Xtool D1 vs Xtool M1: Which One Should You Buy?
Two riser accessories for two different xTool machines, compared on height, workspace, honeycomb support, setup and safety features stated on each listing.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
xTool S1 40W Laser Cutter and Laser Engraver for Tumblers9.7/10View on Amazon - 2
xTool M2 20W Color Craft Laser Engraver9.7/10View on Amazon - 3
xTool M2 20W Laser Engraver9.7/10View on Amazon - 4
xTool M2 40W Color Craft Laser Engraver and CutterView on Amazon - 5
xTool M2 CleanCut PanelView on Amazon - 6
xTool CMYK Inkjet Printing Module for xTool M2View on Amazon - 7
xTool RA3 Lite Rotary Attachment for xTool M2View on Amazon - 8
xTool P2 Honeycomb Working Panel 2.0View on Amazon
Makers who sell signs, tumblers, leather patches and cut parts often hit the same limit: a piece taller than the machine allows. Raising the machine changes what fits under the laser, and the right lift depends on the machine on the bench. This comparison covers xtool d1 vs xtool m1 through the riser accessories each side lists, using only what each listing states.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: the M1 Ultra Riser Base is the fuller riser, with a built-in honeycomb panel, material pins, extra storage, pre-assembled setup and a design that maintains the M1 Ultra enclosed design. The D1 Riser Footpads are the simpler lift, adding height per leg for D1 and D1 Pro machines. Pick by machine first, since each accessory is stated for a different machine family.
Machines on the list
xTool M1 Ultra Riser Base with Honeycomb Panel
A pre-assembled riser base for the M1 Ultra with a built-in honeycomb panel, extra storage and a design that maintains the M1 Ultra enclosed design.
Pros
- Raised workspace for ultra-thick materials up to 125mm, per the listing
- Built-in honeycomb panel of iron and aluminum for smoke exhaust and clean cutting effects on both sides
- Pre-assembled and ready out of the box, with extra storage and 4 pins to hold material in place
- Enclosed design stated to block most smoke, harmful gases and laser light
Cons
- The title dimension and the spec table dimension differ, so check dimensions before planning a layout
- Compatibility is stated for the M1 Ultra only
- Rotary use needs the xTool rotary accessory
- No laser power or cutting specification is stated in the listing
4Pcs Laser Engraver Riser Raiser Footpads
A set of aluminum alloy riser footpads for the xTool D1 and D1 Pro that add height per leg and stack for taller items.
Pros
- Adds 1.77" (45mm) of height per leg for items taller than the height of the machine itself
- Aluminum alloy construction for load bearing, per the listing
- Stackable legs, so height can be increased as needed
- Usable with or without a rotary attachment
Cons
- No warranty term is stated in the listing
- No honeycomb panel or material pins are stated
- No enclosed design or smoke handling is stated
- The title lists 4 pieces while the spec table lists NumberOfItems as 1, so the count needs care
Other machines to compare
xTool M2 40W Color Craft Laser Engraver and CutterCheck price on Amazon
xTool M2 CleanCut PanelCheck price on Amazon
xTool CMYK Inkjet Printing Module for xTool M2Check price on Amazon
xTool RA3 Lite Rotary Attachment for xTool M2Check price on Amazon
xTool P2 Honeycomb Working Panel 2.0Check price on Amazon
Side by side
| Spec | D1 Riser Footpads | M1 Ultra Riser Base | Notes |
|---|---|---|---|
| HQ Score | 54 | 77 | The M1 Ultra base scores higher |
| Fit | xTool D1 and D1 Pro | M1 Ultra | Different machines |
| Taller work | 1.77″ (45mm) of height per leg, stackable | Ultra-thick materials up to 125mm | Different ways of adding height |
| Material | Aluminum alloy | Iron and aluminum | D1 footpads are aluminum alloy; only the M1 honeycomb board is stated as iron and aluminum |
| Honeycomb panel | Not stated | Built in, with 4 pins | Only the M1 listing states a honeycomb panel |
| Rotary use | Usable with or without a rotary attachment | Pairs with the xTool rotary accessory | Both listings mention rotary use |
| Setup | Screw in the threads | Pre-assembled, ready out of the box | The M1 listing states no additional installation |
| Enclosure and smoke | Not stated | Maintains the M1 Ultra enclosed design, blocking most smoke, harmful gases and laser light | Only the M1 listing states enclosure help |
| Warranty | No warranty term stated | 12 Months | Only the M1 listing states a term |
Specifications are manufacturer rated, as published on each listing and collected 2 November 2026.
xtool d1 vs xtool m1: height, honeycomb and setup
The two sides solve height differently. On the D1 side, four aluminum alloy legs screw into threads, each leg adds 1.77″ (45mm) of height, and multiple legs can be stacked to increase height as needed. On the M1 side, a riser base lifts the workspace and the listing states engraving for ultra-thick materials up to 125mm.
Height and taller work
For the D1 footpads, the figure is per leg: 1.77″ (45mm) of added height, with stacking for more height as needed. The listing frames the need plainly: items taller than the height of the machine itself call for a raised foot. The listings do not state the same kind of height figure on both sides, so a direct height winner cannot be named from the listings alone.
Honeycomb and smoke
Only the M1 listing states a honeycomb panel. Its built-in board is made of iron and aluminum, with a uniform honeycomb hole design that the listing states accelerates smoke exhaust and gives clean and neat cutting effects on both sides of the material. Four pins keep material in place. The D1 listing mentions no honeycomb panel or smoke handling, so smoke handling and hold-down are not covered by this listing. For fume handling, see the fume extractor guide.
Setup and fit
The D1 footpads install by screwing in the threads, leg by leg, and stacking legs adds height as needed. The M1 Ultra base arrives pre-assembled and ready out of the box, with no additional installation required, and it adds extra storage so tools stay handy. Fit is strict: the footpads are stated for the xTool D1 and D1 Pro, and the base is stated for the M1 Ultra. Neither listing states a fit for the other machine family.
Safety and enclosure
The M1 listing states that the riser base maintains the enclosed design of the M1 Ultra and blocks most smoke, harmful gases and laser light, with the listing claiming a safer and cleaner working environment than other riser stands. The D1 listing mentions no enclosed design, interlock or flame detection. On either side, never laser PVC or vinyl. For enclosed machines, see best enclosed laser engraver.
Rotary work and curved pieces
Both listings mention rotary use. The D1 footpads can be used whether the machine runs with or without a rotary attachment. The M1 base pairs with the xTool rotary accessory for curved surfaces, naming rings, mugs, tumblers and balls as examples. No rotary accessory is stated as included with either listing.
Choose the M1 Ultra Riser Base if
- The machine on the bench is an M1 Ultra.
- A built-in honeycomb panel with material pins matters.
- Pre-assembled setup and extra storage are preferred.
Choose the D1 Riser Footpads if
- The machine on the bench is a D1 or D1 Pro.
- Simple, stackable height is enough.
- Work runs with or without a rotary attachment.
An enclosed design holds only while the enclosure stays intact. Never defeat a lid or shield, stay with the machine while it runs, keep a fire extinguisher nearby, ventilate, and never laser PVC or vinyl.
Project Match
- Taller flat items on a D1 or D1 Pro: D1 Riser Footpads, stacked as needed.
- Curved pieces such as rings, mugs, tumblers and balls on an M1 Ultra: M1 Ultra Riser Base with the xTool rotary accessory.
- Cut work needing a honeycomb panel and material pins: M1 Ultra Riser Base.
- Materials beyond those named here: Not stated in either listing.
FAQ: lasers and CNC
Can the D1 footpads fit an M1 Ultra?
No fit for the M1 Ultra is stated for the D1 footpads. They are stated for the xTool D1 and D1 Pro, and the riser base is stated for the M1 Ultra.
How much height do the D1 footpads add?
Each leg adds 1.77″ (45mm) of height, and multiple legs can be stacked to increase height as needed. No maximum stacked height is stated.
Does the M1 Ultra riser base include a honeycomb panel?
Yes, per the listing. It has a built-in honeycomb panel of iron and aluminum, with 4 pins to hold material in place, and the listing states clean cutting effects on both sides.
Does either riser need assembly?
The M1 Ultra base is pre-assembled and ready out of the box. The D1 footpads install by screwing in the threads, leg by leg.
Related: how to choose a laser engraver, best laser engraver for beginners and Longer Ray5 vs Xtool S1.
