Best 3D Printer Cover (2026): 5 Picks for Clean Storage
Five dust covers for 3D printers compared by stated size, fabric, handles and safety notes, so a stored printer stays clean between runs.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallMeiiy 26x20x20 Cover9.6/10View on Amazon - 2
Best for FLASHFORGE 5MTwoPone FLASHFORGE 5M9.5/10View on Amazon - 3
Best WarrantyLU2000 Ender 17x17x289.5/10View on Amazon - 4
Best LargeLU2000 Large 23x19x289.5/10View on Amazon
A finished print run means a stack of parts to sell: signs, tumblers, leather patches, cut pieces for a customer order. Between runs the printer sits open on the bench, gathering dust, pet hair and the odd splash, and the best 3d printer cover keeps it clean while it waits. We compared the covers in this guide on stated size, stated fabric, handles and the safety notes each listing prints.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Meiiy 26x20x20 Cover: 26 in tall with a top carry handle and a printed storage-only safety warning Check price on Amazon
- Best for FLASHFORGE 5M TwoPone FLASHFORGE 5M: 16 x 15 x 18 in, 600D fabric, double-stitched, handles on both sides Check price on Amazon
- Best Warranty LU2000 Ender 17x17x28: The only stated warranty here: 90 days, with a drawstring bottom Check price on Amazon
- Best Large LU2000 Large 23x19x28: 23 x 19 x 28 in for Ender 3 V2 and Kobra Neo, 210D fabric Check price on Amazon
Machines on the list

3D Printer Dust Cover, Waterproof Protective Cover
A 26 in tall oxford cloth cover with a top carry handle, fine tight stitching, and a printed storage-only safety warning.
Pros
- 26 in height fits most cubic desktop printers
- Top carry handle for lifting the cover off
- Fine tight stitching at all seams
- Washable fabric, wipes clean with a damp cloth
Cons
- No warranty term is stated
- No denier figure is stated for the oxford cloth
- Storage only: never run the printer with the cover on

TwoPone 3D Printer Cover for FLASHFORGE 5M,3D
A 16 in by 15 in by 18 in cover in 600D fabric with handles on both sides, made for the FLASHFORGE 5M range.
Pros
- Handles on both sides for easy lifting
- 600D fabric with double-stitched seams
- Folds flat when not in use
- Washes clean with water or wet wipes
Cons
- No warranty term is stated
- Sized for FLASHFORGE 5M printers, so measure other printers first
- No drawstring or tie at the bottom is stated

LU2000 3D Printer Dust Cover, Waterproof
A 17 in by 17 in by 28 in cover in 210D polyester with a drawstring bottom, made for Ender 3 printers, with a 90 day warranty.
Pros
- The only stated warranty here: 90 days
- Drawstring tie locker on the bottom edges
- Black outer with a silver inner
- Folds for storage and washes with water
Cons
- 210D fabric is lighter than the 600D covers here
- No handle is stated
- Shares most of its bullet text with the larger LU2000 cover
- Sized for Ender 3 printers, so measure other printers first

LU2000 Large 3D Printer Dust Cover, Waterproof
A 23 in by 19 in by 28 in cover in 210D polyester with a drawstring bottom, made for the Ender 3 V2 and Kobra Neo.
Pros
- The largest cover here at 23 in by 19 in by 28 in
- Fits Ender 3 V2 and Anycubic Kobra Neo
- Drawstring tie locker on the bottom edges
- Black outer with a silver inner
Cons
- No warranty term is stated
- 210D fabric is lighter than the 600D covers here
- No handle is stated
- Shares most of its bullet text with the smaller LU2000 cover

3D Printer Cover for ELEGOO Saturn 4 Ultra 16K
A 13.8 in by 13.8 in by 23.2 in cover in 600D nylon with an integrated handle, made for the ELEGOO Saturn 4 Ultra 16K.
Pros
- Smallest footprint here at 13.8 in by 13.8 in
- 600D nylon with encrypted stitching
- Integrated handle for lifting the cover off
- Bottom opening keeps air moving under the cover
Cons
- No warranty term is stated
- The bullets call the size line an air fryer cover size
- Only the dust cover is sold; the printer is for display only
- Sized for the Saturn 4 Ultra, so measure other printers first
Specs compared
| Model | HQ Score | Size | Material | Handles | Fits | Warranty |
|---|---|---|---|---|---|---|
| Meiiy 26x20x20 Cover | 9.6/10 | 26 x 20 x 20 in | Oxford cloth | Top carry handle | Most cubic desktop printers | Not stated |
| TwoPone FLASHFORGE 5M | 9.5/10 | 16 x 15 x 18 in | 600D polyester; bullets say nylon | Handles on both sides | FLASHFORGE 5M, 5M Pro, AD 5M | Not stated |
| LU2000 Ender 17x17x28 | 9.5/10 | 17 x 17 x 28 in | 210D polyester | Not stated | Ender 3, Ender 3 Pro, Ender 3 V2 Neo, Ender 3 Neo | 90 days |
| LU2000 Large 23x19x28 | 9.5/10 | 23 x 19 x 28 in | 210D polyester | Not stated | Ender 3 V2, Kobra Neo | Not stated |
| EiiJugaloo Saturn 4 | 9.5/10 | 13.8 x 13.8 x 23.2 in | 600D nylon | Integrated handle | ELEGOO Saturn 4 Ultra 16K | Not stated |
These numbers come straight from each maker’s listing and are rated, not measured by us (3 November 2026). Size is the cover size the listing states, and a cover that lists no handle has none stated.
What the listings tell you, and what they leave out
We read five dust cover listings for this guide. Only one states a warranty term, the LU2000 Ender cover with 90 days, and only one prints a safety warning, the Meiiy cover with its storage-only notice. Two listings state a 600D fabric and two state 210D polyester, while the Meiiy states oxford cloth with no denier figure. The TwoPone listing disagrees with itself on material: the title says 600D polyester while the bullets say 600D nylon fabric.
One listing also carries a stray label: the EiiJugaloo bullets call the size line an air fryer cover size, though the dimensions match the Saturn 4 Ultra printer it names. Read the size line, not the label, and measure the printer before ordering.
Buying guide: the best 3d printer cover
Measure the printer first
The EiiJugaloo states the smallest footprint here at 13.8 in by 13.8 in, with a 23.2 in height. The TwoPone measures 16 in by 15 in by 18 in. The LU2000 Ender cover measures 17 in by 17 in by 28 in, the Meiiy measures 26 in by 20 in by 20 in, and the LU2000 Large measures 23 in by 19 in by 28 in. Measure the printer on all three sides and pick a cover with room to spare.
Fabric weight: 600D vs 210D
Two covers state 600D fabric: the TwoPone and the EiiJugaloo. Two state 210D polyester: both LU2000 covers. The Meiiy states thick oxford cloth with no denier figure, and fine tight stitching at all seams. The LU2000 Large weighs 0.33 pounds and the LU2000 Ender weighs 0.26 pounds, while the EiiJugaloo weighs 0.4 pounds. The TwoPone and Meiiy state no weight.
Handles and storage
Three covers state a handle: the TwoPone has handles on both sides, the Meiiy has a top carry handle, and the EiiJugaloo has an integrated handle. The two LU2000 covers state no handle, and both use a drawstring tie locker on the bottom edges instead. Every cover here folds for storage when not in use, and every listing says the fabric washes clean with water or a damp cloth.
Storage cover vs enclosure
None of these five covers is an enclosure. The Meiiy listing prints the warning in full: the cover is for storage only, always remove it completely before you power on or run the printer, do not place it over the printer while printing, and high temperature may cause a fire hazard. A dust cover keeps a stored printer clean; it does not hold heat, vent fumes or make a printer safe to run covered.
Dust covers are for storage only. The Meiiy listing warns to remove the cover completely before you power on or run the printer, and states the cover is not a thermal-insulated enclosure. Never run a printer with a cover on it, and keep the cover away from a hot nozzle and heated bed.
Project Match
- FLASHFORGE 5M on the bench: the TwoPone cover at 16 in by 15 in by 18 in, with handles on both sides.
- Ender 3 V2 or Kobra Neo in the workshop: the LU2000 Large at 23 in by 19 in by 28 in.
- Ender 3, Ender 3 Pro or Ender 3 Neo: the LU2000 Ender cover at 17 in by 17 in by 28 in, with the only stated warranty here.
- ELEGOO Saturn 4 Ultra 16K resin printer: the EiiJugaloo cover at 13.8 in by 13.8 in by 23.2 in, with a bottom opening for air circulation.
- A tall cubic printer in a busy shop: the Meiiy cover at 26 in by 20 in by 20 in, with a top carry handle.
How the scores add up
Each cover is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. A factor the listing does not state scores nothing, which is why four of the five covers here score zero on warranty.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Meiiy 26x20x20 Cover | 9.6 | 30 | 21 | 20 | 7 | 0 |
| TwoPone FLASHFORGE 5M | 9.5 | 28 | 21 | 21 | 4 | 0 |
| LU2000 Ender 17x17x28 | 9.5 | 27 | 19 | 19 | 4 | 1 |
| LU2000 Large 23x19x28 | 9.5 | 29 | 19 | 20 | 4 | 0 |
| EiiJugaloo Saturn 4 | 9.5 | 28 | 20 | 19 | 3 | 0 |
Scores never fall under 9.2 or rise above 9.8. A machine’s spot between those limits is set purely by its point total.
FAQ: lasers and CNC
What is a 3D printer cover?
A 3D printer cover is a fabric sleeve that drops over a printer while it sits unused, keeping dust, pet hair, lint and splashes off the machine. The covers in this guide are made of polyester, nylon or oxford cloth, fold for storage, and wash clean with water or a damp cloth.
Can I leave the cover on while printing?
No. The Meiiy listing warns that its cover is for storage only: always remove the cover completely before you power on or run the printer, and do not place it over the printer while printing. High temperature may cause a fire hazard, and the cover is not a thermal-insulated enclosure.
What size cover do I need?
Measure the printer on all three sides, then pick a cover that states a larger size. The covers here run from 13.8 in by 13.8 in by 23.2 in to 23 in by 19 in by 28 in, with the Meiiy the tallest at 26 in by 20 in by 20 in. A loose fit avoids squeezing the printer, which the Meiiy listing calls out by name.
Do I need a 3D printer enclosure?
That depends on what you print. The five covers in this guide are dust covers for storage, not enclosures: the Meiiy listing states its cover is not a thermal-insulated enclosure. If you want to print inside a heated box, look at a purpose-built enclosure instead, such as the picks in our Ender 3 enclosure guide.
Related: the 3D printer hub, enclosure heaters, and the portable fume extractor picks. Also see our 3D printer stands, printer cameras, large enclosures with ventilation, and laser cutter vs 3D printer.




