How Long Is 1kg of PLA Filament?
A 1kg spool of 1.75mm PLA filament is sold by weight, not length, so compare the weight, diameter, and colors before ordering.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
SUNLU 3D Printer Filament Bundle, 10KG, 1kg Spool9.6/10View on Amazon - 2
SUNLU 4KG Quadruple Color Silk Filament9.6/10View on Amazon - 3
Meuymeu 10KG PLA+ Filament Bundle9.6/10View on Amazon - 4
3DHoJor Basic PLA 3D Printer Filament Bundle,10KG9.6/10View on Amazon
How long is 1kg of PLA filament? The short answer is that the listings in this guide do not give a length in meters: they sell filament by weight, and the length of a spool is set by its diameter and material, so it is not a single fixed figure. A spool can hold a different length from another spool of the same weight when the diameter differs, which is why the listings state weight and diameter instead of length.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

SUNLU 3D Printer Filament Bundle, 10KG, 1kg Spool
A 10-roll bundle of 1kg spools of 1.75mm PLA+ in 10 colors, accurate to +/- 0.02mm.
Pros
- 10 rolls of 1kg 1.75mm PLA+ filament in 10 colors
- Dimensional accuracy of +/- 0.02mm
- 8.00-inch spool diameter, 2.50-inch width, 2.20-inch hub hole
- Neatly wound spools for steady feeding
Cons
- No warranty term is stated
- 10 rolls to store when you need only a few colors
- Nozzle temperature of 210°C to 235°C, above the range of some PLA filaments
- The bundle weighs 22.05 lb, so moving the full bundle takes effort

SUNLU 4KG Quadruple Color Silk Filament
A 4-roll bundle of 1kg spools of 1.75mm four-color silk PLA+, accurate to +/- 0.02mm.
Pros
- One filament shows four colors as it rotates
- Silk texture with a smooth, glossy surface
- Dimensional accuracy of +/- 0.02mm
- 200mm spool diameter, 67mm width, 55mm hub hole
Cons
- No warranty term is stated
- 4 rolls only, against 10-roll bundles here
- The silk finish is aimed at arts and crafts
- A glossier finish needs higher temperatures and lower speeds

Meuymeu 10KG PLA+ Filament Bundle
A 10-roll bundle of 1kg spools of 1.75mm PLA+ in 10 colors, accurate to ±0.03mm.
Pros
- 10 rolls of 1kg 1.75mm PLA+ filament in 10 colors
- ±0.03mm accuracy with neatly wound spools
- Nozzle temperature of 200°C-220°C and print speed of 0-300mm/s
- Standard 1.75mm diameter for most FDM 3D printers
Cons
- 10 rolls to store when you need only a few colors
- Accuracy of ±0.03mm, wider than the ±0.02mm of the SUNLU spools
- Opened spools need a sealed container, per the listing
- Recommended settings are starting points that need adjusting to your printer

3DHoJor Basic PLA 3D Printer Filament Bundle,10KG
A 10-roll bundle of 1kg spools of 1.75mm basic PLA in 10 colors, accurate to +/- 0.03mm.
Pros
- 10 rolls of 1kg 1.75mm PLA filament in 10 colors
- Dimensional accuracy of +/- 0.03mm
- Printing temperature of 190-230℃ with a recommended temperature of 215℃
- 40-300mm/s print speed with a 100% fan speed
Cons
- 10 rolls to store when you need only a few colors
- Accuracy of +/- 0.03mm, wider than the +/- 0.02mm of the SUNLU spools
- Basic PLA, without the silk finish or PLA+ claims of the other bundles
- Aimed at print farms and schools, so it suits high-volume printing
How long is 1kg of PLA filament?
Filament is sold by weight: a 1kg spool holds 1kg of PLA. The length that weight makes depends on the diameter: thinner filament packs more length into the same weight. The spools in this guide are all 1.75mm filament, so they share a diameter. Check the diameter before ordering, since a spool in a different diameter is a different length for the same weight.
What sets the length of a spool
Weight, diameter, and material set how much length a spool holds. The listings here state the weight per spool and the diameter, and the material is PLA or PLA+. A bundle of 10 spools of 1kg holds 10kg in total, and a bundle of 4 holds 4kg. Spool size also matters for fit: the SUNLU PLA+ spool measures 8.00 inches across and 2.50 inches wide, with a hub hole of 2.20 inches, while the SUNLU silk spool measures 200mm across and 67mm wide, with a hub hole of 55mm.
1kg PLA spools for your printer
Each spool below holds 1kg of 1.75mm PLA filament, so color, material, and bundle size are the main differences.
How to pick a 1kg spool
Start with the diameter your printer takes: the spools here are 1.75mm, which fits almost all 1.75mm FDM printers. Then pick colors and bundle size: the SUNLU PLA+, Meuymeu, and 3DHoJor bundles each hold 10 spools of 1kg in 10 colors, and the SUNLU silk bundle holds 4 spools of 1kg in a single four-color filament. Check the nozzle and bed temperatures before ordering.
FAQ: lasers and CNC
How much filament is on a spool?
The spools here hold 1kg each. The bundles hold 10kg across 10 spools, except the SUNLU silk bundle, which holds 4kg across 4 spools.
How long is a spool of filament?
The listings do not state a length. Length is set by weight, diameter, and material, so a 1kg spool of 1.75mm PLA holds a different length from a spool in another diameter.
Does 1kg of PLA fit any 3D printer?
It fits printers that take 1.75mm filament. The SUNLU spools suit almost all 1.75mm FDM printers, the Meuymeu filament (on Amazon) is made for most FDM printers that support 1.75mm material, and the 3DHoJor filament (on Amazon) lists Bambu Lab, AnkerMake, Voron, Raise3D, Prusa, and Creality Ender printers.
What temperatures does PLA print at?
It varies by filament. The SUNLU PLA+ lists 210°C to 235°C at the nozzle and 55°C to 65°C at the bed, the SUNLU silk lists 205-235°C and 50-60°C, the Meuymeu lists 200°C-220°C and 0°C-60°C, and the 3DHoJor lists 190-230℃ with a recommended 215℃ and a bed of 45-60°C.
How should I store PLA filament?
Keep it dry and sealed when you are not printing. The SUNLU silk filament comes in airtight vacuum packaging, the 3DHoJor bundle comes in a sealed vacuum bag with a desiccant bag, and the Meuymeu listing advises a sealed container for opened filament, dried before printing after long storage.
Related: the 3D printer hub, how to remove filament from a 3D printer, and 3D printer first layer problems and fixes.




