Nema 17 vs Nema 23 CNC: Which One Should You Buy?
Two STEPPERONLINE stepper motors compared on holding torque, body size, step angle, current and shaft, with one Nema 17 and one Nema 23 example.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
STEPPERONLINE CNC Stepper Motor Nema 23 Bipolar9.5/10View on Amazon - 2
STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A9.4/10View on Amazon
A sign blank that needs fine detail work and a router table that needs to push a heavy gantry ask for different motors, and that is the heart of the nema 17 vs nema 23 cnc choice. This comparison puts one STEPPERONLINE example of each size side by side, using only what each listing states, and goes through holding torque, body size, step angle, current and shaft size so you can match the motor to the machine.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: pick the Nema 23 example if your machine needs more holding torque for a heavier gantry or a spindle, with a 1.9Nm figure against the Nema 17 example at 59Ncm. Pick the Nema 17 example for a compact desktop build, where its 1.65 x 1.65 x 1.89 in body and 2.0A rated current suit a smaller frame and driver.
Machines on the list

STEPPERONLINE CNC Stepper Motor Nema 23 Bipolar
A Nema 23 bipolar stepper motor rated 2.8A with 1.9Nm holding torque, a 6.35mm single shaft and a 1.8 deg step angle for CNC mill, lathe and router use.
Pros
- 1.9Nm (269oz.in) holding torque
- Single shaft, 6.35mm diameter
- 1.8 deg step angle, 200 steps per revolution
- 4-wire bipolar build for CNC mill, lathe and router
Cons
- No warranty term is stated
- No cable is listed in the box
- No shaft length is stated
- 2.8A rated current needs a driver rated for that current

STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A
A Nema 17 bipolar stepper motor rated 2.0A with 59Ncm holding torque, a 1.65 x 1.65 x 1.89 in body and a 1m cable with connector for 3D printer and CNC use.
Pros
- 59Ncm holding torque in a compact body
- 1m cable with 0.1 in pitch connector included
- 4-wire bipolar build for 3D printer and CNC use
- 48mm body suits a small desktop frame
Cons
- No warranty term is stated
- No step angle is stated
- No shaft size is stated
- Small frame suits light machines, not a heavy gantry
Other machines to compare
STEPPERONLINE Nema 17 Stepper Motor 2A 55Ncm Bipolar 1.8Check price on Amazon
STEPPERONLINE Short Body Nema 17 Bipolar Stepper Motor 1ACheck price on Amazon
STEPPERONLINE 5PCS Nema 17 Stepper Motor Bipolar 2A 84oz.inCheck price on Amazon
STEPPERONLINE CNC Stepper Motor Driver 1.0-4.2A 20-50VDCCheck price on Amazon
Twotrees TTC450 Pro All-Metal CNC Router Machine with NEMA 57Check price on Amazon
CNC Digital Microstep Driver DM542 Stepper Motor DriverCheck price on Amazon
Side by side
| Factor | Nema 17 example | Nema 23 example | Notes |
|---|---|---|---|
| HQ Score | 55 | 60 | Raw totals |
| Holding torque | 59Ncm (83.6oz.in) | 1.9Nm (269oz.in) | Both stated in title and bullets |
| Rated current | 2.0A | 2.8A | As stated in title and bullets |
| Resistance | 1.4 ohms | 1.13 ohms | As stated |
| Step angle | Not stated | 1.8 deg, 200 steps/rev | Nema 17 listing gives no step angle |
| Shaft | Not stated | Single shaft, 6.35mm diameter | Nema 17 listing gives no shaft size |
| Body size | 1.65 x 1.65 x 1.89 in, 48mm body | 2.24 x 2.24 x 3.0 in | Title and bullets; spec tables differ on both |
| Cable | 39.37 in (1m) cable, 0.1 in pitch connector | Not stated | Nema 23 listing gives no cable length |
| Weight | 14.08 ounces | 2.3 pounds | Spec table figures, stated in different units |
| Warranty | Not stated | Not stated | Neither listing states a warranty term |
| Example: STEPPERONLINE Nema 17 | 2.0A, 59Ncm, 1.65 x 1.65 x 1.89 in | Not applicable | Nema 17 side |
| Example: STEPPERONLINE Nema 23 | Not applicable | 2.8A, 1.9Nm, 2.24 x 2.24 x 3.0 in | Nema 23 side |
Size and performance figures are the brand’s ratings quoted from listings on 18 October 2026.
Nema 17 vs Nema 23 CNC: holding torque
Holding torque is the headline difference, and both listings state it clearly. The Nema 17 example lists 59Ncm, with the bullets giving 83.6oz.in and the title rounding that to 84oz.in. The Nema 23 example lists 1.9Nm, or 269oz.in. In ounce-inches, the Nema 23 example lists 269oz.in against 83.6oz.in for the Nema 17 example, which is what you want when the motor must hold a gantry still against cutting forces. Torque alone does not pick the motor, so the sections below cover size, step angle and current.
Body size and shaft
The Nema 17 example measures 1.65 x 1.65 x 1.89 in, with a 48mm body, while the Nema 23 example measures 2.24 x 2.24 x 3.0 in. The Nema 23 listing disagrees with itself on body size too: its spec table lists 2.26 in wide by 3.88 in high, while the title and bullets give 2.24 x 2.24 x 3.0 in, so this article uses the title and bullet figures. The Nema 23 example also states a single shaft of 6.35mm diameter; the Nema 17 listing gives no shaft size, so the two cannot be compared on shaft diameter. The Nema 17 example lists a weight of 14.08 ounces and the Nema 23 example lists 2.3 pounds, stated in different units, so compare each figure against your own mount and frame rather than against each other.
Step angle and steps
The Nema 23 example states a 1.8 deg step angle, or 200 steps per revolution. The Nema 17 listing states no step angle, so do not assume it matches; check the listing or the maker specifications before pairing it with a driver that expects a given step count.
Current and resistance
Both listings state rated current and resistance. The Nema 17 example is rated 2.0A with 1.4 ohms, and the Nema 23 example is rated 2.8A with 1.13 ohms. Check the driver against the rated current the listing states before you buy. The Nema 17 listing contradicts itself here: its spec table lists 1.0A, 18.4oz.in and a 0.79 in body, while the title and bullets agree on 2.0A and 59Ncm, so this article uses the title and bullet figures.
What each one suits
The Nema 23 example suits the heavier side of CNC work: the listing names CNC mill, lathe and router use, with the larger torque figure and the 6.35mm shaft. The Nema 17 example suits a 3D printer or a small CNC build, as the listing names 3D printer and CNC use, with the smaller body and the 1m cable and connector in the box. Neither listing states a warranty term, so neither side wins on support.
Choose the STEPPERONLINE Nema 23 if
- You need the higher stated holding torque, 1.9Nm, for a mill, lathe or router.
- You want the stated 6.35mm single shaft and 1.8 deg step angle.
- Your frame and driver suit a 2.24 x 2.24 x 3.0 in motor rated at 2.8A.
Choose the STEPPERONLINE Nema 17 if
- You are building a compact 3D printer or small CNC machine.
- The 1.65 x 1.65 x 1.89 in body, 48mm long, fits your mount.
- You want the 1m cable and connector that come with the motor, and a 2.0A rated current for a smaller driver.
For more on choosing motors, see stepper motor vs servo motor for CNC and closed loop vs open loop stepper for CNC.
Project Match
- Small desktop CNC or 3D printer: the Nema 17 example, 1.65 x 1.65 x 1.89 in body, 2.0A, 1m cable included.
- CNC mill, lathe or router: the Nema 23 example, 1.9Nm holding torque, 6.35mm shaft.
- Work needing 200 steps per revolution: the Nema 23 example states 1.8 deg; the Nema 17 listing does not state a step angle.
- A build with a driver rated for 2.8A: the Nema 23 example; for a 2.0A driver, the Nema 17 example.
FAQ: lasers and CNC
Can I use a Nema 17 motor on a CNC router?
The Nema 17 example here is listed for 3D printer and CNC use, with 59Ncm holding torque, a 2.0A rated current and a 1.65 x 1.65 x 1.89 in body. Match those stated figures to the machine before you buy.
What is the difference between Nema 17 and Nema 23?
The frame size and the torque: the Nema 17 example here lists 59Ncm and a 1.65 x 1.65 x 1.89 in body, while the Nema 23 example lists 1.9Nm and a 2.24 x 2.24 x 3.0 in body.
Which stepper motor has more holding torque?
The Nema 23 example, at 1.9Nm (269oz.in) against 59Ncm (83.6oz.in) for the Nema 17 example.
Do these motors come with cables?
The Nema 17 example includes a 1m cable with a 0.1 in pitch connector. The Nema 23 listing states no cable, so check what comes in the box before ordering.
What driver do I need for these motors?
Match the driver to the rated current: 2.0A for the Nema 17 example and 2.8A for the Nema 23 example. See our best stepper motor driver for Nema 17 guide.
Related: stepper motor vs servo motor CNC, closed loop vs open loop stepper CNC and best stepper motor driver for Nema 17.




