Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Deep Cut vs Fine Point Blade: Which One Should You Buy?

Three cutting blades compared on angle and depth: deep cut blades for thick materials and fine point blades for thin media.

Deep Cut vs Fine Point Blade: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1THANMAO 40 Pcs Replacement Blades CompatibleTHANMAO 40 Pcs Replacement Blades Compatible9.6/10View on Amazon
  2. 2Cricut Deep - Point Blade + HousingCricut Deep - Point Blade + Housing9.5/10View on Amazon
  3. 3Cricut Deep Cut Blade, (2 Counts)Cricut Deep Cut Blade, (2 Counts)9.2/10View on Amazon

Cutting thick chipboard for a wall calendar calls for a different edge than slicing thin rice paper for a delicate overlay. The deep cut vs fine point blade choice comes down to angle and material: in these listings, the steeper 60-degree edge is the deep cut edge for thick stock, and the 30-degree edge is the fine point edge for thin media. This comparison uses three listings to show where each side fits and where the listing leaves it unclear.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Verdict: pick the deep cut side for thick materials like chipboard, foam sheets and cardboard, and the fine point side for thin media like rice paper and film. The THANMAO set covers both sides in a single set; the Cricut deep-point blade with housing is the single-blade deep cut pick.

Machines on the list

THANMAO 40 Pcs Replacement Blades Compatible

THANMAO 40 Pcs Replacement Blades Compatible

THANMAO9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 40-piece set with fine point, standard and deep cut blades for thin, standard and deep media; for a maker wanting every angle in one set, skip it if only Cricut-brand blades will do.

Pros

  • Three angles in one set: 30, 45 and 60 degrees
  • 40 pieces, with 10 fine point, 20 standard and 10 deep cut blades
  • Rubber covers over the sharp heads to prevent finger injury
  • 1 Year warranty stated on the listing

Cons

  • Fine point blades are only 10 of the 40 pieces
  • Depth must be adjusted by hand for different materials
  • No housing is mentioned in the listing
  • No cut depth in millimeters is stated
Cricut Deep - Point Blade + Housing

Cricut Deep - Point Blade + Housing

Cricut9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A deep-point blade with housing for thick materials up to 1.5mm, for a maker cutting chipboard, foam sheets and cardboard; skip it for thin media work.

Pros

  • 60-degree angle, steeper than the stated 45-degree standard
  • Cuts 50+ materials up to 1.5mm
  • Carbide steel blade with housing included
  • Stated compatibility with Cricut Maker and Explore machines

Cons

  • No warranty term is stated on the listing
  • Single item, not a multi-blade set
  • Works only with the stated Cricut Maker and Explore machines
  • No thin-media use is stated for this blade
Cricut Deep Cut Blade, (2 Counts)

Cricut Deep Cut Blade, (2 Counts)

Cricut9.2/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A Cricut deep cut blade with stated dimensions but no stated materials or cut depth; for a buyer who wants the Cricut name and checks the count before buying.

Pros

  • Title identifies it as a deep cut blade
  • Title states 2 counts, a spare if the count holds
  • Product and package dimensions are stated
  • Cricut brand name on the listing

Cons

  • No materials, angle or cut depth are stated
  • No machine compatibility is stated
  • No warranty term is stated on the listing

Other machines to compare

Side by side

Blade HQ Score Angle Notes
THANMAO 40 Blades 9.6/10 30, 45 and 60 degrees 40-piece set across three angles
Cricut Deep-Point Blade 9.5/10 60 degrees Blade plus housing included
Cricut Deep Cut Blade 9.2/10 Not stated Title says 2 counts, spec table says 1

Specs are what each manufacturer publishes as its rating on the listing, collected 4 November 2026.

Deep Cut vs Fine Point Blade: Angle and Depth

The Cricut deep-point listing states a 60-degree angle against a 45-degree standard angle, and the THANMAO listing gives three: 30 degrees for fine point, 45 degrees for standard, and 60 degrees for deep cut. The contrast holds for the two named sides: 60 degrees for deep work and 30 degrees for fine work; the 45-degree blade is the standard blade, not a middle depth. Cut depth is less clear. Only the Cricut deep-point listing states a depth, up to 1.5mm. Neither other listing states one, so depth cannot decide this comparison, and the 1.5mm figure describes the Cricut deep-point listing only.

Materials

The deep cut side names thick stock. The Cricut deep-point listing states chipboard, rubber sheets, thick cardstock, stiffened felt, foam sheets and cardboard, and names wall calendars, stamps and magnets. The THANMAO 60-degree blades suit fabric, cork, magnet, leather and thick card stock. On the fine point side, THANMAO 30-degree blades suit window tint, film and rice paper. The set’s 45-degree blades are the standard blades, suiting paper, vinyl, sticker and adhesive foil. The Cricut Deep Cut Blade listing names no materials at all.

Compatibility

The Cricut deep-point blade with housing is stated compatible with Cricut Maker and Cricut Explore machines, including Explore, Explore One, Explore Air and Explore Air 2. The THANMAO set is stated compatible with Explore Air 2, Air 3, Explore 4, Maker, Maker 3, Maker 4 and Expression. The Cricut Deep Cut Blade listing states no compatibility, so confirm fit before buying.

What Is in the Box

The Cricut deep-point purchase is one blade with housing, with a stated count of 1. The THANMAO purchase is 40 pieces: 10 fine point, 20 standard and 10 deep cut blades, each sharp head wrapped in a rubber cover. The Cricut Deep Cut Blade listing disagrees with itself: the title says 2 counts while the spec table lists 1 item. The title takes precedence, but the mismatch is worth checking before buying.

Safety and Handling

These are sharp cutting edges, and the THANMAO listing names finger injury as the risk its rubber covers prevent. The THANMAO listing wraps each sharp head in a rubber cover to prevent finger injury, and directs the user to pull the cover off during use and adjust depth by hand for different materials. The Cricut listings state no handling guidance. Keep the THANMAO set’s rubber covers on until use and store blades out of reach.

Choose Deep Cut If

  • You cut chipboard, foam sheets or cardboard.
  • You want a blade plus housing in a single Cricut purchase.
  • You cut fabric, cork, magnet, leather or thick card stock.

Choose Fine Point If

  • You cut thin media like rice paper, film or window tint.
  • You want fine point, standard and deep cut blades in a single set.
  • You want spares on hand.
Safety

Blades are sharp. Keep the THANMAO set’s rubber covers on until use and store blades out of reach.

Project Match

  • Wall calendars, stamps and magnets: the Cricut deep-point blade.
  • Window tint, film and rice paper: THANMAO 30-degree blades.
  • Thick card stock: THANMAO 60-degree blades or the Cricut deep-point blade.
  • Fabric, cork, magnet and leather: THANMAO 60-degree blades.
  • Everyday paper, vinyl, sticker and adhesive foil work: the THANMAO 45-degree standard blades.

FAQ: lasers and CNC

What is the difference between a deep cut blade and a fine point blade?

Angle and material. In these listings, the deep cut edge is 60 degrees for thick materials, and the fine point edge is 30 degrees for thin media.

Can one set cover both thick and thin materials?

The THANMAO set can: it holds 10 fine point blades for thin media and 10 deep cut blades for deep media, plus 20 standard blades.

Do these blades fit Cricut Maker and Explore machines?

The Cricut deep-point listing states Maker and Explore machines, and the THANMAO listing states Explore Air 2, Air 3, Explore 4, Maker, Maker 3, Maker 4 and Expression. The Cricut Deep Cut Blade listing states no compatibility.

How many blades are in the Cricut Deep Cut Blade listing?

The title says 2 counts and the spec table lists 1 item. The title takes precedence, but check the count before buying.

Do the blades need depth adjustment?

The THANMAO listing states depth must be adjusted by hand for different materials. The Cricut listings state no depth adjustment.

Related: Cricut Explore vs Cricut Maker, best cutting machine for cardstock, cutting machines and best craft machines for stickers.

More buying guides