Hips vs Abs Filament: Which One Should You Buy?
HIPS and ABS filaments compared as dissolvable support versus tough part material, on diameter, tolerance, spool size, print temperatures and warranty.
On this page
A print with deep overhangs needs supports that come away cleanly, while a functional part needs a filament that holds up under use. That split is the whole hips vs abs filament question: HIPS works as a dissolvable support for complex ABS prints, and ABS works as the tough part material itself. This comparison puts two Gizmo Dorks HIPS spools, white and black, against one Creality ABS spool, using what each listing states.
As an Amazon Associate I earn from qualifying purchases. LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Verdict: pick the HIPS side when the print needs supports that dissolve away in d-Limonene, especially for complex ABS prints from a dual-extrusion setup. Pick the ABS side when the print itself must be a tough engineering part with heat resistance. The two sides answer different jobs, so the choice follows the print, not the spool color.
Side by side
| Spec | Creality ABS Black | Gizmo Dorks HIPS White | Gizmo Dorks HIPS Black |
|---|---|---|---|
| HQ Score | 66 | 59 | 57 |
| Diameter | 1.75mm | 1.75mm | 1.75mm |
| Spool | 1 kg | 1 kg, 2.2 lb | 1 kg, 2.2 lb |
| Tolerance | +/- 0.02mm | +/- 0.02mm | +/- 0.02mm |
| Support use | Not stated | Dissolves in d-Limonene | Dissolves in d-Limonene |
| Print temperatures | Not stated | 230C to 250C extruder, 90C to 110C bed | Not stated |
| Warranty | 1 Year | Not stated | Not stated |
Specifications are manufacturer rated, as published on each listing and collected 4 November 2026.
HIPS as a dissolvable support
Both Gizmo Dorks HIPS listings describe the same job: a high-impact polystyrene that functions as a standalone primary building material or as a dissolvable support structure. Used as a support in a dual-extrusion build, it dissolves in d-Limonene, which suits complex ABS prints where supports would be hard to pull away by hand. Used as a main material, the white listing says it can be sanded, drilled, or painted. The two HIPS listings differ in print guidance, apart from color: the white listing states recommended print parameters, an extruder temperature range of 230C to 250C and a heated bed temperature of 90C to 110C, while the black listing states no print temperatures at all, so the black spool leaves that choice to the printer profile.
ABS as the part material
The Creality ABS listing presents CR-ABS as an engineering filament with impact resistance and heat resistance, tough, hard and rigid, with good dimensional stability and wear and corrosion resistance. For large objects with edges and corners, the listing says layer separation, warping and splitting are obviously improved against ordinary ABS, and the printed result is smooth with strong fluidity. The listing describes the filament as odorless and non-toxic, and it asks for storage in a dry and ventilated environment, away from high temperature, sun and humidity. The filament dry box guide covers storage options for spools kept between prints.
Diameter, tolerance and spool
All three listings share a 1.75mm diameter, and all three state a tolerance of +/- 0.02mm, so diameter and tolerance do not separate the sides here. Spool size also matches at 1 kg: the HIPS listings state 1 kg and 2.2 lb spools, and the Creality listing states a 1 kg pack. Where the listings differ is what they state around those shared figures: only the HIPS white listing gives print temperatures, and only the Creality listing states a warranty, a 1 Year term, while neither HIPS listing states a warranty term. Neither side states a heat resistance figure for HIPS, and neither HIPS listing states a storage condition, so those points stay with the listings that state them.
hips vs abs filament: which side fits your print
Choose HIPS when supports are the problem: a complex ABS print with overhangs that hand removal would damage, printed on a dual-extrusion setup with d-Limonene on hand for dissolving. Choose ABS when the part itself carries the load: an engineering part that needs impact and heat resistance, printed as a single material. Color does not change the HIPS job, since the white and black listings describe the same material, tolerance and spool size, apart from the missing print temperatures on the black listing. When neither side states a figure, such as print temperatures for the Creality spool, treat it as unstated rather than as a win for the other side.
Project Match
- Complex ABS prints with hard-to-reach supports: Gizmo Dorks HIPS, white or black, dissolved in d-Limonene after a dual-extrusion print.
- Tough standalone prototypes: Gizmo Dorks HIPS as a main material that can be sanded, drilled, or painted, or Creality ABS as an engineering part material.
- Large objects with edges and corners: Creality ABS, whose listing claims improved results against ordinary ABS for layer separation, warping and splitting.
- Prints where support removal must leave a clean surface: Gizmo Dorks HIPS as a dissolvable support; the Creality listing states no dissolvable support use.
FAQ: lasers and CNC
Can HIPS be used as a main material, not just a support?
Yes, the Gizmo Dorks listings say HIPS functions as a standalone primary building material as well as a dissolvable support structure, and the white listing says it can be sanded, drilled, or painted when used as a main material.
What dissolves HIPS supports?
d-Limonene, when HIPS is used as a dual-extrusion support material for complex ABS prints, according to both Gizmo Dorks listings.
Do HIPS and ABS share a diameter?
Yes, all three listings state a 1.75mm diameter with a tolerance of +/- 0.02mm, and all three come as 1 kg spools.
Which filament states a warranty?
Only the Creality ABS listing states one, a 1 Year term. Neither Gizmo Dorks HIPS listing states a warranty term.
What print temperatures does the HIPS white listing recommend?
An extruder temperature range of 230C to 250C and a heated bed temperature of 90C to 110C. The black HIPS listing and the Creality ABS listing state no print temperatures.
Related: PLA vs ABS filament, PETG vs ABS filament, ABS vs ASA filament and best filament dry box.
