A tempered glass craft mat, 15.75 by 10.24 in, with a measuring grid, a heat and scratch resistant surface and a magnetic surface.
Pros
- Tempered glass, heat and scratch resistant
- 15.75 by 10.24 in work surface
- Non-slip backing keeps the mat in place
- Suits rotary cutters, craft knives and heat tools
Cons
- No magnets included in the listing
- No grid increments stated, unlike the 1-inch and 1/4-inch grid on the BAOFALI
- No warranty term is stated
- Glass is scratch resistant, not scratch proof, per the listing

CraftFIRST 6.13" x 8.75" Standard Magnetic Cutting
A standard magnetic cutting mat, 6.13 by 8.75 in, for Big Shot die cutting machines, with a grid and rulers in inches and centimeters.
Pros
- Strong magnetic surface keeps dies in place
- Grid and rulers in both inches and centimeters
- Fits Big Shot, Big Shot Plus, Big Shot Pro and more
- Use multiple dies at once without them moving
Cons
- Smallest here at 6.13 by 8.75 in
- No warranty term is stated
- Fits die cutting machines, not a general craft surface
Other machines to compare
Magnetic Glass Craft MatCheck price on Amazon
CraftFIRST 8.75" x 15" Magnetic Cutting Mat Strong MagneticCheck price on Amazon
CraftFIRST Large Magnetic Mat 8.6" x 13.5"Check price on Amazon
CraftFIRST 5.87" x 7.75" Magnetic Cutting Mat Strong MagneticCheck price on Amazon
BAOFALI Magnetic Glass Craft Mat; 15.75"x10.24"Heat ResistantCheck price on Amazon
BiraBira Cutting Mat SetCheck price on Amazon
Specs compared
| Cutting Mat | HQ Score | Size | Surface | Magnets | Grid | Warranty |
|---|---|---|---|---|---|---|
| BAOFALI Glass Craft Mat | 9.6/10 | 15.75 x 10.24 in | Tempered glass | 2 included | Inches and cm | Not stated |
| UCEC 3-Piece Mat Set | 9.5/10 | 9 x 6 in | Magnetic shim, polycarbonate pads | Not stated | Inches and cm | Not stated |
| CYFUN Glass Craft Mat | 9.4/10 | 15.75 x 10.24 in | Tempered glass | Not stated | Grid stated | Not stated |
| CraftFIRST Magnetic | 9.4/10 | 6.13 x 8.75 in | Magnetic | Not stated | Inches and cm | Not stated |
These numbers come straight from each maker’s listing and are rated, not measured by us (11 November 2026).
What the listings tell you
We read 4 cutting mat listings. All 4 name a magnetic surface or magnets, and 2 are tempered glass. Only 1 names a warranty, and it reads as a bare “1” with no unit. The UCEC and CraftFIRST spec tables list sizes that do not match the bullets, so read the bullet sizes before ordering.
How to choose the best magnetic cutting mat under 40
Die cutting mat or glass work surface
Start with the job. The CraftFIRST mat and the UCEC set are built for die cutting machines: the CraftFIRST mat holds dies for a Big Shot, and the UCEC set pairs a magnetic shim with 2 polycarbonate pads for die cutting and embossing. The BAOFALI and CYFUN mats are tempered glass work surfaces for cutting, stamping, mixed media, heat embossing and hot glue, not die cutting machine mats.
Size and work area
Measure the bench and the dies before ordering. The BAOFALI and CYFUN glass mats measure 15.75 by 10.24 in, though the BAOFALI work area is 8 by 10 in once the palette area is counted. The UCEC magnetic shim measures 9 by 6 in with pads at 8.75 by 6 in, and the CraftFIRST mat measures 6.13 by 8.75 in for card-size dies.
Grids and rulers
A printed grid saves measuring time. The BAOFALI grid runs in 1-inch and 1/4-inch increments with center lines and corner marks for A2 card sizes, and the grid is printed on the back of the glass so it will not wear off. The CraftFIRST and UCEC mats have grids and rulers in both inches and centimeters. The CYFUN listing names a measuring grid but gives no increments.
Magnets and holding power
Magnets keep dies and templates from shifting mid-cut. BAOFALI includes 2 magnets of 0.78 in, and its metal backing lets magnets hold materials in place. The CraftFIRST mat has a strong magnetic surface, and the UCEC shim holds metal dies firmly in place. CYFUN names a magnetic surface but lists no magnets, so check the listing if loose magnets matter.
Project Match
- Card making with a Big Shot: CraftFIRST Magnetic, 6.13 by 8.75 in, with a grid and rulers in inches and centimeters.
- Die cutting and embossing in one set: UCEC 3-Piece Mat Set, magnetic shim plus 2 polycarbonate pads.
- Mixed media, inks and hot glue: BAOFALI Glass Craft Mat, tempered glass with a palette area of 3.5 by 8.6 in and 2 magnets.
- Stamping and paper cutting on glass: CYFUN Glass Craft Mat, 15.75 by 10.24 in with a magnetic surface.
- Large layouts: Not stated, since the largest work area listed is 8 by 10 in on the BAOFALI.
Cut away from fingers, keep blades sharp, and let the mat sit flat and steady. Do not submerge the BAOFALI glass board in water, and do not press hard with a blade harder than glass, since the CYFUN listing warns that steel files and titanium blades may damage the surface.
How the scores add up
Each mat is scored on performance (size, surface and what it holds), build, value, safety and warranty. For cutting mats, safety points come from named features such as rounded edges and a non-slip base. Only UCEC names a warranty, and it reads as a bare “1” with no unit, so no warranty points were given. How we pick explains the weights.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| BAOFALI Glass Craft Mat | 9.6 | 32 | 22 | 21 | 4 | 0 |
| UCEC 3-Piece Mat Set | 9.5 | 30 | 21 | 22 | 0 | 0 |
| CYFUN Glass Craft Mat | 9.4 | 28 | 21 | 20 | 0 | 0 |
| CraftFIRST Magnetic | 9.4 | 26 | 20 | 20 | 0 | 0 |
Scores never fall under 9.2 or rise above 9.8. A machine’s spot between those limits is set purely by its point total.
FAQ: lasers and CNC
What size magnetic cutting mat do I need?
Match the mat to the machine and the dies. The CraftFIRST mat measures 6.13 by 8.75 in for Big Shot dies, the UCEC shim measures 9 by 6 in, and the BAOFALI and CYFUN glass mats measure 15.75 by 10.24 in.
Do magnetic cutting mats work with a Big Shot?
The CraftFIRST mat lists Big Shot, Big Shot Foldaway, BIGkick, SuperStar, Vogobond 2, Big Shot Plus and Big Shot Pro. The UCEC set works with most universal base plate systems and manual and electric die cutting machines.
Is a glass craft mat good for heat embossing?
Both glass mats list heat embossing among their uses, and both are heat resistant. The BAOFALI adds a mixing palette area of 3.5 by 8.6 in for inks and paints.
Do any of these mats state a warranty?
Only UCEC names one, and it reads as a bare “1” with no unit, so no warranty term is counted here. The other listings state no warranty term.
Can I cut directly on a glass craft mat?
Yes, with care. Both glass mats are scratch resistant, and CYFUN warns the glass is not completely scratch proof and that blades harder than glass may damage it. BAOFALI says not to submerge the board in water.
Related: the best die cut machine for card making, Cricut cutting mat, our cutting machines hub and magnetic cutting mat. Also see our cutting mat for paper crafts. Also see our embossing machine for card making. Also see our craft knife. Also see our cutting mat vs cutting board. Also see our manual die cutting machine.




