How to Make a Sublimation Tumbler
A step-by-step guide to making a sublimation tumbler: print the design, wrap the blank, and heat it in a press or an oven.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
50 Pack Sublimation Tumblers Bulk9.6/10View on Amazon - 2
Hiipoo 8 Pack Sublimation Tumblers Blank 20 oz9.6/10View on Amazon - 3
YOUKE OLA 16 Pack Sublimation Tumblers Flat Edge9.6/10View on Amazon - 4
16 Pack Sublimation Tumblers Blanks Skinny9.5/10View on Amazon
A sublimation tumbler starts as a plain steel blank with a coated surface, and ends as a finished gift with a full-wrap design baked onto the coating. Learning how to make a sublimation tumbler means getting the moves right in order: print the design, wrap the blank tight, and heat it until the ink bonds with the coating. The steps below walk through the whole job, from the printed sheet to the finished tumbler, with the blanks that carry the work.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

50 Pack Sublimation Tumblers Bulk
A 50-pack of 20 oz straight stainless steel blanks with lids, straws, shrink wrap, paper and tape, with stated press and oven figures.
Pros
- 50-pack includes sublimation paper, tape, shrink wrap, straws and boxes
- States press and oven figures: 330 F for 50 seconds per side; 360 degrees F for 5-6 minutes
- 18/8 stainless steel, double-layer vacuum insulation; hot 9 hours, cold 12 hours
- Completely straight cup shape for a full-wrap print
Cons
- No warranty term is stated
- A 50-pack is more than a maker who needs a few blanks
- Only white is listed
- No weight is stated for the pack

Hiipoo 8 Pack Sublimation Tumblers Blank 20 oz
An 8-pack of 20 oz straight stainless steel blanks with lids, straws, paper and shrink wrap, with stated press and oven figures.
Pros
- States heat figures: 180-356°F, 50-100 seconds, oven 6 minutes
- Food-grade 18/8 stainless steel with a polymer sublimation coating
- Hot for up to 12 hours and cold for up to 12 hours
- 8-pack includes lids, straws, straw brushes, silicone bases, paper and shrink wrap
Cons
- No warranty term is stated
- Heat figures are a range, 180-356°F and 50-100 seconds, not one setting
- Only white is listed
- An 8-pack is small for a seller making large batches

YOUKE OLA 16 Pack Sublimation Tumblers Flat Edge
A 16-pack of 20 oz straight stainless steel blanks with a flat edge bottom, straws, shrink wrap and boxes.
Pros
- Flat edge bottom for a cleaner bottom edge and less ghost on a full image
- 304 stainless steel, double-walled
- 16-pack includes straws, shrink wrap sleeves and individual boxes
- Completely straight for a full-wrap print
Cons
- No heat figures are stated for a press or an oven
- No sublimation paper is listed in the box
- Only white is listed
- No straw brush or silicone base is listed in the box

16 Pack Sublimation Tumblers Blanks Skinny
A 16-pack of 20 oz straight stainless steel blanks with a removable handle, straws, lids, shrink wrap and boxes.
Pros
- Removable handle, with a box designed to hold the handle
- Completely straight for a full-wrap print
- 16-pack includes straws, lids, shrink wrap sleeves and individual boxes
- Stainless steel, double-walled
Cons
- No heat figures are stated for a press or an oven
- No sublimation paper is listed in the box
- Only white is listed
- The removable handle adds a fitting step before the tumbler is used
How to make a sublimation tumbler: print, wrap and heat
The design moves from paper to the coated blank under heat, with the wrap holding it tight. A straight blank makes the wrap easy. The four blanks below are all straight 20 oz blanks, so the steps fit each of them.
Step 1: Print the design on sublimation paper
Print the design on sublimation paper, sized to wrap the tumbler for a full-wrap print. The Maucircol pack includes sublimation paper, and the Hiipoo pack includes 10 sheets, so check what is in the box first. Trim the sheet so the edges meet, with the printed side against the blank.
Step 2: Wrap the blank and tape it tight
Set the printed sheet around the straight blank with the printed side down, and pull it tight. Tape the seam with high resistant tape; the Maucircol pack includes it. Slide a shrink wrap sleeve over the wrapped tumbler and smooth it down.
Step 3: Heat the tumbler in a press or an oven
Heat the wrapped tumbler in a heat press or a convection oven, following the figures the maker of your blank states. Maucircol states a heat press at 330 F for 50 seconds, rotated to the other side for another 50 seconds, or an oven at 360 degrees F for 5-6 minutes. Hiipoo states heating the heat press or oven to 180-356°F and pressing for 50-100 seconds, with an oven wait of 6 minutes. Cover the entire tumbler with sublimation paper to avoid uneven heating, as Hiipoo notes. For the choice between the two heat methods, see the oven versus press guide.
Step 4: Cool the tumbler and peel the wrap
Let the tumbler cool, then peel off the shrink wrap sleeve and the sublimation paper to show the finished design. Fit the lid and straw from the pack.
Pick the blank that fits the job
The blanks below carry the steps above: each blank is a straight 20 oz body for a full-wrap print, with straws, lids and shrink wrap in the pack.
FAQ: lasers and CNC
What do I need to make a sublimation tumbler?
You need a coated blank, sublimation paper, high resistant tape, a shrink wrap sleeve, and a press or an oven. The packs below include the blank with a lid and straw, plus shrink wrap; Maucircol also includes paper and tape, and Hiipoo includes paper.
Can I use an oven instead of a heat press for a sublimation tumbler?
Yes. Maucircol states an oven at 360 degrees F for 5-6 minutes, and Hiipoo states an oven wait of 6 minutes after heating to 180-356°F. For a press, Maucircol states 330 F for 50 seconds per side, and Hiipoo states 50-100 seconds.
What size tumbler blank should I buy?
The blanks below are all 20 oz straight skinny tumblers, and the straight shape suits a full wrap. Pick the pack size for how many tumblers you plan to make: Hiipoo holds 8, YOUKE OLA and TUMBCHIC hold 16 each, and Maucircol holds 50. For a size chart, see the sublimation tumbler size chart.
Do I need shrink wrap for a sublimation tumbler?
Hiipoo recommends using heat shrink wrap with the tumbler for the best results, and every pack below includes shrink wrap sleeves.
How do the packs in the gear section differ?
The blanks are all straight 20 oz stainless steel tumblers, so the packs differ in count and in what is inside the box. Hiipoo holds 8 with 10 sheets of paper; YOUKE OLA and TUMBCHIC hold 16 each; Maucircol holds 50 with paper and tape. TUMBCHIC adds a removable handle.
Related: the craft machines hub, heat presses and sublimation and best laser engraver for tumblers.




