How to Fix a Hot Glue Gun
How to fix a hot glue gun: run the heat-up, stick-size and feed checks in order, then pick a replacement from 3 guns and a 200-pack of sticks.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Gorilla Hot Glue Gun, Dual Temp, Mini Size9.7/10View on Amazon - 2
30W Fireproof Mini Hot Glue Gun with 30 Glue9.6/10View on Amazon - 3
Innovative Haus Mini Hot Glue Sticks for Mini Glue9.5/10View on Amazon - 4
Mr. Pen- Mini Hot Glue Gun with 40 Glue Sticks9.5/10View on Amazon
A sign is half-assembled on the bench, the next piece is ready to stick, and the glue gun gives a cold dribble instead of a clean bead: that is when how to fix a hot glue gun becomes the job in front of you. A cold nozzle, a wrong-size stick, a pulled stick or a tripped safety cutoff covers the failures this guide walks through. This guide walks through the checks in order, from the fastest fix to the point where a replacement gun makes more sense than a repair.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Gorilla Hot Glue Gun, Dual Temp, Mini Size
A dual-temp mini glue gun with a precision nozzle, a safety fuse and a built-in stand for DIY, craft and repair work.
Pros
- Dual temp: low heat for delicate materials, high heat for strong bonding
- Safety fuse shuts the gun off automatically in the event of a short
- Insulated nozzle, side fins and built-in stand
- 45 second working time with Gorilla weather resistant glue sticks
Cons
- Mini size for small jobs, not large glue-ups
- Dual temp means picking the right setting
- No warranty term is stated
- 45 second working time leaves little room to reposition a piece

30W Fireproof Mini Hot Glue Gun with 30 Glue
A 30W fireproof mini glue gun with 30 glue sticks, a 1 to 2 minute heat-up and overheat protection.
Pros
- Fast heat-up of 1 to 2 minutes with PTC ceramic heating
- Fireproof, heat-resistant material stated to work well under 300°C
- Overheat protection with a safety circuit and a drip-free nozzle
- 1.5m cord, stand base and rubber cap
Cons
- Mini size for small jobs, not large glue-ups
- Only 7mm sticks fit; other diameters will not work
- 1.5m cord limits how far the gun reaches from an outlet
- One heat setting for every material

Innovative Haus Mini Hot Glue Sticks for Mini Glue
A 200-pack of clear 4-inch mini glue sticks that set in 20 to 30 seconds for mini glue guns.
Pros
- 200-pack of clear 4-inch mini glue sticks
- Sets in 20 to 30 seconds for quick bonding
- Dual temp compatibility for low and high temperature mini guns
- Flexible sticks that will not break when bent
Cons
- Mini glue guns only; not compatible with regular sized glue guns
- Sticks only; no gun is included
- Short 4-inch sticks
- 200-pack suits frequent use more than occasional repairs

Mr. Pen- Mini Hot Glue Gun with 40 Glue Sticks
A mini glue gun with 40 glue sticks, an easy-squeeze trigger and a comfortable handle for craft, DIY and repair work.
Pros
- 40 glue sticks included with the gun
- Easy-squeeze trigger and comfortable handle for precise control
- Works on wood, metal, plastic and fabric
- Compact size, easy to store and transport
Cons
- No warranty term is stated
- Mini size for small jobs, not large glue-ups
- No wattage is stated
- One heat setting for every material
The quick answer
Start with heat: the kejector gun (on Amazon) below heats in 1 to 2 minutes. Next check the stick: mini guns take 7mm sticks. If the gun heats but nothing comes out, do not pull the stick: Gorilla states it should be fed through, not pulled out. If the gun has gone dead, the overheat circuit may have cut power, so let it cool and check the cord first. A blown safety fuse does not reset on cooling, so a gun that stays dead after cooling needs a replacement.
Step 1: Let it heat up
A gun that is still heating looks broken when it is only cold. The kejector gun states a heat-up of 1 to 2 minutes with PTC ceramic heating that keeps the temperature even. Wait for the full heat-up before judging the gun.
Step 2: Match the stick to the gun
Mini guns and full-size guns take different sticks, and the wrong size is a common cause of a jam. The kejector gun states sticks with a diameter of 7mm/0.28in, and the Innovative Haus sticks (on Amazon) state they fit mini glue guns only. The Innovative Haus sticks are 4 inches long and 0.27 inches across, and they set in 20 to 30 seconds.
Step 3: Feed the stick, do not pull it
A stick that is pulled backward can jam the feed. Gorilla states it plainly: do not pull glue sticks from the gun, and feed the remainder of a stick through instead. A nozzle that drips or blocks after that needs cleaning; see how to clean a hot glue gun nozzle and barrel for the steps.
Step 4: Check the safety cutoffs
Two guns below state safety cutoffs: the Gorilla gun (on Amazon) has a safety fuse that shuts the gun off in the event of a short, and the kejector gun has a safety circuit against overheating. Cooling resets the overheat circuit, not a blown fuse, so let a dead gun cool, check the cord, and try it again. If it stays dead after cooling, the fuse may have blown or the heater may have failed, and a replacement makes more sense than a repair.
The gear: glue guns and sticks for the fix
If the checks above point to a dead heater, a worn trigger or the wrong sticks, the 4 products below cover the replacement.
How to fix a hot glue gun: choosing a replacement
The stick decides the gun: mini guns take 7mm sticks, and the Innovative Haus 200-pack states it fits mini guns only. Dual temp matters when the work mixes delicate and heavy materials: the Gorilla gun runs low heat for floral, fabric, foam and jewelry and high heat for wood, plastic, metal and glass. See the temperature control comparison and the glue stick guide for the options.
FAQ: lasers and CNC
Why does my hot glue gun not heat up?
Give it the full heat-up time first: the kejector gun states 1 to 2 minutes. If it still stays cold, the overheat circuit may have cut power, so let it cool and try it again. A blown safety fuse does not reset on cooling, so a gun that stays dead after cooling needs a replacement.
What size glue sticks does a mini hot glue gun take?
Mini guns take 7mm sticks, and the kejector gun states sticks with a diameter of 7mm/0.28in. The Innovative Haus sticks are 4 inches long and 0.27 inches across, for mini guns only.
Can I pull a glue stick out of a hot glue gun?
No. Gorilla states that glue sticks should not be pulled from the gun, and that the remainder of a stick should be fed through instead. Pulling a stick backward can jam the feed.
What is the difference between low and high heat on a glue gun?
Low heat suits delicate materials and high heat suits strong bonding. The Gorilla gun states low heat for floral, fabric, foam and jewelry, and high heat for wood, plastic, metal and glass.
Related: the hot glue gun with temperature control, best glue sticks for hot glue gun, how to clean a hot glue gun and full-size hot glue gun vs mini.




