Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Soldering Vise (2026)

Four soldering vises for bench work, from a vacuum-base vise with a 360-degree swivel head to a flat PCB holder.

Best Soldering Vise (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1POWERTEC Vacuum ViseBest OverallPOWERTEC Vacuum Vise9.6/10View on Amazon
  2. 2Fasmov Table ViseBest Steel JawsFasmov Table Vise9.5/10View on Amazon
  3. 3Stickvise PCB ViseBest for PCBsStickvise PCB Vise9.5/10View on Amazon
  4. 4Generic Mini Vise ClampBest CompactGeneric Mini Vise Clamp9.4/10View on Amazon

A soldering vise holds the work still while both hands stay free for the iron and the solder. A board that shifts mid-joint makes a poor joint, and a small part that rolls off the bench ends the session early. The best soldering vise grips the work without marring it, stays put on the bench, and turns to meet the iron. These 4 picks cover a vacuum suction base, a table clamp, and a flat PCB holder, compared by jaw, opening, base, and weight.

LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.

Quick picks

  • Best Overall POWERTEC Vacuum Vise: A 2-3/4 inch jaw, a 360-degree swivel head with a 90-degree tilt, and removable rubber jaw caps on a vacuum suction base. Check price on Amazon
  • Best Steel Jaws Fasmov Table Vise: 3 by 3/4 inch jaws of hardened high-carbon steel alloy with a 2 inch opening, at 1.9 lb. Check price on Amazon
  • Best for PCBs Stickvise PCB Vise: A low profile holder with nylon jaws that keeps a circuit board flat for soldering at table level. Check price on Amazon
  • Best Compact Generic Mini Vise Clamp: A small aluminum vise with a 360-degree swivel suction base for light-duty precision tasks. Check price on Amazon

Machines on the list

POWERTEC Vacuum Base Vise

POWERTEC Vacuum Base Vise

POWERTEC9.6/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A die cast aluminum suction vise with a 2-3/4 inch jaw, a 360-degree swivel head, and removable rubber jaw caps for bench work.

Pros

  • 2-3/4 inch jaw with a V-groove for round or irregular shapes
  • 360-degree swivel head with a 90-degree tilt
  • Rubber suction base with a locking lever for a firm hold
  • Removable rubber jaw caps protect delicate workpieces

Cons

  • No warranty term in the listing
  • Suction base needs a smooth, non-porous surface
  • Holds items up to 65 mm wide, so larger work needs a bigger vise
  • At 3.09 lb it weighs more than the Fasmov at 1.9 lb and the Stickvise at 0.33 lb
Fasmov Swivel 3" Universal Table Vise Tilts Rotate

Fasmov Swivel 3" Universal Table Vise Tilts Rotate

Fasmov9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A cast aluminum table vise with 3 inch jaws of hardened high-carbon steel alloy and a 2 inch opening for small parts.

Pros

  • 3 x 3/4 inch jaws of hardened high-carbon steel alloy
  • 2 inch opening for workbench and table clamping
  • Rotates to any angle with rubber jaws for a firm grip
  • Lightweight at 1.9 lb for a portable bench vise

Cons

  • No warranty term in the listing
  • No suction base, so it needs a bench edge to clip to
  • No stated jaw cap material beyond rubber
  • Suits small parts; the 2 inch opening limits larger work
Stickvise PCB Vise with Standard Nylon Jaws Grey

Stickvise PCB Vise with Standard Nylon Jaws Grey

Stickvise9.5/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A low profile PCB holder with standard nylon jaws that holds a circuit board flat for soldering at table level.

Pros

  • Holds a circuit board flat for soldering at table level
  • Standard nylon jaws in grey
  • Weighs 0.33 lb, the lowest stated weight in this guide
  • Extra jaw sets and a PartLift accessory are named for special jobs

Cons

  • No warranty term in the listing
  • Made for circuit boards, not for round or heavy work
  • Nylon jaws suit PCBs, not metal parts that need a steel grip
  • At 7.87 inches long it takes more bench length than the mini vises
Mini Vise Clamp, Small Table Top Bench Vise

Mini Vise Clamp, Small Table Top Bench Vise

Generic9.4/10 HQ Score
i
The HQ Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A compact aluminum mini vise clamp with a 360-degree swivel suction base for light-duty precision tasks.

Pros

  • 360-degree swivel base adjusts the working angle quickly
  • Suction base repositions easily on clean, smooth surfaces
  • Compact format fits desks, counters, and hobby stations
  • Aluminum body with a simple screw adjustment

Cons

  • No warranty term in the listing
  • Built for small-item holding rather than high-force jobs
  • Suction base works best on clean, smooth surfaces
  • A small vise, so it does not replace a full-size bench vise

Specs compared

Model HQ Score Jaw Opening Base Swivel Weight Jaw protection
POWERTEC Vacuum Vise 9.6/10 2-3/4 in Up to 65 mm (2-9/16 in) Vacuum suction, locking lever 360 deg, 90 deg tilt 3.09 lb Removable rubber caps
Fasmov Table Vise 9.5/10 3 x 3/4 in (79 x 17 mm) 2 in (51 mm) Table clamp Rotates to any angle 1.9 lb Rubber, removable
Stickvise PCB Vise 9.5/10 Nylon jaws Not stated Flat, table level Not stated 0.33 lb Nylon jaws
Generic Mini Vise Clamp 9.4/10 Not stated Not stated Suction, 360 deg swivel 360 deg Not stated Not stated

Size and performance figures are the brand’s ratings quoted from listings on 21 November 2026. Jaw is the width of the jaw as listed; opening is the widest item the vise takes.

What the listings tell you, and what they leave out

4 listings were read for this guide. None states a warranty term, so every warranty score is 0 and every warranty reads Not stated. 3 of the 4 state a weight: the POWERTEC at 3.09 lb, the Fasmov at 1.9 lb, and the Stickvise at 0.33 lb. The Generic mini vise states no weight and no jaw size.

Jaw size is stated for the POWERTEC at 2-3/4 inches and for the Fasmov at 3 by 3/4 inches. The Stickvise names nylon jaws without a size, and the Generic mini vise names no jaw size at all. The Stickvise listing also names extra jaw sets and a PartLift accessory. The Generic listing gives 2 sizes for the same vise.

Buying guide: choosing the best soldering vise

Jaw size and opening

Start with the jaw, since it sets what the vise can hold. The POWERTEC jaw measures 2-3/4 inches and takes items up to 65 mm wide, with a V-groove for round or irregular shapes. The Fasmov jaw measures 3 by 3/4 inches with a 2 inch opening. The Stickvise uses standard nylon jaws for a circuit board, with no opening figure stated. The Generic mini vise states no jaw size, so its fit for a part is a guess until the vise arrives.

Base and positioning

The base decides whether the vise stays put. The POWERTEC uses a rubber suction base with a locking lever on smooth, non-porous surfaces such as glass, granite, steel, laminate, or marble. The Generic mini vise uses a suction base too, best on clean, smooth surfaces, with a 360-degree swivel. The Fasmov clips to a workbench or table. The Stickvise sits flat at table level and holds the board still.

Weight and portability

Weight matters when the vise moves between benches. The Stickvise weighs 0.33 lb and measures 7.87 by 3.0 by 0.75 inches, so it rides along in a tool bag. The Fasmov weighs 1.9 lb. The POWERTEC weighs 3.09 lb, the most of the 3 stated weights, and its suction base needs a flat surface at each stop. The Generic mini vise states no weight.

Jaw caps and delicate work

Bare metal jaws mark soft parts, so caps matter for delicate work. The POWERTEC ships with removable rubber jaw caps that protect workpieces from scratches. The Fasmov has rubber jaws that come off to reveal a cross pattern for wire and rods. The Stickvise uses nylon jaws, which suit a circuit board. The Generic mini vise states no jaw caps.

Project Match

  • Circuit board soldering: Stickvise PCB Vise, which holds the board flat at table level with nylon jaws.
  • Jewelry, watch repair, and small parts: Generic Mini Vise Clamp, a light-duty vise with a 360-degree swivel suction base.
  • Model building, crafts, and light woodworking: POWERTEC Vacuum Vise, with a suction base, a 90-degree tilt, and a V-groove jaw.
  • Drilling and woodworking on small parts: Fasmov Table Vise, with steel jaws and a table clamp.
  • Heavy shop work: Not stated for any pick; all 4 are hobby or light-duty vises.

How the scores add up

Each vise is scored on performance, build, value, safety and warranty. How we pick explains the weights. A spec the listing does not publish scores nothing.

Product HQ Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
POWERTEC Vacuum Vise 9.6 30 21 20 5 0
Fasmov Table Vise 9.5 29 21 20 4 0
Stickvise PCB Vise 9.5 28 20 20 3 0
Generic Mini Vise Clamp 9.4 26 19 19 3 0

We translate weighted points into a score with 9.2 as its floor and 9.8 as its cap; the straight-line conversion keeps the ranking exactly.

FAQ: lasers and CNC

What size soldering vise holds a circuit board?

The Stickvise holds a circuit board flat and measures 7.87 by 3.0 by 0.75 inches, with standard nylon jaws. It sits at table level, so the board stays still while both hands work the iron and the solder.

Does a suction base vise stay put on a smooth bench?

The POWERTEC uses a rubber suction base with a locking lever on smooth, non-porous surfaces such as glass, granite, steel, laminate, or marble. The Generic mini vise uses a suction base best on clean, smooth surfaces.

Which soldering vise has rubber jaw caps?

The POWERTEC ships with removable rubber jaw caps that protect delicate workpieces from scratches. The Fasmov has rubber jaws that come off to reveal a cross pattern for wire and rods.

Can a soldering vise hold round parts?

The POWERTEC V-groove jaw grips round or irregular shapes up to 65 mm wide. The Fasmov cross pattern under its rubber jaws suits wire and rods.

Related: the electronics making hub, the soldering hub, and the best soldering iron for PCB work, best soldering mat, and best soldering station for hobbyists.

More buying guides