Best Acrylic Earring Blanks for Laser Engraving (2026): 5 Picks

Specs compared

Specifications are manufacturer rated, as published on each listing and collected 20 October 2026. “Not stated” means the listing does not give the figure.

Best acrylic earring blanks for laser engraving: thickness and type

Thickness runs 2 mm (Bucherry) to 3 mm (Senbota) to 1/8 inch (JINMURY) to 2.5 mm (Audab). For earrings, 2 to 3 mm is the workable range: stiff enough to hold shape, thin enough to cut fast. The Bucherry is the only cast acrylic here, stated as clear cast acrylic in 4 shapes with protective film on both sides, explicitly for laser cutting and engraving. The JINMURY is precision laser-cut 1/8-inch sheet with polished edges, sold as 3 by 7.9 inch rectangles for signs and name plates. The Senbota is 3 mm black acrylic with pre-drilled 4 mm holes; black engraves with high contrast. The Audab is 2.5 mm clear discs, 3.5 inches across, laser cut with a hole, sold for keychains and ornaments. Our acrylic vs wood for laser engraving covers the material choice.

Cutting earring shapes from sheets vs using discs

None of these are earring-shaped, so the practical route is cutting your own shapes. The Bucherry and JINMURY sheets are the fit: flat stock you cut earring pairs from, with the Bucherry stating laser cutting explicitly and the JINMURY arriving already laser cut with smooth edges. The 3.5-inch Audab discs and 3-inch Senbota discs are finished shapes with holes, usable as large pendants or cut down. The SINBRLAI coins are 40 mm brass and zinc, not acrylic, and do not belong in an acrylic workflow; the acrylic in that listing is the protective box, not the blank. See MDF vs acrylic for laser engraving for material trade-offs.

Project Match

• Cutting earring pairs from sheet stock: Bucherry (2 mm cast, 4 shapes) or JINMURY (1/8 in, laser cut).
• High-contrast engraved designs: Senbota black 3 mm discs with pre-drilled holes.
• Clear pendants and keychains: Audab 3.5 in clear discs with hole.
• Metal coins, not acrylic: SINBRLAI brass and zinc 40 mm coins; not for acrylic earring work.

Thicknesses and materials stated

Thickness is stated on four of the five listings. The Audab states 2.5 mm thick clear discs in a 30-piece pack at 3.5 inches with a hole, laser cut from acrylic sheet with smooth edges and high transparency. The Bucherry states 2.0 mm (0.08 inch) clear cast acrylic in a 20-piece pack across 4 shapes. The JINMURY states 1/8 inch thick (0.125 inch in the bullets, 0.13 inches in the spec table) transparent plexiglass in a 10-piece pack at 3 by 7.9 inches, laser cut with polished edges. The Senbota states 3 mm (0.12 inch) black circular blanks in a 20-piece pack at 76 mm (3 inches) with a 4 mm (0.16 inch) hole. The SINBRLAI states solid brass and zinc alloy coins at 40 mm diameter with a mirrored surface and silver plating, in a 10-piece pack with an acrylic protection box. For earrings, the stated 2 to 3 mm acrylic thicknesses are the workable range; the brass coins are the metal alternative.

Protective film and finishes

Protective film is stated on three listings. The Audab states a milky white film on both sides that leaves no residue when peeled, protecting the discs during packaging and shipping. The Bucherry states protective films on both sides to be removed before use, on PET sheets. The JINMURY states a protective film on both sides to prevent scratches. The Senbota states an uncoated black finish with no film mentioned. The SINBRLAI states a mirrored coin surface with an acrylic protection box included. For engraving, the film stays on during the job on the Audab, Bucherry and JINMURY pieces, then peels for a clean surface; the Senbota’s stated uncoated black acrylic is the high-contrast engraving story.

Stated uses and compatibility

Stated uses frame each blank. The Audab states engraving, vinyl, epoxy items, keychains, ornaments, gift tags and pendants. The Bucherry states LED light bases, house numbers, table numbers, nameplates and menus, with hot cutting (laser) or cold cutting (saw) and utility-knife DIY cutting. The JINMURY states name plates, place cards, Cricut cutting and engraving, with paint that removes with rubbing alcohol or olive oil for reuse. The Senbota states vinyl, UV printing and engraving on the black blanks, with resin embedding for custom keychains. The SINBRLAI states DIY crafts engraving on the brass and zinc coins. For earring blanks specifically, the Senbota’s stated 3-inch black circles and the Audab’s 3.5-inch clear discs are the closest stated fits; the Bucherry’s stated 4 shapes give cutting options.

Weights and dimensions

Stated weights: the Audab at 0.43 kg, the JINMURY at 0.59 kg, and the Senbota at 280 g; the Bucherry states 10.12 by 6.3 by 2.09 inch item dimensions with no weight, and the SINBRLAI states 1.77 by 1.77 by 0.26 inch coins with 10.58 ounce product dimensions. Stated piece counts: 30 Audab discs, 20 Bucherry sheets, 10 JINMURY plates, 20 Senbota circles and 10 SINBRLAI coins. For a seller making earrings in batches, the stated 30-piece Audab and 20-piece Senbota packs are the volume story.

How the scores add up

Each blank is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. None of the five listings states a safety certification or a warranty term, so all score 0 for safety and warranty. The SINBRLAI is scored as listed: a brass and zinc alloy coin, not an acrylic blank.

Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.

FAQ: lasers and CNC

What thickness acrylic for earrings?

The listings here run 2 mm to 1/8 inch. For earrings, 2 to 3 mm is the workable range: the Bucherry at 2 mm and the Senbota at 3 mm sit in it, and the JINMURY at 1/8 inch is just above.

Is cast or extruded acrylic better for engraving?

The Bucherry is the only listing here that states cast acrylic, and it is stated for laser cutting and engraving. The others do not state cast or extruded.

Do these come with holes for earring hooks?

The Audab discs and Senbota discs state pre-drilled or cut holes. The Bucherry and JINMURY are sheets with no holes stated. The SINBRLAI coins are metal, not acrylic.

Which are actually earring blanks?

None are earring-shaped. They are general acrylic blanks, discs and sheets you cut earring shapes from. The SINBRLAI is a brass and zinc coin, not an acrylic blank at all.

Do any state a warranty?

None of the five listings states a warranty term or a safety certification.

Related: best wood for laser engraved cutting boards, best wood keychain blanks for engraving, slate vs acrylic coasters laser engraving and the engraving materials hub.