Best Filament Dryer for TPU (2026): 5 Picks Compared
Five filament dryers for TPU printing compared by spool capacity, temperature range, heater power and safety cutoff.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallSovol SH029.6/10View on Amazon - 2
Best 4-SpoolCreality Space Pi X49.5/10View on Amazon - 3
Dual Spool PickCreality Space Pi Plus9.5/10View on Amazon - 4
Easy Control PickSUNLU S29.4/10View on Amazon - 5
Creality 2026 New Upgrade Filament Dryer Box ProView on Amazon - 6
SUNLU Official Filament Dryer S2View on Amazon - 7
SUNLU Filament Dryer S1 PlusView on Amazon - 8
2026 New Official CREALITY Filament Dryer Space Pi SEView on Amazon - 9
Creality Filament Dryer Box 4 SpoolsView on Amazon
A spool of TPU that has taken on moisture prints with stringing, bubbling and clogging, and a dryer that only warms the outside leaves the core damp. That is the job the best filament dryer for tpu is built for: a box that circulates hot air for even drying and feeds filament straight to the printer.
LaserEngraveHQ earns a commission from purchases made through these links, at no extra cost to you. Read our affiliate disclosure.
Quick picks
- Best Overall Sovol SH02: 2 rolls of 1 kg, 150W PTC heater and PTC cutoff with fan alarm Check price on Amazon
- Best 4-Spool Creality Space Pi X4: 4 spools with dual independent chambers up to 85°C Check price on Amazon
- Dual Spool Pick Creality Space Pi Plus: 2 rolls of 1 kg with one-key settings for 12 filament types Check price on Amazon
- Easy Control Pick SUNLU S2: Custom temperature from 35 to 70°C and time from 0 to 99 hours Check price on Amazon
Machines on the list
Sovol Filament Dryer, SH02 Dry Box 3D Printer
A dual-spool dryer with a 150W PTC heater, one-key settings for 9 filament types and PTC cutoff with a fan-stop alarm.
Pros
- 2 rolls of 1 kg at the same time, with 2 filament holes for PTFE pipes
- 150W PTC heater reaches 50°C within 7 mins and 70°C within 25 mins
- One-key temperature setting for 9 filament types, including TPU
- PTC cutoff over 130°C, resume below 90°C, and a fan-stop alarm
Cons
- Desiccant bags are not included in the package
- No warranty term is stated
- Maximum temperature is 70°C
- A stopped fan sounds an alarm and prompts fan replacement
Official Creality Filament Dryer
A 4-spool dryer with dual independent heating chambers, dual 200W PTC heaters and a maximum temperature of 85°C.
Pros
- 4 spools dry and print at once, with 8 filament holes and PTFE tubing
- Dual chambers with independent temperature control for 2 filament types at once
- Dual 200W PTC heaters reach up to 85°C for engineering filaments
- Single or dual chamber modes for flexible drying
Cons
- No warranty term is stated
- No safety feature is stated
- Other brands' plastic trays must be heat resistant, per the listing note
- Two filament types at different temperatures at once, not four
2026 New Official CREALITY Space Pi Filament Dryer
A 2-roll dryer with a 160W PTC heater, one-key settings for 12 filament types and a 4-inch touchscreen.
Pros
- 2 rolls of 1 kg with 4 filament holes and 2 PTFE pipes
- 160W PTC heater with a built-in fan circulating hot air 360°
- One-key temperature settings for 12 filament types, including TPU
- Temperature adjustable between 45°C and 70°C, with a 4-inch touchscreen
Cons
- No warranty term is stated
- No safety feature is stated
- Capacity is 2 rolls of 1 kg
- Filament types outside the 12 presets need manual temperature adjustment
SUNLU Filament Dryer S2, Black
A filament dryer with a maximum temperature of 70°C, customizable time from 0 to 99 hours and a large touchscreen.
Pros
- Temperature customizable from 35 to 70°C and time from 0 to 99 hours
- Dries filament during printing, with a built-in spindle for even drying
- Large capacity of 265x274x118 mm, for 1.75 mm, 2.85 mm and 3.00 mm filaments
- Translucent lid allows checking filament without opening the lid
Cons
- No warranty term is stated
- No heater wattage is stated
- No safety feature is stated
- Capacity is given as 265x274x118 mm, with no spool count stated
Polymaker Filament Dryer & Storage Box Polydryer
A dryer and storage box that dries, stores and prints without breaking the seal, with a built-in hygrometer and desiccant protection.
Pros
- Dry, store and print without breaking the seal, with direct filament feeding
- Built-in hygrometer for monitoring dry conditions
- Sealed storage plus desiccant protection for ongoing moisture defense
- Fits 1.75 mm, 2.85 mm and 3.00 mm filaments, including TPU
Cons
- Temperature range is Not stated
- Heater wattage is Not stated
- Warranty term is Not stated
- Safety feature is Not stated
Other machines to compare
Creality 2026 New Upgrade Filament Dryer Box ProCheck price on Amazon
SUNLU Official Filament Dryer S2Check price on Amazon
SUNLU Filament Dryer S1 PlusCheck price on Amazon
2026 New Official CREALITY Filament Dryer Space Pi SECheck price on Amazon
Creality Filament Dryer Box 4 SpoolsCheck price on Amazon
Specs compared
| Dryer | HQ Score | Spools | Max temp | Heater | Feed while printing | Safety | Warranty |
|---|---|---|---|---|---|---|---|
| Sovol SH02 | 9.6/10 | 2 rolls of 1 kg | 70°C | 150W PTC | Yes, PTFE pipes | PTC cutoff and fan alarm | Not stated |
| Creality Space Pi X4 | 9.5/10 | 4 spools | 85°C | Dual 200W PTC | Yes, PTFE tubing | Not stated | Not stated |
| Creality Space Pi Plus | 9.5/10 | 2 rolls of 1 kg | 70°C | 160W PTC | Yes, PTFE pipes | Not stated | Not stated |
| SUNLU S2 | 9.4/10 | Not stated | 70°C | Not stated | Yes, dry during printing | Not stated | Not stated |
| Polymaker Polydryer | 9.4/10 | 1 kg | Not stated | Not stated | Yes, direct feeding | Not stated | Not stated |
Specifications are manufacturer rated, as published on each listing and collected 3 November 2026. Temperature is the maximum each listing states for its own dryer.
What the listings tell you, and what they leave out
The five listings state temperature, heater power and spool capacity in different ways, and some figures need a closer look. Only the Sovol SH02 states a safety cutoff, at over 130°C with resume below 90°C. None of the five listings states a warranty term with a concrete unit: the SUNLU listing gives only a bare figure of 1, so its warranty is Not stated here. The Polymaker listing states no temperature range and no heater wattage. Temperature for the Space Pi Plus runs from 45°C to 70°C, for the Sovol SH02 from 40°C to 70°C, and for the SUNLU S2 from 35°C to 70°C, while the Space Pi X4 reaches up to 85°C.
Buying guide: choosing the best filament dryer for tpu
Temperature range and TPU presets
The Space Pi Plus gives one-key settings for 12 filament types, including TPU, with temperature adjustable between 45°C and 70°C. The Sovol SH02 gives one-key settings for 9 filament types, including TPU, with temperature from 40°C to 70°C. The SUNLU S2 gives no preset list, but temperature adjusts from 35°C to 70°C and time from 0 to 99 hours. The Space Pi X4 reaches up to 85°C, which the listing ties to engineering filaments. Temperature for the Polymaker Polydryer is Not stated.
Spools, chambers and feed
The Space Pi X4 dries and prints 4 spools at once. The Space Pi Plus holds 2 rolls of 1 kg. The Sovol SH02 holds 2 rolls of 1 kg. The SUNLU S2 gives a capacity of 265x274x118 mm, with no spool count stated. The Polymaker Polydryer dries, stores and prints without breaking the seal, with direct filament feeding. The Space Pi Plus, the Sovol SH02 and the Space Pi X4 all feed through PTFE pipes or tubing.
Safety and sealing
Only the Sovol SH02 states a safety cutoff, with PTC cutoff over 130°C, resume below 90°C and a fan-stop alarm. Safety for the other dryers is Not stated. The Polymaker Polydryer pairs sealed storage with desiccant protection and a built-in hygrometer. The Sovol SH02 sealing protects filament from moisture and dirt even when it is not powered on, though desiccant bags are not included.
Project Match
Match the dryer to the work you do most, using only what each listing states:
- Two printers at once: the Space Pi Plus with 2 rolls and 2 PTFE pipes, and the Sovol SH02 with 2 rolls of 1 kg.
- Four printers at once: the Space Pi X4 with 4 spools, 8 filament holes and PTFE tubing.
- Storage between prints: the Polymaker Polydryer with sealed storage, desiccant protection and a hygrometer, and the Sovol SH02 with sealing that protects filament when not powered on.
- TPU presets at a tap: the Space Pi Plus with one-key settings for 12 types, and the Sovol SH02 with one-key settings for 9 types.
- Custom time and temperature: the SUNLU S2 with temperature from 35 to 70°C and time from 0 to 99 hours.
How the scores add up
Each dryer is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. A spec the listing does not publish scores nothing.
| Product | HQ Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Sovol SH02 | 9.6 | 29 | 21 | 21 | 8 | 0 |
| Creality Space Pi X4 | 9.5 | 32 | 22 | 20 | 0 | 0 |
| Creality Space Pi Plus | 9.5 | 30 | 21 | 21 | 0 | 0 |
| SUNLU S2 | 9.4 | 28 | 20 | 21 | 0 | 0 |
| Polymaker Polydryer | 9.4 | 26 | 21 | 20 | 0 | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.
FAQ: lasers and CNC
How does a filament dryer work?
A dryer circulates hot air around the spool to remove moisture, with a fan for even heating. The Space Pi Plus and the Sovol SH02 both circulate hot air 360° with a built-in fan.
Why do I need a filament dryer for TPU?
TPU is listed for all five dryers here. The Polymaker listing links moisture to stringing, bubbling, clogging and layer inconsistency.
Do I need a filament dryer for PLA?
PLA is listed for all five dryers here. The SUNLU listing notes that filaments absorb moisture from the air, especially in humid places.
Which dryer has a safety cutoff?
The Sovol SH02 has PTC cutoff over 130°C, resume below 90°C, and a fan-stop alarm. The other dryers state no safety cutoff.
Related: the 3D printers hub, 3D printer accessories, PLA vs TPU filament, and filament dryer vs food dehydrator.
