Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

What Is a Shaft Collar and How Is It Used

A shaft collar locks onto a shaft to hold parts in place; this guide explains the styles, sizes and fitting steps.

What Is a Shaft Collar and How Is It Used
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1AZSSMUK 1" Bore Double Split Shaft Collar BlackAZSSMUK 1" Bore Double Split Shaft Collar Black9.6/10View on Amazon
  2. 2(4-Pack) 1” Bore Solid Steel Shaft Collars(4-Pack) 1” Bore Solid Steel Shaft Collars9.6/10View on Amazon
  3. 3TonGass 8 Pack 5/8 Inch Bore Shaft CollarsTonGass 8 Pack 5/8 Inch Bore Shaft Collars9.6/10View on Amazon
  4. 44pcs 5/8" bore Shaft Collar,Zinc Plated Set-Screw4pcs 5/8" bore Shaft Collar,Zinc Plated Set-Screw9.6/10View on Amazon

What is a shaft collar? It is a ring that fits around a shaft and locks in place, holding parts where they belong and stopping them from sliding along the shaft. When a wheel or bearing keeps drifting out of position, a collar pins it down. This guide explains the styles, the sizes and how fitting works.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Honest note

No listing in this guide states a load rating for its collars, so this guide gives no load figures. Match the bore to the shaft diameter and check the set screw size before ordering.

AZSSMUK 1" Bore Double Split Shaft Collar Black

AZSSMUK 1" Bore Double Split Shaft Collar Black

AZSSMUK9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 in bore double split shaft collar in black oxide carbon steel, sold as a pack of 4 with 8 set screws.

Pros

  • Double split style clamps around the shaft
  • 1 in bore, 1-3/4 in outside diameter, 1/2 in width
  • Black oxide carbon steel
  • Pack of 4 collars with 8 set screws

Cons

  • No warranty term is stated
  • No load rating is stated
  • Only the 1 in bore is listed here
  • Jobs needing more than 4 collars need another pack
(4-Pack) 1” Bore Solid Steel Shaft Collars

(4-Pack) 1” Bore Solid Steel Shaft Collars

AR-PRO9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1 in bore solid steel shaft collar, zinc plated, sold as a pack of 4 with cup-point set screws.

Pros

  • 1 in bore, 1-5/8 in outside diameter, 0.625 in width
  • Cup-point set screws sit flush with the surface
  • Zinc-plated carbon steel
  • Pack of 4 collars covers several shafts

Cons

  • No warranty term is stated
  • No load rating is stated
  • Solid style slides on from the shaft end
  • Only the 1 in bore is listed here
TonGass 8 Pack 5/8 Inch Bore Shaft Collars

TonGass 8 Pack 5/8 Inch Bore Shaft Collars

TonGass9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5/8 in bore zinc-plated carbon steel shaft collar, sold as a pack of 8 with set screws.

Pros

  • Pack of 8 collars covers several shafts at once
  • 5/8 in bore, 1-1/8 in outside diameter, 1/2 in width
  • Zinc-plated carbon steel
  • Rated for 0 to 250 degrees Fahrenheit

Cons

  • No warranty term is stated
  • No load rating is stated
  • Only the 5/8 in bore is listed here
  • Set screw count per collar is not stated
4pcs 5/8" bore Shaft Collar,Zinc Plated Set-Screw

4pcs 5/8" bore Shaft Collar,Zinc Plated Set-Screw

Luyostik9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5/8 in bore solid steel set-screw shaft collar, zinc plated, sold as a pack of 4 with a hex wrench.

Pros

  • 5/8 in bore, 1-1/8 in outside diameter, 1/2 in width
  • Hex wrench included in the pack
  • Needs no tools beyond the included hex wrench
  • Galvanized coated carbon steel

Cons

  • No warranty term is stated
  • No load rating is stated
  • Only the 5/8 in bore is listed here
  • Pack of 4 collars suits smaller jobs

What Is a Shaft Collar?

A shaft collar is a ring with a bore that matches the diameter of a shaft. A solid collar slides onto the shaft from the end, then a set screw locks it in place; a double split collar clamps around the shaft instead. Once locked, it works as a stop, a spacer or a locator, keeping parts from sliding along the shaft.

The makers list automotive work, machinery repair, medical equipment repair, gearbox assemblies, machine tools and wheel barrow axles among the uses.

How a Shaft Collar Works

On a solid set-screw collar, the set screw threads through the collar and presses against the shaft. The double split collar in this guide locks differently: its set screws clamp the split halves around the shaft. One listing uses socket cup-point set screws, which sit flush with the collar surface.

A double split collar clamps around the shaft instead of sliding on from the end. A solid collar is a ring that slides on from the end of the shaft.

How to Measure a Shaft for a Collar

Measure the shaft diameter before ordering: the bore of the collar must match it. The collars in this guide come in 1 in and 5/8 in bores.

The outside diameter decides whether the collar clears nearby parts, and the width decides how much room it takes along the shaft. The collars here run from 1-1/8 in to 1-3/4 in outside diameter, with widths of 1/2 in and 0.625 in.

Finally, note the set screw size so the matching hex wrench is on hand. The listings here use 1/4-28 and 5/16-18 screws, and one pack includes a hex wrench.

Shaft Collars for CNC Router Work

Once the shaft diameter is measured, the collars below cover the bores in this guide and handle the locating, spacing and stopping jobs around a CNC router.

Common Mistakes to Avoid

  • Wrong bore: measure the shaft diameter before ordering.
  • Wrong outside diameter: a collar whose outside diameter is too large for the space around the shaft will not fit.
  • Wrong set screw size: keep the matching hex wrench ready.
  • Expecting a load rating: none of the listings in this guide states one.

What Is a Shaft Collar: the Short Version

  1. A shaft collar is a ring that locks onto a shaft to hold parts in place.
  2. Solid set-screw collars tighten against the shaft; the double split collar clamps around it.
  3. Match the bore to the shaft diameter, then check outside diameter and width.
  4. Check the set screw size and keep the matching hex wrench ready.
  5. Use collars as stops, spacers, locators and bearing faces.

FAQ: lasers and CNC

What does a shaft collar do?

A shaft collar holds a part in place on a shaft and stops it from sliding. It works as a stop, a spacer or a locator.

What is the difference between a solid and a split shaft collar?

A solid collar slides onto the shaft from the end. A double split collar clamps around the shaft, which makes it easy to install.

Which bore size fits the shaft?

Measure the shaft diameter. The bore must match it: the collars in this guide come in 1 in and 5/8 in bores.

What is a shaft collar used for on a CNC router?

On a CNC router, a shaft collar locates parts, spaces components apart, stops wheels from drifting and serves as a bearing face.

Related: the CNC router machine guide, spoilboard setup guide and CNC router picks for sign making. Also see the CNC router bits for cutting wood guide.

More buying guides

CNC Routers ·

CNC Milling Machine Setup for Beginners

A beginner guide to CNC milling machine setup: square the vise, indicate the fixed jaw, set the work stop, clamp the part and check…