How to Use a Die Cutting Machine: A Step-by-Step Guide for Cards and Crafts
A step-by-step guide to using a die cutting machine: match the opening to your paper, build the plate sandwich, turn the crank and add foil for a finished card.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Manual Die Cutting and Embossing Machine9.6/10View on Amazon - 2
3'' Opening Mini Die Cutting and Embossing Machine9.5/10View on Amazon - 3
Mini Manual Die Cutting and Embossing Machine9.4/10View on Amazon - 4
We R Memory Keepers, Foil Quill Starter Kit9.3/10View on Amazon
Learning how to use a die cutting machine starts with a simple sandwich: paper, a die and two plates, fed through a manual crank press that cuts the shape or presses a raised pattern into the paper. This guide walks through each step in order, from picking a machine that fits your paper to adding foil with a starter kit, using the three manual machines below, plus a foil kit made for electronic cutting machines.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
We have not handled these machines in person, so this guide compares what each maker lists: opening size, the dies and plates in the box, and the materials each one states it cuts. Where a listing states nothing, we say so.

VEVOR Manual Die Cutting and Embossing Machine
A manual die cutting and embossing machine with a 9 inch opening, a crank, metal gears and a kit of cutting dies, embossing folders, paper sheets and cutting plates.
Pros
- 9 inch opening for paper sheets and cardstock
- Cutting dies, embossing folders, paper sheets and cutting plates in the box, so beginners can start right away
- Metal gears, ergonomic handle and non-slip base for smooth, steady cranking
- Folds for storage and unfolds ready to use in just 1 second
Cons
- 15.43 pounds, so it stays on the desk rather than travelling with you
- Paper and cardstock only; leather, fabric and foil need another machine
- No foil or heat transfer in the box; the Foil Quill kit below adds that step
- No warranty term is stated

3'' Opening Mini Die Cutting and Embossing Machine
A 3 inch opening mini die cutting and embossing machine with a 3.5 inch feed slot, a foldable design and a starter kit of embossing folders, dies with clear stamps and cardstock.
Pros
- Complete starter kit in the box: machine, 3 mini embossing folders, a set of dies with clear stamps and assorted cardstock
- Foldable design that fits a tote bag or backpack for classes and travel
- Clear sandwich guide: 1 pc 5 mm plate, paper, die and 3 mm plate for cutting; 2 pcs 3 mm plates and a folder for embossing
- Cuts 80-210gsm cardstock for cards, scrapbook layouts and home decor
Cons
- 3 inch opening limits it to small paper and small dies
- Cannot cut cloth, leather or plastic sheets, per the listing
- Cuts 80-210gsm cardstock only; heavier board is outside the stated range
- Complex dies may need an extra cardstock layer in the sandwich, per the maker

Mini Manual Die Cutting and Embossing Machine
A mini manual die cutting and embossing machine measuring 6.3 x 3.8 x 3 inch, with a built-in suction system and plates for dies, embossing folders, texture plates and contour steel rule dies.
Pros
- Cuts and embosses tissue paper, foils, acetate ribbon and thin leather
- Works with any dies, embossing folders, texture plates and contour steel rule dies
- Built-in suction system holds the machine steady while you crank
- Small 6.3 x 3.8 x 3 inch body that is easy to carry and does not take up space
Cons
- Mini size: the 6.3 x 3.8 x 3 inch body and 158 x 76 mm plates suit small dies only
- No dies, embossing folders or paper in the box, so the first project needs separate supplies
- Thin leather only; thicker leather and fabric are outside what the maker states
- No warranty term is stated

We R Memory Keepers, Foil Quill Starter Kit
A foil transfer starter kit with 3 pens, 4 adaptors, 3 foil rolls, 1 washi tape roll and 1 protective plate, made to fit most electronic cutting machines.
Pros
- Adds foil transfer to the cutting machine you already own
- 3 pens, 4 adaptors and 3 foil rolls in the box for varied foil projects
- Fits most electronic cutting machines, per the maker
- Protective plate and washi tape roll included for clean foil work
Cons
- Needs an electronic cutting machine; it cuts nothing on its own
- Not suitable for children under 3 years, per the maker
- Foil transfer only; it does not cut or emboss
- 3 foil rolls in the box, so refills are a separate purchase
Step 1: Match the opening to your paper
A die cutting machine cuts only what fits through its opening, so match the opening to the paper you already buy. The VEVOR here lists a 9 inch opening, the Find Scrapblooms lists a 3 inch opening with a 3.5 inch feed slot for 3 inch paper, and the BAOFALI lists a 6.3 by 3 inch plate that sets the size of paper it takes. Our manual die cutting machine guide covers how to choose between manual presses when you want more detail.
Step 2: Build the sandwich
Every cut on a manual crank press starts with a sandwich of plates, paper and die, in the order the maker gives. For die cutting, the Find Scrapblooms lists 1 pc 5 mm PC plate, paper, die cut and 3 mm PC plate; for embossing, it lists 2 pcs 3 mm PC plate with an embossing folder and paper inside. The BAOFALI says to place stencils and cardstock in the center of two plastic cutting mats, set the mat on the embossing table and turn the handle. Keep the die centered on the paper so the cut lands where you planned it.
Step 3: Turn the crank and lift the cut
With the sandwich built, feed it through the opening and turn the crank at a steady pace. The VEVOR uses a crank with metal gears, an ergonomic handle and a non-slip base, and the maker says the plates run smooth and steady. When the sandwich comes out the other side, lift the top plate and peel the paper away from the die to see the cut. If a complex die will not cut through, the Find Scrapblooms maker says to add a piece of cardstock to thicken the sandwich and run it through again.
Step 4: Emboss for a raised pattern
Embossing uses the same press with a folder instead of a die. The VEVOR is a 2-in-1 design, so the same crank delivers a clean cut or a rich embossed texture, and its box holds embossing folders with the cutting dies. The Find Scrapblooms box holds 3 mini embossing folders, and the best embossing machine for card making guide compares presses that focus on this step. Place the paper inside the folder, build the sandwich the maker lists, and crank it through the same way.
Step 5: Add foil with the Foil Quill
Foil gives a card a metallic finish, but it needs an electronic cutting machine, since the Foil Quill is a starter kit, not a press. Insert one of the Foil Quill tips into your electronic cutting machine, choose a design and let the machine do the work. The kit holds 3 pens, 4 adaptors, 3 foil rolls, 1 washi tape roll and 1 protective plate, and the maker says it fits most electronic cutting machines. Note that it fits electronic cutting machines, not the manual crank presses above. Keep the kit away from children under 3 years, as the maker states it is not suitable for them.
How to use a die cutting machine: the gear that does the work
The steps above need a crank press that fits your paper, plates that build the sandwich and dies that cut the shapes, so the picks below cover the cutting and embossing steps, plus a foil kit made for electronic cutting machines.
Common mistakes to avoid
- Buying a machine with an opening smaller than the paper you cut most.
- Feeding a bare die through the rollers without the plates the maker lists.
- Cutting leather, cloth or plastic sheets in a machine that lists cardstock only.
- Forgetting the embossing folder when you want a raised pattern instead of a cut.
- Expecting a foil kit to cut: the Foil Quill needs an electronic cutting machine to hold it.
How to use a die cutting machine: the short version
- Match the opening to your paper.
- Build the sandwich: plate, paper, die and plate.
- Turn the crank and lift the cut.
- Swap in an embossing folder for a raised pattern.
- Add foil with the Foil Quill kit when you want a metallic finish.
- Put the machine away when you finish.
FAQ: lasers and CNC
What size die cutting machine do I need for card making?
Match the opening to the paper you cut most. The VEVOR here lists a 9 inch opening, the Find Scrapblooms lists a 3 inch opening with a 3.5 inch feed slot for 3 inch paper, and the BAOFALI lists a 6.3 by 3 inch plate that sets the size of paper it takes. A wider opening takes larger cardstock, while a mini press suits small cards and travel.
Can a die cutting machine cut leather?
It depends on the machine. The BAOFALI lists thin leather among the materials it cuts and embosses, with tissue paper, foils and acetate ribbon. The Find Scrapblooms states it cuts 80-210gsm cardstock only and cannot cut cloth, leather or plastic sheets, and the VEVOR lists paper and cardstock only.
What is the difference between die cutting and embossing?
Die cutting cuts a shape out of paper with a metal die, while embossing presses a raised pattern into paper with a folder, without cutting through. The same crank machine does both: the VEVOR is a 2-in-1 design, and the Find Scrapblooms gives a different plate sandwich for each job, with 2 pcs 3 mm plates and a folder for embossing and 1 pc 5 mm plate, paper, die and 3 mm plate for cutting.
Do I need a cutting machine to use a Foil Quill?
Yes. The Foil Quill is a starter kit, not a machine: you insert one of its tips into your electronic cutting machine and choose a design, and the machine does the work. The kit holds 3 pens, 4 adaptors, 3 foil rolls, 1 washi tape roll and 1 protective plate, and the maker says it fits most electronic cutting machines.
What paper weight can the Find Scrapblooms mini machine cut?
The Find Scrapblooms here states 80-210gsm cardstock only. If a complex die will not cut through, the maker says to add a piece of cardstock to thicken the sandwich. Heavier board, cloth, leather and plastic sheets are outside what this machine states it cuts.
Related: the manual die cutting machine guide, best die cut machine for card making and best cutting machine for cardstock. Also see our best embossing machine for card making and the cutting machines category.




