Acrylic Sheets How to Cut: Tools, Scoring and Snapping
Score a groove along a ruler, then snap the sheet along the groove: this guide covers the steps and the scoring tools that do the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Fiskars 6" Detail Craft Knife9.5/10View on Amazon - 2
Professional Acrylic Plexiglass Sheet Cutter9.5/10View on Amazon - 3
DIYSELF Professional Plexiglass Cutter9.5/10View on Amazon
Acrylic sheets how to cut is a question with a short answer: mark the line, score a groove along a ruler, then snap the sheet along the groove. The scoring tools in this guide work that way, with a hook knife or a scoring cutter carving the groove and the sheet breaking along it once the groove is deep enough, while the craft knife cuts thin material directly. This guide walks through each step, then shows which tool fits which job.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
| # | Product | HQ Score | Buy |
|---|---|---|---|
| 1 | Fiskars 6" Detail Craft Knife | 9.5/10 | Buy on Amazon |
| 2 | Professional Acrylic Plexiglass Sheet Cutter | 9.5/10 | Buy on Amazon |
| 3 | DIYSELF Professional Plexiglass Cutter | 9.5/10 | Buy on Amazon |

Fiskars 6" Detail Craft Knife
A 6 in detail craft knife with an aluminum body and SoftGrip handle, made for precise cuts in cardstock and thin plastic.
Pros
- Aluminum body with a SoftGrip handle for control on detail work
- Cuts cardstock and thin plastic, per the listing
- Takes standard #10, #11, #16 and #17 blades
- Full lifetime warranty, with blades excluded
Cons
- Suited to thin plastic; the listing does not state thicker acrylic sheet cutting
- Includes one #11 blade, with no spare blades in the box
- No blade guard for use is stated; the cap is for storage

Professional Acrylic Plexiglass Sheet Cutter
A hooked scoring knife with a curved handle and 11 blades, made to groove acrylic sheets and snap them along the line.
Pros
- Made to cut acrylic sheets and other plastic sheets, per the listing
- Curved handle with a ridge on the back for snapping the sheet
- 11 blades in total: one in the handle and a box of spares
- Step-by-step scoring and snapping instructions in the listing
Cons
- No warranty term is stated
- No safety feature beyond the tip-care note is stated
- No blade material is stated
- No handle material is stated

DIYSELF Professional Plexiglass Cutter
A plexiglass cutter with 10 SK5 blades, an ABS body and a non-slip TPR grip, made for scoring acrylic sheets to size.
Pros
- SK5 high-carbon steel blade for repeated scoring
- Push-and-release blade change with no tools needed
- Non-slip TPR grip on an ABS body for steadier scoring
- 10 blades included for cut-to-size work
Cons
- No warranty term is stated
- Suited to thin to medium materials; not intended for especially thick material
- No safety feature is stated
- No weight or dimensions are stated
Acrylic sheets how to cut: the score-and-snap method
Score-and-snap is the hand method for straight cuts in acrylic sheets. A hook knife or a scoring cutter carves a thin groove on the surface, and the sheet then breaks along that groove instead of cracking across it. The BAISALJI listing describes the method in full, and the DIYSELF listing describes the same snap along the groove.
Mark the board with a pen first, then set a ruler on the mark. Hold the ruler steady with one hand and draw the hook knife along it with the other, repeating the pass until the groove is deep enough. That sequence comes from the BAISALJI listing, and the groove must be deep enough before the snap.
To snap the sheet, use the ridge on the back of the hook knife. Place the hook knife under the sheet, line the ridge up with the groove, press down on both sides of the groove and split the sheet along it. The listing warns to protect the tip of the knife and keep it off the ground, and to change the blade when the tip loses its edge.
Before the first cut
A pen, a ruler and a steady hand are the whole kit beside the knife itself. Mark the line with a pen, press the ruler flat on the mark, and hold it steady through every scoring pass.
For sheets the scoring tools do not cover, such as thicker material or curved shapes, a machine cut is the other route. The diode laser vs CNC router for acrylic comparison covers that choice.
Gear for cutting acrylic sheets
The scoring step is where the tool matters: a hook knife or scoring cutter that holds a sharp edge and tracks a ruler decides how clean the snap will be.
Safety notes
Scoring knives are sharp by design, so treat the blade with care from the first pass to storage. The Fiskars knife (on Amazon) ships with a protective cap, and the cap belongs on the blade whenever the knife is put away. The BAISALJI listing adds its own caution: protect the tip of the knife and do not let it touch the ground.
Change a blade when the tip loses its edge instead of pressing harder, and keep spare blades in their box until needed.
FAQ: lasers and CNC
Can a craft knife cut acrylic sheets?
A craft knife handles thin plastic, and the Fiskars listing states cardstock, thin plastic, photos, vinyl and canvas. For acrylic sheets, that means thin material and short detail cuts; thicker sheets call for a dedicated scoring tool such as the hook knife or the plexiglass cutter in this guide.
How do you score and snap an acrylic sheet?
Mark the line with a pen, set a ruler on the mark, and draw the hook knife along the ruler until the groove is deep enough. Then set the ridge on the back of the hook knife under the sheet, line it up with the groove, and press down on both sides to split the sheet along the groove.
How many blades come with each tool?
The BAISALJI tool (on Amazon) comes with 11 blades in total. The DIYSELF cutter (on Amazon) comes with 10 SK5 blades. The Fiskars knife comes with one replaceable #11 blade, and it also takes #10, #16 and #17 blades.
Do you need a laser to cut acrylic sheets?
No. Straight cuts in thin to medium sheets are hand work with a scoring tool, and the DIYSELF listing states its cutter suits thin to medium materials. A laser or CNC router fits thicker sheets and curved shapes.
What thickness can a scoring tool handle?
The DIYSELF listing states its cutter suits thin to medium materials and is not intended for especially thick material. The Fiskars listing states thin plastic, and the BAISALJI listing describes acrylic sheets without stating a thickness.
Related: the engraving materials hub and best black acrylic sheet guide.




