Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Clean Hot Glue Gun Nozzle and Barrel

A step-by-step guide to cleaning a hot glue gun nozzle and barrel, from wiping away drips to clearing a clog and swapping a worn nozzle.

How to Clean Hot Glue Gun Nozzle and Barrel
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Gorilla Mini Hot Glue Gun KitGorilla Mini Hot Glue Gun Kit9.7/10View on Amazon
  2. 2ROMECH 20W Mini Hot Glue Gun KitROMECH 20W Mini Hot Glue Gun Kit9.6/10View on Amazon
  3. 3Krightlink Mini Hot Glue Gun Kit with 30 Glue Sticks 20w FastKrightlink Mini Hot Glue Gun Kit with 30 Glue Sticks 20w Fast9.6/10View on Amazon

How to clean hot glue gun nozzles and barrels comes down to a cool, unplugged gun and a simple routine: wipe away drips and strings while the nozzle is still warm, clear the nozzle opening with a fine wire when glue stops flowing smoothly, and swap the nozzle when cleaning no longer restores a clean bead. A dirty nozzle can cause strings and uneven lines, so a short cleaning routine after messy jobs keeps the gun ready for the next craft session. The steps below cover the nozzle, the barrel and the nozzle swap.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

How to Clean Hot Glue Gun Nozzles

Unplug the gun and let it cool until the nozzle is warm rather than hot. Wipe the outside of the nozzle with a dry cloth to lift drips and strings, and pick off cooled beads with a wooden stick or a plastic scraper that will not scratch the metal. The MONVICT gun (on Amazon) keeps working for about 5 minutes after the cord is unplugged, so the nozzle stays hot for a while after the cord is out.

When glue stops flowing smoothly, clear the opening with a fine cleaning wire. The ECuoPix torch tip cleaner kit includes cleaning wires in diameters from 0.4 mm to 1.6 mm, plus a flat file for the nozzle face. Pick a wire that slides into the opening without force and push it through gently; a wire that is too large will not enter, and a wire that is too small will not clear the clog. For heat settings while you warm the gun again, see the hot glue gun temperature guide.

Check the nozzle face for a ring of dried glue and brush it away with a soft brush. The ECuoPix kit includes 5 brushes from 3 mm to 7 mm with nylon fibers for narrow spaces. A brush reaches the rim and the threads where a cloth cannot reach.

Clean the Barrel and Feed Path

Glue left in the barrel hardens between jobs and melts again when the gun warms up, so a leftover stick is normal. If the bead runs unevenly, push a fresh stick in and let the gun reach working temperature before judging the flow, then wipe the feed opening with a dry cloth. Stick sizes vary by gun, so check the size your gun takes in the hot glue stick sizes guide. The MONVICT kit includes 12 glue sticks that measure 5.9 inches long with a diameter of 0.43 inches.

Brush the feed opening and the area around the trigger with a soft brush to move dust and dried flakes out of the path. The MONVICT gun runs at 120W on high and 80W on low, with low at 284℉ for thin materials and high at 482℉ for stronger bonds on wood, plastic and metal. Use the low setting for thin, fragile materials such as fabric, paper and foam.

Swap a Nozzle When Cleaning Is Not Enough

A nozzle that stays clogged after cleaning has reached the end of its service. Unplug the gun, let it cool, and unscrew the nozzle with the wrench that came with the nozzle set. The MONVICT gun ships with 7 copper nozzles and a wrench for nozzle changes, and the Surebonder 4-pack includes (on Amazon) an adapter and 3 aluminum nozzles in small round, large round and flat shapes, with a check valve that blocks glue from flowing back into the gun.

Match the thread before buying a spare set. The QWORK 4-piece copper nozzle set uses a 10.8 mm thread, given as 7/16 inch, and the maker states it fits more than 90% of glue guns. The set holds nozzles that measure 2.0 by 34 mm, 2.0 by 50 mm, 3.0 by 50 mm and 2.0 by 70 mm. The 6-piece copper set holds 2 flat nozzles for wide glue lines, a wrench and 3 rubber O-rings that seal the nozzle seat. Fit the O-ring, thread the nozzle on by hand, then snug it with the wrench. Nozzle sizes vary by gun, so see the full size hot glue gun vs mini guide before ordering spares.

Pick the Right Cleaning Wires and Brushes

Fine wires and small brushes do most of the work on a clogged nozzle. The ECuoPix kit holds cleaning wires from 0.4 mm to 1.6 mm, 5 brushes from 3 mm to 7 mm and a flat file in an aluminum box. The Petutu 4-set (on Amazon) holds 26 wires, 20 needles and 10 brushes, with wire diameters from 0.3 mm to 1.5 mm and brush diameters of 2 mm, 3 mm, 4 mm, 5 mm and 7 mm.

For very fine openings, the Mozeat 60-piece kit holds needles from 0.15 mm to 0.4 mm in 6 bottles with 10 needles in each bottle, and the YOUYIDUN 48-piece kit holds 38 needles from 0.15 mm to 0.8 mm with tweezers and copper wire brushes. Pick the smallest wire that clears the clog, and keep the kit in its case so the fine wires stay straight.

Keep the Gun Clean Between Jobs

Wipe the nozzle while it is still warm after each session, before the drips harden into a crust. Stand the gun on its rest with the nozzle pointing down, and store it where the cord and the nozzle stay clear of dust. The MONVICT kit includes 3 silicone finger covers for handling warm parts, which help when wiping a nozzle that is still warm.

Watch for a bead that wanders, strings that follow the nozzle, or drips between squeezes. The QWORK nozzles carry a steel ball that blocks drips, and the Surebonder nozzles carry a check valve that blocks backflow, so a gun that still drips with a fresh nozzle needs a look at the heat setting, not another nozzle. For wood projects, see the does a hot glue gun work on wood guide.

How to Clean Hot Glue Gun: The Short Version

  1. Unplug the gun and let the nozzle cool until it is warm rather than hot.
  2. Wipe drips and strings from the nozzle with a dry cloth.
  3. Push a fine wire through the nozzle opening to clear a clog, then wipe again.
  4. Brush the nozzle face, the threads and the feed opening.
  5. Push a fresh stick in if the bead runs unevenly, and let the gun reach working temperature first.
  6. Swap the nozzle with a wrench when cleaning no longer restores a clean bead.

FAQ: lasers and CNC

Can I clean a hot glue gun while it is still plugged in?

No. Unplug the gun and switch it off before cleaning, and let the nozzle cool until it is warm rather than hot. A plugged-in gun can melt glue onto the cloth and burn fingers on the nozzle.

What size cleaning wire fits a glue gun nozzle?

Pick a wire that slides into the opening without force. The ECuoPix kit holds wires from 0.4 mm to 1.6 mm, and needle kits from 0.15 mm to 0.4 mm suit very fine openings. Start with the smallest wire that clears the clog.

How do I remove a nozzle that will not turn?

Unplug the gun and let it cool, then grip the nozzle with the wrench from the nozzle set and turn it slowly. The Surebonder nozzles come off with an adjustable wrench, and the MONVICT kit includes a wrench for nozzle changes. If it still will not turn, do not force it; let the gun cool fully before trying again.

Why does a hot glue gun keep dripping?

Drips come from glue left in a hot nozzle and from a worn nozzle valve. Wipe the nozzle after each session, and fit a nozzle with a steel ball or a check valve: the QWORK nozzles carry a steel ball that blocks drips, and the Surebonder nozzles carry a check valve that blocks backflow. If a fresh valve still drips, the cause sits beyond the nozzle, so check the heat setting before swapping parts again.

How often should I clean a hot glue gun?

Clean the nozzle after each messy session and whenever the bead turns uneven or strings follow the nozzle. A gun that feeds a clean bead needs only a quick wipe after use. Deep cleaning with wires and brushes is for clogs and heavy buildup, not for every session.

Related: the craft machines hub, full size hot glue gun vs mini and hot glue stick sizes. Also see the hot glue gun temperature guide. Also see the does a hot glue gun work on wood guide.

More buying guides

Craft Machines ·

How to Fix a Hot Glue Gun

How to fix a hot glue gun: run the heat-up, stick-size and feed checks in order, then pick a replacement from 3 guns and…