Best Aluminum T Track for X-Carve (2026): 5 Picks for Jigs and Fixtures
5 aluminum t-tracks for X-Carve wasteboards and workbenches, from a 36 inch 6 pack to a 48 inch 4 pack and a spliceable 400 mm pair, compared by length, profile, pack and screws.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallHOTTARGET 36in 6 Pack9.7/10View on Amazon - 2
Longest TrackSeekLiny 48in 4 Pack9.6/10View on Amazon - 3
Spliceable Short TrackKETIPED 400mm 2 Pack9.5/10View on Amazon - 4
Aluminum 48 Inch T-Track with Wood ScrewsView on Amazon - 5
Aluminum 48" T-Track for WoodworkingView on Amazon - 6
QWORK Aluminum T TrackView on Amazon - 7
POWERTEC 71359 Aluminum Combo T-Track Miter Track forView on Amazon - 8
2pcs T-Track for Woodworking 24" Red Double-Cut Pre-drilledView on Amazon
A wasteboard that will not hold a workpiece steady turns a clean carve into a ruined panel and a wasted afternoon. Clamps slide, stock shifts, and the bit cuts where it should not. The best aluminum t track for x-carve gives that board a set of straight, repeatable hold-down lanes, so jigs and fixtures sit in the same place on every run. This guide compares aluminum tracks by length, profile, pack size and mounting hardware each listing states.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall HOTTARGET 36in 6 Pack: 6 tracks at 36 inches with 54 screws included, predrilled holes and aluminum alloy 6063. Check price on Amazon
- Longest Track SeekLiny 48in 4 Pack: 48 inch tracks in a 4 pack with 48 screws, predrilled holes and aluminum alloy 6063. Check price on Amazon
- Spliceable Short Track KETIPED 400mm 2 Pack: 400 mm tracks that splice to a longer length, with 3 predrilled holes per track. Check price on Amazon
Machines on the list
Aluminum 36 Inch T-Track with Wood Screws
A 36 inch blue anodized track set with 6 tracks, 54 screws and predrilled mounting holes, in aluminum alloy 6063.
Pros
- 6 tracks at 36 inches with 54 screws included, 9 screws per track
- Aluminum alloy 6063 with a frosted anodized surface, stated for durability and wear resistance
- Predrilled mounting holes for simple installation, per the listing
- Double-cut profile for jigs and fixtures on a workbench
Cons
- No warranty term is stated
- No safety feature is stated
- Bolt fit is not stated in the listing
- Blue is the stated color, with no other color in this listing
T Tracks for Woodworking Aluminum 48 inch Black 4
A 48 inch black anodized track set with 4 tracks, 48 screws and predrilled mounting holes, in aluminum alloy 6063.
Pros
- 48 inch length, the longest track here, in a 4 pack with 48 screws
- Aluminum alloy 6063 with a fine sandblast anodized surface, stated as corrosion resistant
- Predrilled mounting holes for simple installation, per the listing
- Stated fit for 5/16 inch and 1/4 inch t-bolts and 1/4 inch hex bolts
Cons
- Spec table lists 51.18 x 1.57 x 1.57 inches, against bullets stating 48 x 3/4 x 3/8 inches
- No warranty term is stated
- No safety feature is stated
- Black is the stated color, with no other color in this listing
Aluminum 36" T-Track for Woodworking,2PK Double
A 36 inch black anodized track pair with predrilled mounting holes in aluminum alloy 6063, with screws not included.
Pros
- Aluminum alloy 6063 with a fine sandblast black anodized surface, stated for durability and wear resistance
- Stated fit for 5/16 inch and 1/4 inch t-bolts and 1/4 inch hex bolts
- Stated hold-down clamp fits, including 6-3/8 inch by 1-1/4 inch and 5-1/2 inch by 1-1/8 inch sizes
- Predrilled mounting holes for simple installation, per the listing
Cons
- Screws are not included; the listing recommends 6 x 5/8 inch flat head screws bought separately
- No warranty term is stated
- No safety feature is stated
- Hold-down clamp fit is limited to the sizes the listing names
POWERTEC 71119 36 Inch Double-Cut Profile
A 36 inch anodized track pair with a double-cut profile and predrilled mounting holes, in extruded anodized 6463 aluminum.
Pros
- Extruded anodized 6463 aluminum, stated as lightweight with corrosion resistance
- Double-cut profile for hardware versatility, per the listing
- Stated fit for 5/16 inch and 1/4 inch t-bolts and 1/4 inch hex bolts
- Predrilled mounting holes for simple installation, per the listing
Cons
- Installation hardware is not included, per the listing
- Spec table lists 36 x 1 x 1 inches, against bullets stating 3/4 x 3/8 inches
- No warranty term is stated
- No safety feature is stated
2pc Aluminum 400x30mm Double-Cut Profile Universal
A 400 mm grey anodized track pair with 3 predrilled holes per track, spliceable ends and a fit for 19 mm sliders and t-bolts.
Pros
- Tracks splice: 2 or more tracks can be joined to the length needed, with ends precision cut by CNC
- 3 predrilled mounting holes per track for simple fixing
- Stated fit for 19 mm (0.75 inch) sliders and t-bolts, with a width of 30 mm (1.18 inch)
- Anodized aluminum alloy surface, stated as harder and wear resistant
Cons
- Lowest length stated here at 400 mm, so longer runs need splicing
- Alloy grade is not stated; the listing states aluminum alloy only
- Screw count is not stated; the listing states several fixing screws
- No warranty term is stated
Other machines to compare
Aluminum 48 Inch T-Track with Wood ScrewsCheck price on Amazon
Aluminum 48" T-Track for WoodworkingCheck price on Amazon
QWORK Aluminum T TrackCheck price on Amazon
POWERTEC 71359 Aluminum Combo T-Track Miter Track forCheck price on Amazon
2pcs T-Track for Woodworking 24" Red Double-Cut Pre-drilledCheck price on Amazon
Compare the best aluminum t track for x-carve picks
| Model | HQ Score | Length | Profile | Pack | Screws |
|---|---|---|---|---|---|
| HOTTARGET 36in 6 Pack | 9.7/10 | 36 inches | 3/4 x 3/8 inches | 6 tracks | 54 screws |
| SeekLiny 48in 4 Pack | 9.6/10 | 48 inches | 3/4 x 3/8 inches | 4 tracks | 48 screws |
| Hot Favorable 36in | 9.6/10 | 36 inches | 3/4 x 3/8 inches | 2 tracks | Not included |
| POWERTEC 36in 2 Pack | 9.5/10 | 36 inches | 3/4 x 3/8 inches | 2 tracks | Not included |
| KETIPED 400mm 2 Pack | 9.5/10 | 400 mm (15.75 in) | 30 mm (1.18 in) x 12.7 mm (0.5 in) | 2 tracks | Screws included |
Specifications are manufacturer rated, as published on each listing and collected 24 October 2026.
Most t-track listings state the same profile
All 5 tracks here state a double-cut profile, with predrilled mounting holes and an anodized finish. Length is where they part ways: 36 inches, 48 inches and 400 mm, with pack sizes of 6 tracks, 4 tracks and 2 tracks. Screw counts part ways too, from 54 screws in a 6 pack to no screws at all in a pack where the listing says hardware is not included. That spread decides how much board a pack covers.
Buying guide: best aluminum t track for x-carve
Match length to the board
Tracks here run 36 inches, 48 inches and 400 mm. A 48 inch track covers a longer run without splicing, while a 36 inch track suits a shorter board or a layout built from short lanes. 400 mm is the lowest length here, and the listing states that 2 or more of them can be spliced to the length needed, with ends precision cut by CNC. Measure the board.
Check bolt fit before drilling
3 listings state a fit for 5/16 inch and 1/4 inch t-bolts and 1/4 inch hex bolts. The KETIPED listing states a fit for 19 mm (0.75 inch) sliders and t-bolts, with a width of 30 mm (1.18 inch). The HOTTARGET listing states predrilled mounting holes but states no bolt size, so bolt fit for that pack is Not stated. Check the stated fit before drilling.
Count screws and holes
The HOTTARGET pack includes 54 screws, with 9 screws per track, and the SeekLiny pack includes 48 screws with 4 tracks. The KETIPED pack includes several fixing screws, with no count stated, and 3 predrilled mounting holes per track. The Hot Favorable listing states that screws are not included and recommends 6 x 5/8 inch flat head screws, and the POWERTEC listing states that installation hardware is not included.
Read the spec table with care
2 listings contradict themselves between bullets and spec table, and the bullets win under the site rules. The POWERTEC bullets state a profile of 3/4 inch by 3/8 inch, while its spec table lists 36 x 1 x 1 inches. The SeekLiny bullets state 48 inches by 3/4 inch by 3/8 inch, while its spec table lists 51.18 x 1.57 x 1.57 inches. Use the bullet figures.
Material and finish
3 listings state aluminum alloy 6063, and the POWERTEC listing states extruded anodized 6463 aluminum. The KETIPED listing states aluminum alloy with an anodized surface, with no alloy grade stated. Finishes stated include frosted anodized, fine sandblast black anodized and an anodized surface described as harder and wear resistant.
Clamp stock firmly before cutting, keep hands clear of the bit path, and clear chips and dust from the tracks so clamps seat flat. A loose workpiece can shift mid-cut, so recheck hold-downs after each setup change.
Project Match
- Jigs and fixtures on a workbench: the HOTTARGET 36 inch 6 pack, with predrilled holes and 54 screws included, and the Hot Favorable 36 inch 2 pack, with stated bolt and clamp fits.
- Router table and drill press table work: the POWERTEC 36 inch 2 pack, whose listing names router table, drill press table and workbench uses, and the KETIPED 400 mm pair, whose listing names drill press tables, router tables and saw tables.
- Longer wasteboard runs: the SeekLiny 48 inch 4 pack, the longest track here, and the KETIPED 400 mm pair, which the listing states can be spliced to a longer length.
- Short runs and small benches: the KETIPED 400 mm pair, with 3 predrilled holes per track.
X-Carve wasteboard fit: Not stated in any listing. Match track length to the board in the shop, since no listing states an X-Carve bed size.
How the scores add up
Each track is scored on performance, build, value, safety and warranty. Performance covers length, profile and bolt fit. Build covers alloy and finish as stated. Value covers pack size and included screws. Safety and warranty score nothing where a listing states no safety feature and no warranty term, and every listing here falls in that group for safety and warranty.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| HOTTARGET 36in 6 Pack | 9.7 | 32 | 22 | 21 | n/a | 0 |
| SeekLiny 48in 4 Pack | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Hot Favorable 36in | 9.6 | 30 | 21 | 18 | n/a | 0 |
| POWERTEC 36in 2 Pack | 9.5 | 29 | 21 | 18 | n/a | 0 |
| KETIPED 400mm 2 Pack | 9.5 | 28 | 20 | 19 | n/a | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score. Safety counts only for powered gear or where the listing states safety features; where it does not apply, the score is taken over the remaining 90 points.
FAQ: lasers and CNC
What length of aluminum t track fits an X-Carve wasteboard?
No listing here states an X-Carve bed size, so fit is Not stated. Lengths here are 36 inches, 48 inches and 400 mm, and the KETIPED listing states that 2 or more 400 mm tracks can be spliced to the length needed.
Do these tracks fit 1/4 inch and 5/16 inch t-bolts?
The Hot Favorable, POWERTEC and SeekLiny listings state a fit for 5/16 inch and 1/4 inch t-bolts and 1/4 inch hex bolts. The KETIPED listing states a fit for 19 mm (0.75 inch) sliders and t-bolts. The HOTTARGET listing states no bolt size, so its bolt fit is Not stated.
Are mounting screws included?
The HOTTARGET pack includes 54 screws and the SeekLiny pack includes 48 screws, while the KETIPED pack includes several fixing screws with no count stated. The Hot Favorable listing states that screws are not included, and the POWERTEC listing states that installation hardware is not included.
Can short tracks be joined into a longer run?
The KETIPED listing states that 2 or more of its 400 mm tracks can be spliced, with ends precision cut by CNC. No other listing here states splicing, so splicing for the other tracks is Not stated.
What alloy are these tracks made from?
The HOTTARGET, Hot Favorable and SeekLiny listings state aluminum alloy 6063, and the POWERTEC listing states extruded anodized 6463 aluminum. The KETIPED listing states aluminum alloy with an anodized surface and no alloy grade stated.
Related: best aluminum t track for onefinity, best long toggle clamps for cnc, best lubricant for cnc router and the cnc tooling hub.
