Best Magnetic Cutting Mat (2026): 4 Picks for Die Cutting
4 magnetic mats from 5.87 x 7.75 in to 15.75 x 10.24 in, compared by size, magnetic hold, grid lines and the machines each listing names.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallBAOFALI Glass Mat9.6/10View on Amazon - 2
Best ExtendedCraftFIRST 6.13 x 14.639.5/10View on Amazon - 3
Best for CuttlebugCraftFIRST 5.87 x 7.759.4/10View on Amazon - 4
Best Replacement PlatesBiraBira 6 x 9 Mat9.3/10View on Amazon
A die that slips ruins the cut. The paper shifts, the shape lands off center, and a piece meant for a card ends up in the bin. That is the job a best magnetic cutting mat does: it holds the die still while the machine rolls through, so each shape lands where the grid says it should.
This guide compares 4 mats on the size, hold, grid and machines each listing states.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall BAOFALI Glass Mat: The largest mat here at 15.75 x 10.24 in, a tempered glass surface with gridlines in inches and centimeters, and 2 magnets in the pack. Check price on Amazon
- Best Extended CraftFIRST 6.13 x 14.63: A 6.13 x 14.63 in magnetic mat for Big Shot machines, with card-size grids, rulers in inches and centimeters, and room for multiple dies. Check price on Amazon
- Best for Cuttlebug CraftFIRST 5.87 x 7.75: A 5.87 x 7.75 in magnetic mat made for Cuttlebug machines, with card-size grids and rulers in inches and centimeters. Check price on Amazon
- Best Replacement Plates BiraBira 6 x 9 Mat: A 2 pc set of 6 x 9 in magnetic plates, 3 mm thick, for Bira Craft 6 in machines and 2 other 6 in machines. Check price on Amazon
Machines on the list

BAOFALI Magnetic Glass Craft Mat
A 15.75 x 10.24 in tempered glass craft mat with gridlines in inches and centimeters, rulers on all 4 sides, and 2 magnets in the pack.
Pros
- 15.75 x 10.24 in tempered glass surface, the largest mat in this guide
- Heat- and scratch-resistant, with polished edges and rounded corners stated for safety
- Gridlines and measurements in inches and centimeters, with rulers along all 4 sides
- 2 magnets in the pack, plus a mixing palette area of 3.5 x 8.6 in and a work area of 8 x 10 in
Cons
- No warranty term is stated
- No machine compatibility is stated: it is a hand-work surface, not a machine plate
- Do not submerge the board in water when cleaning it
- At 15.75 x 10.24 in it needs a large flat table

CraftFIRST 6.13" x 14.63" Extended Magnetic
A 6.13 x 14.63 in extended magnetic mat for Big Shot machines, with card-size grids, rulers in inches and centimeters, and room for multiple dies.
Pros
- 6.13 x 14.63 in extended surface for larger projects
- Fits Big Shot, Big Shot Foldaway, BIGkick, SuperStar, Vogobond 2, Big Shot Plus and Big Shot Pro machines
- Strong magnetic surface keeps dies in place and allows multiple dies at once
- Card-size marking grids and rulers in inches and centimeters
Cons
- No warranty term is stated
- No grid size is stated apart from the full 6.13 x 14.63 in size
- The 6.13 x 14.63 in size needs a machine with a wide opening
- Only 1 mat in the pack

CraftFIRST 5.87" x 7.75" Magnetic Cutting Mat
A 5.87 x 7.75 in magnetic mat made for Cuttlebug machines, with card-size grids, rulers in inches and centimeters, and room for multiple dies.
Pros
- 5.87 x 7.75 in size made for all versions of Cuttlebug machines
- Strong magnetic surface keeps dies in place during cutting
- Multiple dies at once without moving about or colliding, per the listing
- Card-size marking grids and rulers in inches and centimeters
Cons
- No warranty term is stated
- The smallest mat in this guide at 5.87 x 7.75 in
- No thickness is stated apart from the 0.08 in figure in the spec table
- Only 1 mat in the pack

BiraBira Magnetic Cutting Mat Replacement Cutting
A 2 pc set of 6 x 9 in magnetic plates, 3 mm thick, for Bira Craft 6 in machines and 2 other 6 in machines.
Pros
- 2 plates in the set, each 6 x 9 in and 3 mm thick
- Works with Bira Craft 6 in magnetic machines and adjustable machines
- Also compatible with We R Memory revolution and Gina K intri-cut 6 in machines
- Magnetic surface makes an accurate cut every time, per the listing
Cons
- The listing promises satisfaction but states no warranty length
- No grid or ruler is stated
- The 6 x 9 in size fits only 6 in machines
Other machines to compare
BAOFALI Magnetic Glass Craft Mat; 15.75"x10.24"Heat ResistantCheck price on Amazon
GLASSBOARD STUDIO True White Glass Craft MatCheck price on Amazon
CraftFIRST 8.75" x 15" Magnetic Cutting Mat Strong MagneticCheck price on Amazon
CraftFIRST Large Magnetic Mat 8.6" x 13.5"Check price on Amazon
BiraBira Cutting Mat SetCheck price on Amazon
anezus Self Healing Cutting Mat for Rotary CuttingCheck price on Amazon
Specs compared
| Model | HQ Score | Size | Thickness | Magnets | Grid | Machines |
|---|---|---|---|---|---|---|
| BAOFALI Glass Mat | 9.6/10 | 15.75 x 10.24 in | Not stated | 2 magnets included | Inches and centimeters, 1 in and 1/4 in increments | Not stated |
| CraftFIRST 6.13 x 14.63 | 9.5/10 | 6.13 x 14.63 in | 1/8 in | Magnetic surface | Card-size grids, in and cm rulers | Big Shot and 6 more named machines |
| CraftFIRST 5.87 x 7.75 | 9.4/10 | 5.87 x 7.75 in | 0.08 in | Magnetic surface | Card-size grids, in and cm rulers | Cuttlebug, all versions |
| BiraBira 6 x 9 Mat | 9.3/10 | 6 x 9 in | 3 mm | Magnetic plate | Not stated | Bira Craft 6 in, We R Memory, Gina K |
We give each product’s specs as its manufacturer rates them; listings read 5 November 2026. Where the spec table lists a different figure, the review states both.
What the listings tell you, and what they leave out
We read 4 magnetic cutting mat listings for this guide. 2 of the 4 state a thickness: the extended CraftFIRST mat at 1/8 in and the BiraBira plates at 3 mm. The Cuttlebug mat gives a 0.08 in thickness only in the spec table.
Only 1 of the 4 listings names a material: the BAOFALI mat is tempered glass. The other 3 state a magnetic surface and a color, but no material. Only 1 of the 4 includes loose magnets: the BAOFALI pack holds 2 magnets.
1 of the 4 listings disagrees with its own spec table: the BiraBira title says 2 pc and 3 mm, while the spec table lists 1 item and a 0.24 in thickness. Trust the title and bullets for the 2 pc set and the 3 mm thickness.
Buying guide: choosing a best magnetic cutting mat
Match the mat to the machine
Start with the machine. The CraftFIRST Cuttlebug mat fits all versions of Cuttlebug machines, the extended CraftFIRST mat fits Big Shot, Big Shot Foldaway, BIGkick, SuperStar, Vogobond 2, Big Shot Plus and Big Shot Pro machines, and the BiraBira plates fit Bira Craft 6 in machines, We R Memory revolution and Gina K intri-cut 6 in machines. The BAOFALI glass mat names no machine: it is a hand-work surface for cutting, stamping and mixed media.
Size and work area
Size runs from 5.87 x 7.75 in for the Cuttlebug mat to 15.75 x 10.24 in for the BAOFALI glass mat, with the extended CraftFIRST mat at 6.13 x 14.63 in and the BiraBira plates at 6 x 9 in. The BAOFALI mat also states a work area of 8 x 10 in and a mixing palette area of 3.5 x 8.6 in.
Hold and multiple dies
Both CraftFIRST mats state a strong magnetic surface that keeps dies in place and allows multiple dies at once without moving about or colliding. The BAOFALI mat holds paper and dies with 2 magnets on a glass surface. The BiraBira plates state a magnetic surface that makes an accurate cut every time, per the listing.
Grids, rulers and card sizes
Both CraftFIRST mats print card-size marking grids and rulers in inches and centimeters. The BAOFALI mat prints gridlines and measurements in inches and centimeters, with rulers along all 4 sides, a grid in 1-inch and 1/4-inch increments, center lines and corner marks for A2 card sizes. The BiraBira plates state no grid or ruler.
Glass or magnetic plate
The BAOFALI mat is tempered glass: heat- and scratch-resistant, with a smooth non-stick surface for paints, alcohol inks, markers, hot glue and wax, and non-slip rubber feet. The other 3 mats are magnetic plates made to run through a die-cutting machine. Pick glass for hand work and mixed media, and a magnetic plate for die cutting.
Glass mats are heavy and hard, and die-cutting machines pinch. Wipe the glass mat clean with water or alcohol, never submerge it, and keep fingers clear of the machine rollers.
Project Match
Match the mat to the project:
- Cuttlebug die cutting: CraftFIRST 5.87 x 7.75, with card-size grids and rulers.
- Big Shot die cutting on larger pieces: CraftFIRST 6.13 x 14.63, with room for multiple dies.
- Cutting, stamping and mixed media by hand: BAOFALI Glass Mat, a 15.75 x 10.24 in glass surface with 2 magnets.
- Replacement plates for 6 in machines: BiraBira 6 x 9 Mat, a 2 pc set at 3 mm thick.
How the scores add up
Each mat is scored on performance, build, value, safety and warranty. A spec the listing does not publish scores nothing. No mat here states a warranty term, so warranty adds nothing here. The BAOFALI mat earns a safety score for the polished edges and rounded corners its listing states for safety.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| BAOFALI Glass Mat | 9.6 | 32 | 22 | 21 | 3 | 0 |
| CraftFIRST 6.13 x 14.63 | 9.5 | 30 | 21 | 20 | 0 | 0 |
| CraftFIRST 5.87 x 7.75 | 9.4 | 28 | 20 | 20 | 0 | 0 |
| BiraBira 6 x 9 Mat | 9.3 | 27 | 18 | 19 | 0 | 0 |
Point totals are scaled so the weakest reads 9.2 and the strongest 9.8, with everything between kept in order.
FAQ: lasers and CNC
What size cutting mat do I need?
Match the mat to the machine and the dies you use. The Cuttlebug mat is 5.87 x 7.75 in, the extended CraftFIRST mat is 6.13 x 14.63 in, the BiraBira plates are 6 x 9 in, and the BAOFALI glass mat is 15.75 x 10.24 in.
What material is a magnetic cutting mat?
Only 1 of the 4 listings names a material: the BAOFALI mat is tempered glass. The other 3 listings state a magnetic surface and a color, but no material. Treat the magnetic plates as machine plates, and the glass mat as a hand-work surface.
Do I need a cutting mat for a Cricut machine?
Not one of these 4. None of the 4 listings names a Cricut machine: the CraftFIRST mats fit Cuttlebug and Big Shot machines, and the BiraBira plates fit Bira Craft 6 in machines and 2 other 6 in machines. For a Cricut machine, look for adhesive machine mats made for that machine.
Can I use more than one die at a time on a magnetic mat?
Yes, on the mats that state it. Both CraftFIRST mats state a strong magnetic surface that allows multiple dies at once without moving about or colliding. The BAOFALI mat holds dies with 2 magnets.
How do I clean a glass craft mat?
Wipe it clean with water, alcohol, or any household product, per the BAOFALI listing. Do not submerge the board in water.
Related: the craft machines hub, best sewing cutting mat, and best double-sided cutting mat. Also see our best cutting machine for cardstock, best cutting machine for Etsy sellers, laser accessories, laser engraver for beginners, and laser cutter types.




